Etherma LAVA Setup guide

www.etherma.com
LAVA®& LAVA®-DM
DESIGN INFRARED HEATER
Installation and Usage Instruction
CAUTION: hot surface!
Can cause burns!

INTRODUCTION
GENERAL
With your choice of ETHERMA you have decided on an ingenious hea-
ting solution. We thank you for your condence. In us you have a com-
petent partner with more than 35 years of experience. ETHERMA relies
on constant innovation , highest product quality and modern design.
We support you with comprehensive personalized services and nd the
right product solution for you.
The following instructions will help you, to use your ETHERMA quality
product as effective as possible. They contain important information
about safety, installation, use and maintenance of the devices. Please
read the information in this instruction carefully and keep them for
feedback at a later time on.
LAVA®design infrared heaters from ETHERMA are direct
heaters which are versatile in use. Further on they attract by
elegant design, simple installation and easy operation. High
reliability and maximum performance with minimal radiation
convection convince our costumers.
This guide provides important information on safety, installa-
tion, use and maintenance of the equipment. Please read the
information carefully.
The manufacturer is not liable if the following instructions are
not followed. The devices may not be misused.
The packaging of your LAVA®design infrared heater consists of
recyclable materials.
ATTENTION: Operation of the heater causes high tempe-
rature on the glass surfaces. Prolonged contact may cause
burns. Please make sure, that children or inrm persons don’t
get in touch with it.
This heater is not intended for use by persons (including child-
ren) with reduced physical, sensory or mental capabilities or
lack of experience and knowledge of using the radiator. Unless
they are supervised by a person responsible for safety or recei-
ved instructions about how the device should be used. Children
should be supervised to ensure that they do not play with the
device.
The heater must not be placed or mounted directly below a wall
socket.
WARNING: Covering the surface causes
overheating danger! Already a local covering
of the pane, for example with a towel can
lead to overheating and cause damage of the
heating element.
WARNING: Do not use the heater if the front is broken.
Overheating and overload protection
Each heater has an overheating protection. The device automa-
tically starts again after a cooling down to under 45 °C.
These instructions must
› be passed to the operator after the installation. In addition,
the operator is trained in the operation of the radiation heater.
› be carefully kept and handed over at change of ownership to
the new owner.
2
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER
CAUTION: Do not switch on the LAVA®CERAMIC
until the ceramic plate has adapted to the ambient
temperature.

TYPES:
LAVA®BASIC 2.0
With the LAVA®BASIC 2.0 the surface was further optimised,
thus increasing the radiation power and effect. In addition to
the benefit of the new attractive design, towel holders can also
be mounted.Thanks to the new Plug & Play connection system,
integrated LAVA®-R control, a LAVA®-F radio receiver or a wi-
red room thermostat can be connected.
LAVA®GLAS 2.0
LAVA®GLASS 2.0 offers designer infrared heating that impres-
ses with its comfortable infrared radiation and its aesthetic
features. LAVA®GLASS 2.0 is available in 4 standard colours
(pure white, white-green, black, red) and in a mirror version,
as well as with 6 different outputs. Each LAVA®GLASS can be
mounted vertically or horizontally on the wall. For warm tow-
els in your bathroom, towel rails (Halti) can be attached to any
LAVA®GLASS 2.0 unit.
LAVA®CERAMIC
The new LAVA®CERAMIC is a design infrared heater that is
characterised by its uniform infrared heat and its elegant look.
LAVA®CERAMIC is available as standard in 3 different colours
(Calacatta, Titanium White, Ebony Black) as well as in 4 out-
puts. Each LAVA®CERAMIC can be mounted vertically or ho-
rizontally on the wall. For warm towels in the bathroom, towel
rails (Halti) can now be attached to each LAVA®CERAMIC.
Plug & Play-connection system:
LAVA® BASIC Modelle
All LAVA®infrared heaters are supplied without a control, a
plug lead and an ON/OFF switch. They are, therefore, ideal for
new construction and anywhere where wired room thermos-
tats are used. The Plug & Play connection system (IP65) allows
direct connection to a wired room thermostat, easy integration
with a radio receiver LAVA®-F or direct control on the device
with the LAVA®-R thermostat.
LAVA®-R:
All LAVA® 2.0 infrared heaters can be tted with a thermostat
which has been developed specically for infrared heaters. The
thermostat controls the room temperature and optimises the
surface temperature of the LAVA®. Furthermore, the surface
temperature in children‘s rooms and bathrooms, for example,
can be limited to 60 °C with a switch. The adjustable tempera-
ture range is 5 to 35 °C.
LAVA®-F:
Radio-controlled thermostats avoid complex elevation and
plaster work for cable routing and allow easy installation of
heaters. The LAVA®-F radio receiver can be quickly tted to
all LAVA®2.0 using the connection system. The receivers are
controlled with the ET-11A or ET-12A radio thermostat (please
order separately), which can control up to 99 LAVA®-F radio re-
ceivers. The ET-12A has a programmable week program, frost
protection function, manual mode and on/off function.
WIRED ROOM THERMOSTATS:
Ideal for new buildings and renovation, for example when old
night storage heaters, which were controlled by thermostat, are
replaced.
OVERVIEW OF TYPES AND VERSIONS
This device can be used by children of 8 years and above and by
persons with reduced physical, sensory or mental abilities and
with a lack of experience or knowledge if they are supervised
or have been instructed on safe use of the device and under-
stand the resulting risks. Children may not play with the device.
Children may not carry out cleaning and user maintenance wi-
thout supervision. The heater may not be used if the glass is
damaged. The heater may not be covered as this can cause the
device to overheat. Children under the age of 3 should be kept
away unless under constant supervision. Children between the
ages of 3 and 8 may only switch the device on and off if they are
supervised or have been instructed regarding safe use of the
device and understand the resulting risks, as long as the device
is placed or installed at its normal place of use. Children bet-
ween the ages of 3 and 8 may not plug the device in, regulate
the device, clean the device and/or carry out user maintenance.
The device may only be operated once installed. This heater
may not be used in the immediate vicinity of a bathtub, shower
or swimming pool. The heater may not be used in small rooms
where persons live who cannot leave the room independently,
except where constant supervision is ensured.
CAUTION: Any kind of load on the surface, whether from
persons or objects leaning against it or from other forces, must
be avoided.
Some product parts can become very hot and cause burns.
Particular caution is required when children or vulnerable per-
sons are present.
3
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

Delivery wall mounting:
LAVA®design infrared heater
› 1 x wall mounting hardware:
- 2 x mounting bracket
- 4 x hex bolt M8 x 16
DELIVERY | PACKAGING WALL MOUNTING
The LAVA® design infrared heater has to be xed only with the
supplied mounting hardware for wall mounting, which are in-
cluded. Screws and anchors (not included) must correspond
with the building material of the wall (masonry, concrete, plas-
terboard, etc.). The wall must have a at surface.
4
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

Graphic: Minimum mounting distances
CAUTION:
Any kind of load on the surface, whether from persons or ob-
jects leaning against it or from other forces, must be avoided.
INSTALLATION AND USAGE INSTRUCTION FOR THE ELECTRICIAN
35 mm
35 mm
35 mm
35 mm
Important Notes:
ETHERMA’s LAVA® design infrared heater fullll the relevant
safety regulations.
› Installation and commissioning, repair and service work
must be carried out by a licensed professional or a qualied
person in compliance with all security regulations. First this
person must check if the electrical installation complies with
the applicable standards in the house. The responsibility of
the manufacturer is limited to the supply of the device.
› Please note the country-specic security rules.
› Local protection measures have to be observed.
› The devices are designed for wall mounting (vertical or ho-
rizontal) with the appropriate accessories (see included de-
livery).
› Wall mounting of the design infrared heater corresponds
IP 24 protection.
› When installing the unit in a bathroom note the areas of pro-
tection to DIN VDE 0100 Part 701.
› Specied minimum distances must be respected.
Installation and minimum distances:
LAVA®design infrared heaters can be mounted horizontally or
vertically on the wall. They are positioned so that ammable
items can not be ignited. Mind the minimum distances, particu-
larly to ammable objects like curtains, upholstered furniture,
and so on are correct. Please make sure, that the glass heating
device can radiate free into space.
Assembly of the heating device:
Please check before installing the power cable to the radiator,
and the glass plate. There shouldn’t be any damage.
Wall mounting:
1. Perform wall-holes – please note the predetermined hole-
pattern (see p. 6 ff.).
2. Mount the mounting bracket (see delivery) on the wall Note:
screws and anchors (not included) must match the building
material of the wall.
3. Position cable clamp and place LAVA®infrared heater on the
wall and tighten the screws completely.
4. To protect the glass radiator against unintentional take down,
etc. the protection-plate (included in delivery) should be afxed
to one of the 4 mounting brackets.
5
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

ATTENTION: Mind minimum distances! Use required mounting holes!
HOLE SPACING FOR DRILLING – WALL MOUNTING
LAVA®BASIC | GLAS | CERAMIC | Design Your LAVA®| IMAGE 250
LAVA®BASIC | GLAS | CERAMIC | Design Your LAVA®| IMAGE 500
vertical
front view
vertical
front view
horizontal
front view
horizontal
front view
cable with plug
cable with plug
cable with plug
cable with plug
6
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

HOLE SPACING FOR DRILLING – WALL MOUNTING
ATTENTION: Mind minimum distances! Use required mounting holes!
LAVA®GLAS 600
LAVA®GLAS 800
vertical
front view
vertical
front view
horizontal
front view
horizontal
front view
cable with plug
cable with plug
cable with plug
cable with plug
7
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

HOLE SPACING FOR DRILLING – WALL MOUNTING
LAVA®BASIC | GLAS | CERAMIC | Design Your LAVA®| IMAGE 750
LAVA®BASIC | GLAS | CERAMIC | Design Your LAVA®| IMAGE 1000
ATTENTION: Mind minimum distances! Use required mounting holes!
vertical
front view
vertical
front view
cable with plug
cable with plug
horizontal
front view
horizontal
front view
cable with plug
cable with plug
8
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

Delivery ceiling mounting:
LAVA®design infrared heater
› 1 x hardware ceiling mounting:
- 4 x ceiling mounting bracket
- 4 x screw M3 x 6
- 4 x LAVA Secure – glass safety hook
- 4 x hex bolt M8 x 20
(optional might already preinstalled on the device)
- 1 x cable holder
After xing do not tighten completely!
DELIVERY | PACKAGING CEILING MOUNTING
The LAVA® design infrared heater has to be xed only with the
supplied mounting hardware for ceilings, which are included.
Screws and anchors (not included) must correspond with the
building material of the ceiling (masonry, concrete, plaster-
board, etc.). The ceiling must have a at surface.
Ceiling installation:
1. Drill the holes into the ceiling – please observe the prescri-
bed distances between holes (see p.10 ff).
2. Mount the assembly rails on the ceiling. CAUTION:screws
and dowels (not included in the scope of delivery) must corres-
pond to the construction material of the ceiling.
3. Attach safety hooks and distance washers to the 4 assembly
screws on the body.
4. Attach the LAVA®design infrared heater to the ceiling. Some
safety hooks for ceiling installation are already tted at the fac-
tory – between the glass front and the body – to provide further
mechanical security to the glass front. Not valid for LAVA®
BASIC-DM.
5. Finally tighten the installation screws.
6. Only devices in the series LAVA® BASIC-DM and LAVA®
GLAS-DM may be installed on the ceiling.
For ceiling mounting there are own glass-safety hooks – LAVA®
Secure – already factory-installed, which also protect the glass
radiator. Ceiling assembly must be separately ordered
LAVA®Secure
LAVA®Ceiling Holder
Graphic: Ceiling assembly - LAVA®design infrared heater
9
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

HOLE SPACING FOR DRILLING – CEILING MOUNTING
ATTENTION: Mind minimum distances! Use required mounting holes!
10
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER
LAVA®BASIC-500DM LAVA®BASIC-750DM
LAVA®BASIC-1000DM LAVA®BASIC-1500DM
562,5 562,5
connection
connection
connection
connection

HOLE SPACING FOR DRILLING – CEILING MOUNTING
ATTENTION: Mind minimum distances! Use required mounting holes!
11
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER
LAVA®GLAS-500DM
LAVA®GLAS-1000DM
LAVA®GLAS-750DM
LAVA®BASIC-350DM
connection
connection
connection
connection

ATTENTION:If the power cord of the unit is damaged, it
must be replaced immediately.
The device is connected to the AC mains system with the inclu-
ded plug and socket with connected power cord and a connec-
tion socket on the installation side.
If a longer power cord is required then the cord can be ex-
changed for a longer one of type H05VV-F 3 x1.0 mm². A direct
connection to an installed line is only permitted up to a diame-
ter of 1.5 mm² (e.g. NYM-J 3 x 1.5 mm²).
An all-pole disconnecting device with a contact opening width
of at least 3 mm must be installed in the fixed electrical instal-
lation in accordance with wiring rules on the installation side.
Heating
The heater is either controlled by the externally moun-
ted thermostat (LAVA®) or via a wireless room thermostat
(LAVA®-F) or via the already integrated thermostat (LAVA®-R).
In the wireless versions (LAVA®-F) the wireless receiver is
already integrated on the device. The wireless room ther-
mostat, which is necessary for the operation is not included.
This can be ordered as accessory (see p. 7). Please refer to the
manual of the room thermostat.
Graphic: connection diagram
USER INSTRUCTION
Electrical connection
The heater is designed for permanent connection to a wall jack
or socket. The control has to be done due to a suitable room
thermostat. Please refer to the instructions of the room ther-
mostat.
wall jack/
socket
Heating
Depending on the thermal insulation standard, you need a heat
output from 30 to 200 W/m². The LAVA®design infrared heater
has a very high radiation fraction and a low proportion of the
convective heat output. For safety reasons, the surface tem-
perature, is max. about 95 °C, thus the overall performance of
the device is limited. For this reason, these devices are used
only in very well insulated houses as a sole heating solution.
ETHERMA LAVA®design infrared heaters warm predominantly
solid objects and only a small proportion of the air directly, so
these devices are ideal for additional temperature control. In or-
der to achieve the same feeling of comfort as with a convection
heating, the indoor air temperature can be lowered by 2-3 °C.
Each degree reduction can save about 6 % heating costs, depen-
ding on the respective heating behavior and thermal insulation
standard. Only if a room is actually used, the LAVA®design in-
frared heater is additionally turned on and the radiation provi-
des a cosy feeling.
Depending on the size of the device the LAVA®design infrared
heater requires some time until it reaches operating tempe-
rature. Only after that the radiation comes into full effect. The
produced glass sheet for the product consists of 6 mm toughe-
ned safety glass (ESG). This is in contrast to conventional glass
much more resistant and is designed for signicantly higher
impact forces. However, you should avoid excessive use. In
case of damage ESG shatters into many small pieces with blunt
edges, to minimize the risk of injury.
Please note in locating, that it can come to a very small per-
centage of toughened glasses yet to so-called "spontaneous
breakage", i.e that the glass shatters, even without external
inuence. Choose the setup of the device in a way that also in
this case there is no danger to people or objects.
ATTENTION: Any kind of load on the whether by leaning effects
of persons or objects, or by other forces have to be avoided!
Please note that you don’t place any objects between the LAVA®
design infrared heater and the persons to be heated. In this
case, the goods and not the peole would be heated.
Maintenance and care
The LAVA®design infrared heater is designed in a way, that it
provides its heat over the glass surface in the form of radiation.
There are no parts located on the device that require special
maintenance. For the care of your glass radiator, we recom-
mend commercial glass cleaner. Please do not use abrasive
cleaners, as these can cause scratches to the glass as well as
the painted surface.
ATTENTION: For cleaning the LAVA®design infrared heater
have to be cold!
Spare Parts
For any replacement parts required please ask your dealer.
Only use original spare parts.
12
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

› Voltage: 230 V
› Surface: smooth, heating-optimised
surface
› Protection: IP X4
› Protection class: I
› Approval: CE compliant
› Colors: White RAL 9016
› Surface Temperature: 95 °C (max)
› Device/Installation depth: 26/57 mm
› Factory warranty: 5 Years
› Voltage: 230 V
› Surface: 6 mm ESG safety glass
› Protection: IP X4
› Protection class: I
› Approval: CE compliant
› Colors: Purewhite, White Green, Black, Red,
Mirror and other Designs
› Surface Temperature: 95 °C (max)
› Device/Installation depth: 30/61 mm
› Factory warranty: 5 Years
› Voltage: 230 V
› Surface: 6 mm special ceramics
› Protection: IP X4
› Protection class: I
› Approval: CE compliant
› Colors:
Calacatta, Titanium White, Ebony Black
› Surface Temperature: 95 °C (max)
› Device/Installation depth: 30/60 mm
› Factory warranty: 5 Years
Type Output (W) Measurements (mm) Weight (kg)
Length Height
LAVA-GLAS2-250 250 500 630 10
LAVA-GLAS2-500 500 900 630 15
LAVA-GLAS2-600 600 1300 500 18
LAVA-GLAS2-750 750 1300 630 23
LAVA-GLAS2-800 800 1600 500 28
LAVA-GLAS2-1000 1000 1600 630 33
Type Output (W) Measurements (mm) Weight (kg)
Length Height
LAVA-CERAMIC-250 250 500 630 10
LAVA-CERAMIC-500 500 900 630 15
LAVA-CERAMIC-750 750 1300 630 23
LAVA-CERAMIC-1000 1000 1600 630 33
TECHNICAL DATA LAVA®BASIC 2.0
TECHNICAL DATA LAVA®GLAS 2.0
TECHNICAL DATA LAVA®CERAMIC
Type Output (W) Measurements (mm) Weight (kg)
Length Height
LAVA-BASIC2-250 250 500 630 8
LAVA-BASIC2-500 500 900 630 12
LAVA-BASIC2-750 750 1300 630 18
LAVA-BASIC2-1000 1000 1600 630 21
13
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

› Voltage 230 V
› Surface: 6 mm ESG safety class
› Protection: IP X4
› Protection class: I
› Approval: CE compliant
› Colors: Individual
› Surface Temperature: 70 °C (max)
› Device/Installation depth: 30/61 mm
› Factory warranty: 5 Years
› Voltage: 230 V
› Surface: 6 mm ESG safety class
› Protection: IP X4
› Protection class: I
› Approval: CE compliant
› Colors: Individual
› Surface Temperature: 70 °C (maximal)
› Device/Installation depth: 30/61 mm
› Factory warranty: 5 Years
› Voltage: 230 V
› Surface: Structured surface
› Protection: IP 21
› Approval: CE compliant
› Colors: white RAL 9016
› Surface Temperature: 120 °C (maximal)
› Device/Installation depth: 22/52 mm
› Factory warranty: 5 Years
Type Output (W) Measurements (mm) Weight (kg)
Length Height
LAVA-GLAS2-250-DYL 180 500 630 10
LAVA-GLAS2-500-DYL 350 900 630 15
LAVA-GLAS2-750-DYL 500 1300 630 23
LAVA-GLAS2-1000-DYL 700 1600 630 33
Type Output (W) Measurements (mm) Weight (kg)
Length Height
LAVA-GLAS2-250-IMAGE 180 500 630 10
LAVA-GLAS2-500-IMAGE 350 900 630 15
LAVA-GLAS2-750-IMAGE 500 1300 630 23
LAVA-GLAS2-1000-IMAGE 700 1600 630 33
TECHNICAL DATA LAVA®GLAS 2.0-DESIGN YOUR LAVA®
TECHNICAL DATA LAVA®GLAS 2.0-IMAGE
TECHNICAL DATA LAVA®BASIC-DM
Type Order no. Control system Output (W) Dimensions (mm) Weight
(kg)
Length Height
LAVA-BASIC-350DM 39692 none 350 620 620 7.5
LAVA-BASIC-500DM 39622 none 500 900 620 12
LAVA-BASIC-750DM 39623 none 750 1245 620 16
LAVA-BASIC-1000DM 39624 none 1000 1600 620 21
LAVA-BASIC-1500DM 39723 none 1500 1245 1245 32
14
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

› Voltage: 230 V
› Surface: 6 mm ESG safety glass
› Protection: IP X4
› Approval: CE compliant
› Colors: pure white, white-green
› Surface Temperature: 120 °C (maximal)
› Device/Installation depth: 31/62 mm
› Factory warranty: 5 Years
ACCESSORIES
TECHNICAL DATA LAVA®GLAS-DM
Model Order
no.
Output
(W) Length Height
LAVA-GLAS-500DM-PW 38819 500 900 630
LAVA-GLAS-750DM-PW 38820 750 1300 630
LAVA-GLAS-1000DM-PW 38821 1000 1600 630
LAVA®GLAS-DM, pure white (PW)
Model Order
no.
Output
(W) Length Height
LAVA-GLAS-500DM-WG 38816 500 900 630
LAVA-GLAS-750DM-WG 38817 750 1300 630
LAVA-GLAS-1000DM-WG 38818 1000 1600 630
LAVA®GLAS-DM, white-green (WG)
Typ Beschreibung
LAVA-R Thermostat with plug, for all LAVA®2.0, 5 - 35 °C, 16 A, step switch 40/65 °C, eNEXHO ready
LAVA-F Radio receiver with plug, 16 A, for mounting on the rear panel of the LAVA®2.0
ET-11A Radio room thermostat, LCD display
ET-12A Radio room thermostat, LCD display with clock and week program
eNEXHO-NT Internet module for external access using smartphone or tablet over Wlan
eNEXHO-CR Radio-controlled data bus - Power Actuator, 868 MHz, 230V, 16 A, On/Off
LAVA-Halti-50-EO Polished stainless steel towel rail for LAVA-250 | 600 | 800, Width: 50 cm
LAVA-Halti-63-EO Polished stainless steel towel rail for LAVA-500 | 750 | 1000, Width: 63 cm
LAVA-STAND Steel stand for up to 2 LAVA®500 / 750 / 1000 W horizontally mounted
15
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER

Device does not heat:
› Fuse has blown or broken?
› External supply switch is turned in?
› Temperature of the thermostat set is smaller than the actual
room temperature?
Radiant heat is too low:
› Distance between glass radiation heater and person is too
large?
› Device size too small?
› Objects between the glass-radiation heater and person
placed?
GENERAL WARRANTY CONDITIONS
Graphic: manufacturing number
Made in Austria
LAVA-BASIC2-250
250 W | IP X4
230 V | 50 Hz
8 kg
Landesstraße 16
A-5302 Henndorf Do not cover!
Nicht abdecken!
Typenschild_LAVA_all_2015.indd 1 11.05.2015 15:45:45
Made in Austria
LAVA-GLAS2-1000
1000 W | IP X4
230 V | 50 Hz
33 kg
Landesstraße 16
A-5302 Henndorf Do not cover!
Nicht abdecken!
Typenschild_LAVA_all_2015.indd 10 11.05.2015 15:45:47
On the rating plate the type-specic technical data are given. You can nd the rating plate, depending on the arrangement of ver-
tical or horizontal, on top or on the left of the unit.
Graphic: Nameplate LAVA®BASIC
Made in Austria
LAVA-BASIC2-250
250 W | IP X4
230 V | 50 Hz
8 kg
Landesstraße 16
A-5302 Henndorf Do not cover!
Nicht abdecken!
Typenschild_LAVA_all_2015.indd 1 11.05.2015 15:45:45
Graphic: Nameplate LAVA®CERAMIC
Made in Austria
LAVA-CERAMIC-1000
1000 W | IP X4
230 V | 50 Hz
33 kg
Landesstraße 16
A-5302 Henndorf Do not cover!
Nicht abdecken!
Typenschild_LAVA_all_2015.indd 22 11.05.2015 15:45:49
Graphic: Nameplate LAVA®GLAS
Made in Austria
LAVA-GLAS2-500
500 W | IP X4
230 V | 50 Hz
15 kg
Landesstraße 16
A-5302 Henndorf
Do not cover!
Nicht abdecken!
Typenschild_LAVA_all_2015.indd 6 11.05.2015 15:45:46
Made in Austria
LAVA-BASIC2-250
250 W | IP X4
230 V | 50 Hz
8 kg
Landesstraße 16
A-5302 Henndorf
Do not cover!
Nicht abdecken!
Typenschild_LAVA_all_2015.indd 1 11.05.2015 15:45:45
EQUIPMENT SIGNS
TROUBLESHOOTING
Dear Customer,
please refer to our terms and conditions common paradigm. In warranty cases inform your dealer directly and he or she will help
you due to country-specic legal claims.
Stand:11/2016
ETHERMA
Elektrowärme GmbH
Landesstraße 16
A-5302 Henndorf
Tel.: [phone] | 76 77
Fax: [phone] | 76 66
Web: www.etherma.com
Mail: of[email protected]
ETHERMA
Deutschland GmbH
Bahnhofstraße 40
D-48599 Gronau
Tel.: [phone] | 81 97 00
Fax: [phone] | 81 97 029
Web: www.etherma.com
Mail: of[email protected]om
WARNING: Electrical and electronic appliances often contain prescious materials. But they can also contain harmful substances that were
necessary for their function and safety. They can harm the environment if disposed or mishandled. Please help to protect our environment!
Therefore do not dispose of this device in the residual waste. Dispose of this unit in accordance with local regulations. Dispose of the packaging
materials, replacement parts or equipment parts properly.
ATTENTION: Packaging materials, replacement parts and equipment to be scrapped or equipment parts must be disposed pro-
perly.
INSTALLATION AND USAGE INSTRUCTION | LAVA®DESIGN INFRARED HEATER