EtherWAN EX78000 Series User manual

Copyright 2017 EtherWAN Systems, Inc. Page 1
All Rights Reserved
EX78000
8/15/2017
EX78000 Series Hardened Managed Ethernet Switch
Installation Guide
1 Unpacking
Unpack the items. Your package should include:
One EX78000 Series hardened managed switch
One CD containing this user’s guide
If items are missing or damaged, notify your
EtherWAN representative. If possible, save the
carton and packing material in case you need to
ship or store the switch in the future.
2 Equipment Needed
Category 5 or better cable for RJ-45 ports
Appropriate fiber cables for fiber ports
Appropriate SFP cable for SFP ports
Personal computer with a DB-9 straight cable
3 Select a Location
Installation: Wall-mount, wall (in an enclosure or
industrial panel).
Identify a power source within 6 feet (1.8
meters).
Choose a dry area with ambient temperature
between -40 and 75ºC (-40 and 167ºF).
Be sure there is adequate airflow.
4 Connect to the Data Ports
Depending on the model, your switch can have
the following ports:
4 or 8 10/100BASE-TX Power over Ethernet (PoE)
ports
0, 2, or 4 100BASE-FX ports
2 Gigabit ports
10/100BASE-TX (PoE) and
10/100/1000BASE-TX Ports
Ports that support Power over Ethernet provide
power to networked devices such as IP Phones,
Wireless LAN Access Points, and IP security
cameras with a power budget of 240 watts
maximum.
2 100/1000BASE SFP Slots
SFP transceivers can be installed directly into
SFP slots. Ensure that the same type of
transceiver is used at both ends of the link and
that the correct type of fiber cable is used.
100BASE-FX Fiber Ports
Some models are equipped with fiber optic ports
accepting SC & ST connectors instead of SFP
slots. Select an appropriate cable type according
to your distance and transmission rate needs.
5 Apply Power
The switch has a 52-57VDC terminal block for
power input. Only one power input is required to
operate the switch. However, redundant power
supply functionality is supported.
IEEE802.3at: up to 30W/port, 52-57VDC
60 Watts/port, 52-57VDC
52VDC: 4.85A
57VDC: 4.45A
Note: Only use qualified power supply, either
SELV or double insulated per UL 60950 or UL
61010-1 or UL 61010-2-201 standards.
Device power consumption: 10.4W Max. (Without
PoE)
PoE power budget: 240W Max.
W70G-EX780V2Q1

Copyright 2017 EtherWAN Systems, Inc. Page 2
All Rights Reserved
EX78000
8/15/2017
W70G-EX780V2Q1
EX78000 Series Hardened Managed Ethernet Switch
Installation Guide
Terminal Block
The switch provides two power inputs on a 52-
57VDC terminal block. Only one power input is
required to operate the switch. The terminal
block has 5 terminal posts.
Pin
Description
Power 1

52-57VDC

Power Ground
Power 2

52-57VDC

Power Ground
Earth Terminal
Relay Output Rating
0.5A @ 48VDC
Relay Output Alarm
The switch provides relay output contacts for
signaling of a user-defined power or port failure.
The relay output can be connected to an alarm
signaling device. Current is 0.5A at 48VDC.
Power-Up Sequence
When you apply power:
All Link/ACT LEDs blink momentarily.
The Power 1 LED goes ON.
LEDs for every port connected to a device flash,
as the switch conducts a Power On Self-Test.
6 Console Configuration
Connect to the switch console by connecting a
DB-9 cable to the console port of the switch and
to the serial port of a computer running a
terminal emulation application (such as
Hyperterminal or Putty).
Configuration settings of the terminal-emulator:
Baud rate: 115,200bps, Data bits: 8, Parity: none,
Stop bit: 1, Flow control: none.
The default login name is “root,” no password.
7 Web Configuration
Log in to the switch by launching a web browser
and entering 192.168.1.10 in the address bar.
Enter the default login ID: root (no password)
and click “Login.” The system information screen
will display as shown below.
8 Other information
DIN-Rail assembly, startup, and dismantling
Assembly: Place the Switch on the DIN rail
from above using the slot. Push the front of
the Switch toward the mounting surface until
it audibly snaps into place.
Startup: Connect the supply voltage to start
the switch via the terminal block.
Dismantling: Pull out the lower edge and then
remove the Switch from the DIN rail.
Power wiring information:
Use cable type - AWG (American Wire Gauge) 18-
24 and the corresponding pin type cable
terminals. Tighten terminal screws with a torque
value of 1.7 lb-in. Do not use excessive force
when fixing wiring.
The rating of the power wire used must
be at least 105°C.
If the equipment is used in a manner not
specified by the manufacturer, the protection
provided by the equipment may be impaired.
The Ethernet switch should be mounted in an
industrial control panel with ambient
temperature not exceeding 75 degrees C.
Manufacturer information:
ETHERWAN SYSTEMS, INC.
4F-7, No. 79, Sec. 1, Xintai 5th Road, Xizhi
District, New Taipei City 221, Taiwan
3 Normal Open |2 Ground |1 Normal close