Event Lighting EL1000RGB User manual

EL1000RGB
1000 mW RGB Mini Animation Laser
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0

www.event-lighting.com.au
1
Safety Instructions
Warning
• Do not open this fixture, there are no user serviceable parts inside. Risk of electric shock.
• Do not look directly at the light source.
• Avoid contact with the unit during operation, as the housing may become hot. Allow the
fixture to cool for at least 15 minutes after turning off before touching.
• Install this fixture in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
• Do not operate this fixture, or connect this device to power, within 50cm of any flammable
material.
• Use a safety chain when mounting this fixture overhead.
• Do not operate this fixture outdoors where excessive dust, heat, water or humidity may
affect it.
• Do not operate this fixture if the housing, lenses, or cables appear damaged.
• Do not connect this fixture to a dimmer or rheostat.
• Do not operate this fixture at temperatures higher than 40°C (104°F).
• Only connect this fixture to a grounded and protected circuit.
• Only use the hanging bracket to carry this fixture.
• Stop using this fixture immediately if a serious operating problem becomes apparent.
Laser Warning
Laser light can cause instant eye injury if the product is not set up and used correctly. Avoid
direct eye contact with the laser light. Never intentionally expose your eyes or others to direct
laser light. This laser product can potentially cause instant eye damage or blindness if laser light
directly strikes the eyes. The heat from a laser cannot be felt, but it can still injure or cause
blindness. This can occur even with very small amounts of exposure at a long distance.
This product contains a Class 3B Laser. It is critical to prevent the possibility of ANY direct eye
exposure.
• Do not operate the laser without reading and understanding the safety information
contained in this manual.
• Test the product before public use to ensure the lasers are functioning correctly, and that
eye exposure is impossible.
• Do not assume exposure to an individual laser beam is safe.
• Do not assume a moving laser light is safe. Eye injury can occur instantly.
• EL1000RGB must be installed at least 3 metres above ground level and 3 metres from
any person. See the Product Installation section for details.

www.event-lighting.com.au
2
• Do not point the laser at any person or animal.
• Do not point the laser towards any area where people could be exposed to them.
• Do not point the laser towards any reflective surfaces, such as windows, mirrors and
shiny metals. Laser reflections can also cause injury.
• Do not point the laser towards any area where you or the operator do not know where the
beams are being directed.
• Do not point the laser into the sky or towards any aircraft.
• The legal requirements for operating laser products vary between jurisdictions. It is the
user’s responsibility to meet the legal requirements in the location/country of use.
Product Installation
• EL1000RGB can be mounted in many orientations, provided each individual device is
secured by the use of the correct mounting bracket.
• This device should be directed above the heads of people. Do not direct this device
towards the line of sight of anyone. Refer to the diagram below.
• A minimum of 3 meters vertical separation is required between the floor and the laser
device.
• A minimum of 3 metres horizontal separation is required between the laser light and any
person or public space.
• Use a safety chain when mounting EL1000RGB overhead.

www.event-lighting.com.au
3
Menu
Menu
Values
Function
Addr
1-512
Set DMX address
AUTO
0-9
Auto mode 0-9
SOUN
0-9
Sound active mode 0-9
VERSION
Ver1.1
Software version
DMX Chart
Channel
Function
Min DMX
Max DMX
Description
1
Laser
on/off
0
9
Laser off
10
255
Laser on
2
Colour
control
0
69
Static colours, white-red-blue-pink-cyan-yellow-
green
70
79
Colour change (speed controlled by Ch. 3)
80
89
Default colour (speed controlled by Ch. 3)
90
99
Rainbow colour (speed controlled by Ch. 3)
100
224
Segment colour, 5 data stepping (speed
controlled by Ch. 3)
225
229
Dynamic colour 1 (speed controlled by Ch. 3)
230
234
Dynamic colour 2 (speed controlled by Ch. 3)
235
239
Dynamic colour 3 (speed controlled by Ch. 3)
240
244
Dynamic colour 4 (speed controlled by Ch. 3)
245
249
Dynamic colour 5 (speed controlled by Ch. 3)
250
255
Dynamic colour 6 (speed controlled by Ch. 3)
3
Colour
speed
0
9
No function
10
127
Clockwise, slow to fast
128
255
Anticlockwise, slow to fast
4
Pattern
option
0
255
Pattern option
5
Patterns
group
optoin
0
50
Inner patterns group 1
51
101
Inner patterns group 2
102
152
Inner patterns group 3
153
203
Inner patterns group 4
204
255
Inner patterns group 5
6
Pattern
size
0
255
Manual pattern size option
7
Pattern
auto
zoom
0
15
Manual zoom
16
55
Zoom, small to large, speed slow to fast
56
95
Zoom, large to small, speed slow to fast
96
135
Cycle zoom large to small, speed slow to fast

www.event-lighting.com.au
4
136
175
Cycle zoom 1, speed slow to fast
176
215
Cycle zoom 2, speed slow to fast
216
255
Cycle zoom 3, speed slow to fast
8
Centre
rotation
0
127
Rotation angle
128
191
Clockwise rotation speed
192
255
Anticlockwise rotation speed
9
Horizontal
rotation
0
127
Flip horizontal location
128
255
Flip horizontal speed
10
Vertical
rotation
0
127
Flip vertical location
128
255
Flip vertical speed
11
Horizontal
remove
0
127
Horizontal location
128
255
Horizontal auto location, speed slow to fast
12
Verical
remove
0
127
Vertical rotation
128
255
Vertical auto location, speed slow to fast
13
Wave
0
9
No function
10
255
Wave range and speed (range small to large,
speed slow to fast)
14
Patterns
drawing
0
1
No function
2
63
Drawing by manual adjustment 1
64
127
Drawing by manual adjustment 2
128
153
Automatic drawing (increasing)
154
179
Automatic drawing (decreasing)
180
205
Automatic drawing (increasing to decreasing,
reverse)
206
255
Automatic drawing (increasing to decreasing)
15
Inner
dynamic
effect
0
2
No function
3
229
Single group dynamic effect, speed and colour
controlled by Ch. 16
230
249
Random auto effect, speed and colour
controlled by Ch. 16
16
Inner
dynamic
effect
speed
0
127
Inner effect speed, fast to slow, colour
determined by inner program
128
255
Inner effect speed, fast to slow, colour
determined by DMX

www.event-lighting.com.au
5
Technical Specifications
• Light source: 1000mW RGB laser
• Total power: 22W
• Control mode: Auto/Sound/DMX512/Master-slave/ILDA
• Channels：16CH
• Scanning system: 15Kpps Scanner, ±30º
• 51 internal patterns for show
• Surface temp: Tb=45ºC ( when the environment temp is 30ºC)
• Working temp: 10ºC--65ºC
• Modulation: TTL
• Input voltage: AC100-240V, 50/60Hz
• Fuse: BGDP ￠5x20mm 250VAC F2A
• Product size: 188*193*173mm
• Weight: 2.4Kg
Warranty
Please refer to your local dealer or contact Event Lighting.