Event Lighting PRO PAR PAR6X12OB User manual

PRO PAR
Model No. PAR6X12OB
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
Ver 1.0

www.event-lighting.com.au
1
CONTENTS
Safety Instructions
- Power input & power Linking
Product Installation
- Fuse replacement
Diagrams
- Dimensions
Control Board Operation
- Menu map
- Static colour mode chart
DMX chart
Technical specifications
Warranty

www.event-lighting.com.au
2
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

www.event-lighting.com.au
3
Lux Chart
Dimensions

www.event-lighting.com.au
4
CONTROL BOARD OPERATION
Menu Map
-> - Select DMX address for 6 ch mode
-> - Select DMX address for 10 ch mode
-> or Set dimming speed (SL: slow / FA: fast)
-> or
When lost DMX signal,
ho: keep the last DMX signal state
OF: blackout
-> or Switch on/off wireless DMX control
-> or Switch on/off IR remote control
-> - Set red colour intensity
-> - Set green colour intensity
-> - Set blue colour intensity
-> - Set white colour intensity
-> - Set amber colour intensity
-> - Set UV colour intensity
-> - Display IR control brightness level
-> - Set strobe speed
-> -
Select 15 static colour modes, see chart: Static
colour mode
-> - Select 16 speed of auto colour switch mode
-> - Select 16 speed of auto colour fading mode
-> - Select 16 speed of auto colour pulse out mode
-> -
Select sound active mode with different sound
sensitive level

www.event-lighting.com.au
5
Display current temperature
Display version number
-> or Reset
Static colour mode
Value: Function:
C1 R
C2 G
C3 R + G
C4 B
C5 B + R + UV
C6 G + B
C7 R + G + B + A + UV
C8 W
C9 R + W
C10 G + W
C11 R + A
C12 B + W + UV
C13 R + B + W + UV
C14 G + B + W
C15 R + G + B + W + A + UV
Wireless DMX mode
Set up wireless DMX
The fixture needs to be paired from the wireless DMX transmitter. Follow below steps to pair.
Step 1: Connect the DMX512 controller to the wireless DMX transmitter.
Step 2: Switch on the PAR6x12OB, turn on the wireless DMX control on from control panel ‘rfon’
Step 3: Set the PAR6x12OB to DMX mode. (AXXX or dXXX)
Step 4: Switch off the PAR6x12OB. Press and hold the ‘DMX select’ button whilst switching on the fixture. Once the
fixture turns on the ‘wireless status’ light will be lit white and the unit will be in ‘setup mode’.
Step 5: The ‘wireless indicator’ will be lit to a specific colour to indicate the protocol being used for the transmission as
shown in TABLE1. Pressing the button will cycle through the colours and once you want to set the protocol pressing the
button for more than 1s will save the protocol. The transmitters, receivers and transceivers will remember the protocol
used even after a power cycle with their built in memory chip.
Now you need to setup as for WDMX mode or EL mode

www.event-lighting.com.au
6
Protocols TABLE1
Colour Protocol
Red ELDMX Transmit and receive
Green W-DMX Receive
Blue W-DMX G3 Transmit
Yellow W-DMX G4 Transmit
Purple GZ Receive* (*Receiver Only)
Using W-DMX mode
Transmitters
Pressing the button momentarily will connect to all unconnected receivers in the coverage area.
Pressing the button for more than 3s will disconnect all receivers in the coverage area.
Receivers
Pressing the button for more than 3s will disconnect the device with a transmitter.
NOTE:
The colour of the light will indicate the group as shown in Table2.
The receiver will not connect with a new transmitter unless it is disconnected first.
W-DMX Status Indicators TABLE2
Protocol Action Description
W-DMX Receive White No connection
Red Deleting Connection
Red Fast Flash Connection Lost
Green Fast Flash Connecting to Transmitter
Green Slow Flash Connected but no DMX signal
Green Connected with DMX signal
W-DMX Transmit Red Deleting All Receivers
Blue Fast Flash Connecting with the receivers
Blue Slow Flash No DMX input
Blue Transmitting DMX
Using EL wireless DMX mode
Changing Channel Group
Pressing the Button will show you the current channel group being used and pressing it again will cycle through the
groups. The colour of the light will indicate the group as shown in Table3.
Status Indicators TABLE3
Protocol Action Description
ELDMX / GZ Solid Colour (Red, Green, Blue,
Yellow, Cyan, Magenta, White*)
1 of the 7* colour groups
(*7th white only in GZ mode, 6 in WIDMX modes)
Flashing Red Transmitting DMX
Flashing Green Receiving DMX

www.event-lighting.com.au
7
IR remote control mode
-You must switch off wireless DMX function, select .
-Select , then use IR remote to switch on IR remote control mode.
Key Function Display
Switch on/off IR function
to
or
your last setting
Pressing <blackout> button to switch on
the fixture IR function, fixture will go to
CC12 auto colour switch mode or your
last setting
Pressing <blackout> button when unit
under IR mode, fixture will blackout and
on IR standby mode
Select auto colour switch mode (CC)
or auto colour pulse out mode (CP)
with different speed
between
Using <Auto> button to select CC or CP
mode, using to change
speed.
Select sound active mode (SU) with
different sensitivity level
Pressing <SOUND> button to select SU
mode, using to change
sensitivity level
Select auto colour fade mode (dE)
with different speed
Pressing <FADE> button to select dE
mode, using to change
speed.
Select manual colour mode
to
Pressing <MANUAL> button to entry
manual colour mode
Using
button
to cycle though 20% change of intensity
of each colour separately.
to
Pressing <MANUAL> button to quit
manual colour mode, fixture will blackout

www.event-lighting.com.au
8
Select intensity of LED full on mode
to
Pressing <%> button to cycle though
10% change of intensity on static colour
(R255+G255+B255+W255+A255+U255)
mode.
Select intensity of static colour
(R255+G255+B255+W255+A255+U
255)
to
Using to change intensity
Select intensity of static colour (R255)
to
Using to change intensity
Select intensity of static colour
(UV50+R255)
to
Using to change intensity
Select intensity of static colour
(R255+G50)
to
Using to change intensity
Select intensity of static colour
(G255)
to
Using to change intensity
Select intensity of static colour
(G160+B255+UV100)
to
Using to change intensity
Select intensity of static colour
(B255+UV50)
to
Using to change intensity
Select intensity of static colour
(R50+B255+UV200)
to
Using to change intensity
Select intensity of static colour
(R255+B150+UV255)
to
Using to change intensity
Select intensity of static colour
(R255+B20+A200)
to
Using to change intensity
Reset factory default setting
to
No function
Add strobe effect on CC, CP, SU, dE,
dl and static colour mode.
No change Pressing <STROBE> button to cycle
though 1/8 change of strobe speed

www.event-lighting.com.au
9
DMX Chart
6 channels Mode
Channel Value Function
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 White: 0% ~ 100%
5 000-255 Amber: 0% ~ 100%
6 000-255 UV: 0% ~ 100%

www.event-lighting.com.au
10
10 channels Mode
Channel Value Function
1 000-255 Red: 0% ~ 100%
2 000-255 Green: 0% ~ 100%
3 000-255 Blue: 0% ~ 100%
4 000-255 White: 0% ~ 100%
5 000-255 Amber: 0% ~ 100%
6 000-255 UV: 0% ~ 100%
7 000-255 Master Dimmer 0% ~ 100%
8 000-255 Strobe (slow-fast)
9 000-050 No function
051-100 Select 15 Static colour mode (CL), colour have been controlled by ch10
101-150 Select Auto colour switching modes (CC), program speed have been
controlled by ch10
151-200 Select Auto colour fade mode (dE), program speed have been controlled
by ch10
201-250 Select Auto colour pulse mode (CP), program speed have been controlled
by ch10
251-255 Select Sound active mode (SU), sound sensitivity level have been
controlled by ch10
10
(Ch9 set 051-100)
000-015 No function
016-031 R
032-047 G
048-063 R + G
064-079 B
080-095 B + R + UV
096-111 G + B
112-127 R + G + B + A + UV
128-143 W
144-159 R + W
160-175 G + W
176-191 R + A
192-207 B + W + UV
208-223 R + B + W + UV
224-239 G + B + W
240-255 R + G + B + W + A + UV
10
(Ch9 set 101-250)
000-255 Select auto run speed for (CC, dE and CP) from slow to fast
10
(Ch9 set 251-255)
000-255 Select sound sensitivity level for sound active mode (SU) form low to high

www.event-lighting.com.au
11
TECHNICAL SPECIFICATIONS
Power
Input Voltage: 100~240V AC, 50/60 Hz
Power Consumption: 72W
Connection: Seetronic® Outdoor Powerkon input connection
Photometric
Light Source: 6pcs 6-in-1 RGBWAU 12W LED
Beam Angle: 40°
PWM: 20,000 Hz
LED Lifespan: 50,000 hours
Effects
Dimming: 0~100%
Strobe: 0~20 Hz
Control
Protocol: DMX512, Wireless DMX
DMX Channels: 6 / 10
Built-in Programming: Yes
Display: 4-button & 4-digit LED display control panel
Cooling: Fanless
Battery
Approx. 4 hours full colour
Approx. 20 hours single color at auto run
Housing
Materials: Die-cast Aluminum
Finishing: Matte black
IP rating: IP65
Net Weight: 3 kg
Overall Size: 240 x 165 x 210 mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.