Event Lighting PARRGBW12x8 User manual

1
Propar
Model No. PARRGBW12x8, PARRGBWAU12x12
PARRGBW5x8, PARRGBWAU5x12
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this
manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any
errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.
www.event-lighting.com.au
V1.1

2
CONTENTS
Safety Instructions
- Power Input & Power Linking
Product Installation
- Fuse replacement
Diagrams
- Lux Chart
- Dimensions
Control Board Operation
- DMX Addressing
- DMX Modes
- Dimmer Speed Setting
- Sound Mode
- Setting Static Colors
- Manual Color Mode
- Automatic Mode
- Master/slave Operation
DMX Values
Technical Specifications
Warranty

3
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104°F (40°C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this number.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by the use of correct
mounting bracket.
Use a safety chain when mounting this device overhead.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

4
Lux Chart
Dimensions

5
CONTROL BOARD OPERATION
Display Function
DMX Addr To set DMX address
DMX Chan
To set DMX channel modes:
RGBW Models - CH10, CH06, CH04
RGBWAU Models - Ch12, CH08, CH06
Dimmer C To set dimmer speeds: <01>, <02>, <03>, <04>
Sound To set sound active mode and the sensitivity (Sen000 ~ Sen100)
Static C
To set static colors: Static Color
RGBW Models - R, G, B, W, GB, RB, RG, RGB, RW, GW, BW, RGW, RBW, GBW, RGBW
RGBWAU Models - R,G,B,W,A,U,GB,RB,RG,RGB,RW,GW,BW,WA,,RA,GA,BA,RGW, RBW, GBW,
RGBW,GBA,BWA,RGA,GWA,RWA,RGBA,GBWA,RBWA,RGWA,RGBQA,RU,GU,AU,RAU,RGBWAU
Manual C To set user mode intensity of each colour separately for color mixing and strobe rate
Auto Program To set built-in automatic programs: Pr 01 ~ Pr 05 and speeds Sp000 ~Sp100
Mas/Sla To set Master/Slave modes
DMX Addressing:
After select the "DMX Addr" and press Enter, then use Up and Down to set the desired DMX address (001~512),
press "Enter" again to confirm.
DMX Modes (Three DMX modes option)
After select the "DMX Chan" and press Enter, then use Up and Down to set the desired
DMX mode (CH10 / CH06 / CH04),
press "Enter" again to confirm.
Dimmer Speed Setting:
After select the "Dimmer C" and press Enter, then use Up and Down to set the desired dimmer curves (01, 02, 03, 04),
press "Enter" again to confirm.
Sound Mode
Entered "Sound" mode, use <UP> and <DOWN> to set the sensitivity Sen000 ~ Sen100, press Enter to confirm.
Manual Color Mode
This mode allows the user set intensity of each colour separately to get endless color mixing from the control
board without DMX controller to set the device to run strobe desired.
Entered "Manual C" mode, use <UP> and <DOWN> to select the Colours intensity or "S" for strobe
Use <UP> and <DOWN> to set the colors intensity values " 000 ~ 255" or Strobe speed values "S000 ~ S100"
(Freeze, Slow ~ Fast), then press "Enter" to confirm.

6
Setting Static Colors
Entered "Static C" mode, you can select the desired solid color via the UP or DOWN buttons and confirm by Enter
Mode:
RGBW Models RGBWAU Models
Value: Function:
CL 01 Red
CL 02 Green
CL 03 Blue
CL 04 White
CL 05 Amber
CL 06 UV
CL 07 Green + Blue
CL 08 Red + Green
CL 09 Red + Blue
CL 10 Red + White
CL 11 Green + White
CL 12 Blue + White
CL 13 White + Amber
CL 14 Red + Amber
CL 15 Green + Amber
CL 16 Blue + Amber
CL 17 Red +Green + Blue
CL 18 Red + Green + White
CL 19 Red + Blue + White
CL 20 Green + Blue + White
CL 21 Green + Blue + Amber
CL 22 Blue + White + Amber
CL 23 Red + Green + Amber
CL 24 Green + White + Amber
CL 25 Red + White + Amber
CL 26 Red + Green + Blue + Amber
CL 27 Green + Blue + White + Amber
CL 28 Red + Green + Blue + White
CL 29 Red + Blue + White + Amber
CL 30 Red + Green + White + Amber
CL 31 Red + Green + Blue + White + Amber
CL 32 Red + UV
CL 33 Green + UV
CL 34 Amber + UV
CL 35 Red + Amber + UV
CL 36 Red + Green + Blue + White + Amber + UV
Static Colour
Value: Function:
R Red
G Green
B Blue
W White
GB Green + Blue
RB Red + Blue
RG Red + Green
RGB Red + Green + Blue
RW Red + White
GW Green + White
BW Blue + White
RGW Red + Green + White
RBW Red + Blue + White
GBW Green + Blue + White
RGBW Red + Green +
Blue + White

7
Automatic Mode
This fixture has a built-in automatic program.
Entered "Auto Pro" mode, use <UP> and <DOWN> to select the built-in programs "Pr 01 ~ Pr 05"
then press the "Enter" to confirm.
Use <UP> and <DOWN> to select the operating speed of the program(Value:S000 ~ S100, Freeze, Slow ~ Fast),
press "Enter" to confirm.
Mode:
Auto Program
Value: Function:
Pr 01 RGBW Model : R G B W colour switching
RGBWAU Model R G B W A U colour switching
Pr 02 RGBW Model : 15 colour switching
RGBWAU Model 36 colour switching
Pr 03 RGBW Model : R G B W colour fading
RGBWAU Model R G B W A U colour fading
Pr 04 RGBW Model : 15 colour fading
RGBWAU Model 36 colour fading
Pr 05 Colour Macros Fading
Master/Slave Operation
1) Set the master fixture to one of the standalone operating modes: automatic, sound, static
color or manual color modes
2) Set the slaves, entered "Mas/Sla" mode, set to <S>, press Enter.
"Slave " will display.
DMX VALUES:
4/6 Channels Mode:
RGBW RGBWAU VALUE FUNCTION
1 1 000-255 Red: 0% ~ 100%
2 2 000-255 Green: 0% ~ 100%
3 3 000-255 Blue: 0% ~ 100%
4 4 000-255 White: 0% ~ 100%
5 000-255 Amber: 0% ~ 100%
6 000-255 UV: 0% ~ 100%
6/8 Channels Mode:
RGBW RGBWAU VALUE FUNCTION
1 1 000-255 Red 0% ~ 100%
2 2 000-255 Green 0% ~ 100%
3 3 000-255 Blue 0% ~ 100%
4 4 000-255 White 0% ~ 100%
5 000-255 Amber 0% ~ 100%
6 000-255 UV 0% ~ 100%
5 7 000-255 Master DIMMER 0% ~ 100%
6 8
000-009 No function
010-019 Sound Active
020-255 Strobe : Slow ~ Fast (1~30Hz)

8
10/12 Channels Mode:
RGBW RGBWAU VALUE FUNCTION
1 1 000-255 Red 0% ~ 100%
2 2 000-255 Green 0% ~ 100%
3 3 000-255 Blue 0% ~ 100%
4 4 000-255 White 0% ~ 100%
5 000-255 Amber 0% ~ 100%
6 000-255 UV 0% ~ 100%
5 7 000-255 Master DIMMER 0% ~ 100%
6 8
000-009 Strobe OFF
010-255 Strobe (slow-fast 1-30Hz)
7 9
000-019 No Function
020-039
RED 100% / GREEN 0% ~
100% / BLUE 0%
040-059
RED 100% ~ 0% / GREEN
100% / BLUE 0%
060-079
RED 0% / GREEN 100% / BLUE
0% ~ 100%
080-099
RED 0% / GREEN 100% ~ 0%
/ BLUE 100%
100-119
RED 0% ~ 100% / GREEN 0%
/ BLUE 100%
120-139
RED 100% / GREEN 0% / BLUE
100% ~ 0%
140-159
RED 100% / GREEN 0%
~100% / BLUE 0% ~ 100%
160-179
RED 100%~ 0% / GREEN 100%
~ 0% / BLUE 100%
180-200
RED 100% / GREEN 100% /
BLUE 100% /WHITE 100%
201-204 Color Temperature 1 WARM
205-209 Color Temperature 2
210-214 Color Temperature 3
215-219 Color Temperature 4
220-224 Color Temperature 5
225-229 Color Temperature 6
230-234 Color Temperature 7
235-239 Color Temperature 8
240-244 Color Temperature 9
245-249 Color Temperature 10 COOL
250-255 Color Temperature 11
8 10
000-009 No Function
010-057 Auto Program 1
Single colors
switching

9
058-106 Auto Program 2
mixed colors
switching
107-155 Auto Program 3
Single colors
fading
156-204 Auto Program 4
Mixed colors
Fading
205-255 Auto Program 5
Color Macros
Fading
9 11 000-255
Speed of Auto Programs (Slow ~
Fast)
10 12
000-009
Use the dimmer of control board
setting
010-069 Linear dimmer
070-130 Non-linear dimmer 1
131-191 Non-linear dimmer 2
192-255 Non-linear dimmer 3
TECHNICAL
SPECIFICATIONS
Model PARRGBW 5x8 PARRGBWAU5X12 PARRGBW 12x8 PARRGBWAU12X12
Dimensions and Weight
LxWxH (mm) 96x213x227 98x263x292.5
Weight (kg) 1.9 3.2
Power
Power Supply 100~240V AC, 50/60 Hz
Power Consumption (w) 40 50 98 120
Fuse T 1 A, 250 V T 2 A, 250 V
LED 5pcs 8W
Quad-color RGBW
5pcs 12W
RGBWA+UV 6 in 1
12pcs 8W
Quad-color RGBW
12pcs 12W
RGBWA+UV 6 in 1
Operation Modes DMX, Auto, Sound Active, Master/Slave, RGBW Manual Control
Mode, Static Colour Mod
Beam Angle 22°
Refresh Rate 2940Hz
DMX Channel 4,6, 10 channels 6.8,12 Channels 4, 6, 10 channels 6.8,12 Channels
Power Input IEC Neutrik Powercon IEC Neutrik Powercon
Power Output No Neutrik Powercon IEC Neutrik Powercon
LCD display with 4 buttons control board
Smooth electronic dimming with a 16-bit 4 Dimmer curve
Die-cast Aluminum Housing
Tempered glass front cover lens
Smart Cooling system without fan
Variable Speed Strobe Effect (1 – 30 Hz)
WARRANTY
Please refer to your local dealer or please contact Event Lighting.