Event Lighting LM6X15 User manual

LM6X15
6x15W LED WASH ZOOM HEAD
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to
change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting
for any clarification or information regarding this item.
www.event-lighting.com.au V1.0

2
www.event-lighting.com.au
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
•Do not look at the light source when the device is on.
•CAUTION: This unit's housing may be hot during and after operation.
•Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
•Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
•Use a safety chain when mounting this device overhead.
•Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
•Do not operate this device if the housing, lenses, or cables appear damaged.
•Do not connect this device to a dimmer or rheostat.
•ONLY connect this device to a grounded and protected circuit.
•ONLY use the hanging bracket to carry this device.
•In case of a serious operating problem, stop using immediately.
•The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.

3
www.event-lighting.com.au
Product Installation
This device can be mounted in many orientations provided each
individual device is secured by the use of correct mounting bracket.
Use a safety chain when mounting this device overhead.

4
www.event-lighting.com.au
Dimensions

5
www.event-lighting.com.au
Lux Chart

6
www.event-lighting.com.au
Menu operation
Menu –Move up a level.
Up –Move selection up one item.
Down –Move selection down one item.
Enter –Select / Mode down a level.

7
www.event-lighting.com.au
Menu
MENU
DESCRIPTION
DMX
Address
DMX
Address
A001~AXXX
DMX Address Setting
Auto Run
Auto Run
Program 1-8 | Master/Alone
Auto Run State
Music Run
Program 1-8 | Master/Alone
Music Control State
Reset
ALL
On/Off
Reset all motors
Pan/Tilt
On/Off
Reset pan/tilt motor
Zoom
On/Off
Reset zoom motor
Reverse
Pan
On/Off
Reverse pan
Reverse
Tilt
On/Off
Reverse tilt
Special
R Default
On/Off
Reset to default settings
Cal
Code (Password: 088)
Calibration code
Pan, Tilt, Colour, Gobo, Focus,
Prism
Calibrate the selected
channel
Temp.
XXX °C/°F
Current temperature
Manual
Ctrl.
Pan = XXX…
Manual control
Mic Sens.
0-99%
Microphone sensitivity
Limit Mode
Limit Mode Off/Centre/Right/Left
Select Edge or Corner range
DMX Mode
CH15
Mode
15 channel mode
CH13
Mode
13 channel mode
Scan
Degree
Pan
Degree
Pan 630°
Select Pan degree
(default 540°)
Pan 540°
Pan 360°
Tilt Degree
Tilt 270°
Select Tilt degree
(default 270°)
Tilt 180°
Tilt 90°
Version
V1.0 - vX.X
Software version

8
www.event-lighting.com.au
DMX Chart
Channel Mode
Min
DMX
Max
DMX
Name
Function
Standard
Basic
1
1
0
255
Dimmer
Dimmer 0%..100%
2
2
0
31
Shutter
Shutter closed
32
63
Shutter open
64
95
Strobe effect, slow to fast
96
127
Shutter open
128
159
Pulse effect, slow to fast
160
191
Shutter open
192
223
Random strobe effect, slow to
fast
224
255
shutter open
3
3
0
255
Pan
Pan movement
4
0
255
Pan-fine
Fine control of pan movement
5
4
0
255
Tilt
Tilt movement
6
0
255
Tilt-fine
Fine control of tilt movement
7
5
0
255
Zoom
In (near) to out (far)
8
6
0
225
Pan/tilt
function
Pan/tilt speed, fast to slow
226
235
Blackout during pan/tilt
functions
236
255
TBD
9
7
0
255
Red
Red 0..100%
10
8
0
255
Green
Green 0..100%
11
9
0
255
Blue
Blue 0..100%
12
10
0
255
White
White 0..100%
13
11
0
15
Macros
TBD
16
31
Red
32
47
Green
48
63
Blue
64
79
White
80
95
Red+Green
96
111
Red+Blue
112
127
Red+White
128
143
Green+Blue
144
159
Green+White
160
175
Blue+White
176
191
Red+Blue+Green
192
207
Red+Blue+Green+White
208
223
Jump Effect
224
239
Fading Effect
240
255
Pulse effect
14
12
0
255
Macro speed
Slow to fast

9
www.event-lighting.com.au
15
13
0
79
Special
functions
TBD
80
84
Reset all motors
85
87
Reset pan/tilt motor
88
96
TBD
97
99
Reset zoom motor
100
109
Internal program 1
110
119
Internal program 2
120
129
Internal program 3
130
139
Internal program 4
140
149
Internal program 5
150
159
Internal program 6
160
169
Internal program 7
170
179
Internal program 8
180
189
Internal sound program 1
190
199
Internal sound program 2
200
209
Internal sound program 3
210
219
Internal sound program 4
220
229
Internal sound program 5
230
239
Internal sound program 6
240
249
Internal sound program 7
250
255
Internal sound program 8
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive instructions
from the external controller. For independent control, each fixture must be assigned its unique address control channels.
For example, this device has two channel modes: 13/11, if we set the mode at standard 13 channels mode, and there
are several models need to be independently controlled, we just simply address first fixture at 1, and second fixture at 2,
third one at 3, etc.
- If the devices have the same address, they will behave synchronically.
- Display is flashing when no DMX signal is received.

10
www.event-lighting.com.au
More Functions
- Remote Device Management (RDM), which allows users to remotely control the device. Users can remotely
change the DMX address, reverse pan/tilt settings, check the device’ status, such as its temperature, power
consumption, fan speed, etc. Every device has a unique RDM code programmed during manufacture to facilitate
this function. It is not recommended for users to change this code.
- Software upgrade function via DMX cable. If there is any new firmware for this device, it can be upgraded simply via
a software upgrade box, without the need to change any mechanical parts. The upgrade box is not included in the
package, if you need any further assistance please contact your authorized dealer.
- Hibernation. The device will enter sleeping mode if activated after a period of disconnecting DMX signal to save
power and will wake immediately when the DMX signal is sent or received again.
- Display back-up communication IC. There is a back-up communication IC installed in the display PCB, so users
could replace at once if the original one is broken.
- Display flip. By pressing the up and down buttons for more than 3 seconds, the display will flip automatically, this
function is useful to read menu conveniently when device is hanged upside down.
Technical Specifications
Power
Input Voltage: 100~240V AC, 50/60 Hz
Power Consumption: 99W
Connection: Powercon in
Fuse: T2A, 250V
Photometric
Light Source: 6 pcs 15W RGBW LED
Beam Angle: 6° - 60°
Output: 8000lux @ 3M @ 6°
PWM: 800Hz
LED Lifespan: 50,000 hours
Effects
Dimming: 0~100%
Strobe: 0.6~22 Hz
Zoom: 6° - 60°
Movement 8 / 16 –bit
Pan: 540°
Tilt: 270°

11
www.event-lighting.com.au
Control
Protocol: DMX512
DMX Channels: 15 / 13
Interface: 3-pin XLR in & out
Built-in Programming: Yes
Sound Active: Yes
Display: 4-button 1.44 inch TFT display control panel
Cooling: Fan
Housing
Materials: Metal & Flame retardant ABS
Finishing: Matte black
IP rating: IP20
Net Weight: 4 kg
Overall Size: 243 x 151 x 278 mm
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.