Event Lighting PAR19X12L User manual

PAR19X12L
19x 12W LED RGBWAU Parcan with IR Remote
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0

www.event-lighting.com.au
1
Safety Instructions
Warning
• Do not open this device, there are no user serviceable parts inside. Risk of electric
shock.
• Do not look directly at the light source from close range.
• Avoid contact with the unit during operation, as the housing may become hot. Allow the
fixture to cool for at least 15 minutes after turning off before touching.
• Install this device in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
• Do not operate this device, or connect this device to power, within 50cm of any
flammable material.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors where excessive dust, heat, water, or humidity may
affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• Do not operate this device at temperatures higher than 40°C (104°F).
• Only connect this device to a grounded and protected circuit.
• Only use the hanging bracket to carry this device.
• Stop using this device immediately if a serious operating problem becomes apparent.
Coin/Button Cell Battery Safety Information
This product includes an IR remote that contains a coin/button cell battery. If the
battery is swallowed, it can cause severe internal burns and, in extreme cases, can
lead to death. Keep batteries away from children.
Product Installation
PAR19X12L can be mounted in many orientations, provided each individual device is secured by
the use of the correct mounting bracket. Use a safety chain when mounting PAR19X12L
overhead.

www.event-lighting.com.au
2
Dimensions
Lux Chart

www.event-lighting.com.au
3
Control Board Operation
Menu Map
->
-
Select DMX address
->
or
Select DMX channel mode (CH-1: 6ch /
CH-2: 11ch)
->
-
Set program speed
->
-
Select built-in program
->
Select sound active mode
->
-
Select static colour mode
(See static colour mode chart below)
->
-
Set strobe speed (Hz)
->
-
Set red colour intensity
->
-
Set green colour intensity
->
-
Set blue colour intensity
->
-
Set white colour intensity
->
-
Set amber colour intensity
->
-
Set UV colour intensity
->
-
Set dimmer speed
(nod0: fastest / nod4: slowest)
->
or
Toggle LED display on / off
->
Long press “Enter” button to show current temperature
->
Show current software version
->
or
Restore settings to factory default

www.event-lighting.com.au
4
Static Colour Mode
Value
Function
C1
Red
C2
Green
C3
Red+Green
C4
Blue
C5
Blue+Red+UV
C6
Green+Blue
C7
Red +Green+Blue+Amber+UV
C8
White
C9
Red+White
C10
Green+White
C11
Red+Amber
C12
Blue+White+UV
C13
Red + Blue+White+UV
C14
Red + Blue+White
C15
Red+Green+Blue+White+Amber+UV
DMX Chart
6 Channel Mode
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
5
000-255
Amber: 0% ~ 100%
6
000-255
UV: 0% ~ 100%