Event Lighting PRO PAR PAR6X12OB User manual

PAR6X12OB
6x 12W RGBWAU Outdoor Battery LED PAR
USER MANUAL
For your safety, please read this user manual carefully before use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version 1.0
Safety Instructions

www.event-lighting.com.au
1
Warning
•Do not open this device, there are no user serviceable parts inside. Risk of electric
shock.
•Do not look directly at the light source from close range.
•Avoid contact with the unit during operation, as the housing may become hot. Allow the
fixture to cool for at least 15 minutes after turning off before touching.
•Install this device in a location with adequate ventilation, at least 50cm from adjacent
surfaces.
•Do not operate this device, or connect this device to power, within 50cm of any
flammable material.
•Use a safety chain when mounting this device overhead.
•Do not operate this device outdoors where excessive dust, heat, water, or humidity may
affect it.
•This device is IP65 certified, meaning that it is protected against dust ingress, and
protected against low pressure water jets from any direction. Ensure all protective covers
are sealed correctly.
•Do not operate this device if the housing, lenses, or cables appear damaged.
•Do not connect this device to a dimmer or rheostat.
•Do not operate this device at temperatures higher than 40°C (104°F).
•Only connect this device to a grounded and protected circuit.
•Only use the hanging bracket to carry this device.
•Stop using this device immediately if a serious operating problem becomes apparent.
Product Installation
PAR6X12OB can be mounted in many orientations, provided each individual device is secured
by the use of the correct mounting bracket. Use a safety chain when mounting PAR9X15O
overhead.

www.event-lighting.com.au
2
Dimensions
Lux Chart
Distance (m)
1
2
3
4
5
Diameter (m)
Ø0.73
Ø1.46
Ø2.18
Ø2.91
Ø3.64
R
310
75
35
20
13
G
1,160
340
150
80
56
B
1,205
320
136
76
2
W
1,280
330
149
80
49
A
438
110
49
28
18
U
238
62
26
15
10
Full
3,820
970
460
290
180

www.event-lighting.com.au
3
Control Board Operation
->
-
Select DMX address for 6 ch mode
->
-
Select DMX address for 10 ch mode
->
or
Set dimming speed (SL: slow / FA: fast)
->
or
When lost DMX signal,
ho: keep the last DMX signal state
OF: blackout
->
or
Switch on/off wireless DMX control
->
or
Switch on/off IR remote control
->
-
Set red colour intensity
->
-
Set green colour intensity
->
-
Set blue colour intensity
->
-
Set white colour intensity
->
-
Set amber colour intensity
->
-
Set UV colour intensity
->
-
Display IR control brightness level
->
-
Set strobe speed
->
-
Select 15 static colour modes, see chart:
Static colour mode
->
-
Select 16 speed of auto colour switch mode
->
-
Select 16 speed of auto colour fading mode
->
-
Select 16 speed of auto colour pulse out
mode
->
-
Select sound active mode with different
sound sensitive level
Display current temperature
Display version number
->
or
Reset

www.event-lighting.com.au
4
Static Colour Mode
Value
Function
C1
R
C2
G
C3
R + G
C4
B
C5
B + R + UV
C6
G + B
C7
R + G + B + A + UV
C8
W
C9
R + W
C10
G + W
C11
R + A
C12
B + W + UV
C13
R + B + W + UV
C14
G + B + W
C15
R + G + B + W + A + UV
Wireless DMX Mode
Set Up Wireless DMX
PAR6X12OB needs to be paired from the Wireless DMX transmitter. Follow the steps below to
pair:
1. Connect the DMX512 controller to the wireless DMX transmitter.
2. Switch on PAR6X12OB, turn on the wireless DMX control on from control panel ‘rfon’
3. Set the PAR6X12OB to DMX mode. (AXXX or dXXX)
4. Switch off PAR6X12OB. Then, press and hold the ‘DMX select’ button whilst switching on
PAR6X12OB. Once PAR6X12OB turns on, the ‘wireless status’ light will be lit white and
the unit will be in ‘setup mode’.
5. The ‘wireless indicator’ will be lit to a specific colour to indicate the protocol being used
for the transmission as shown in TABLE1. Pressing the button will cycle through the
colours.
6. Once the desired protocol is selected, press the button for more than 1 second to save
the protocol. The transmitters, receivers and transceivers will remember the protocol
used even after a power cycle with their built-in memory chip.
Now, select either WDMX Mode or ELDMX Mode.
Table 1 Protocols
Colour
Protocol
Red
ELDMX Transmit and Receive
Green
WDMX Receive
Blue
WDMX G3 Transmit
Purple
WDMX G4 Transmit
Yellow
GZ Receive (Receiver Only)

www.event-lighting.com.au
5
Using WDMX Mode
Transmitters
Press the button to connect all unconnected receivers in the coverage area.
Press the button for 3 seconds to disconnect all receivers in the coverage area.
Receivers
Press the button for 3 seconds to disconnect the device from the transmitter it is currently
connected to.
Note: The colour of the light will indicate the group. Refer to Table 2 below.
Note: The receiver will not connect with a new transmitter unless it is disconnected first.
Table 2 WDMX Status Indicators
Protocol
Action
Description
W-DMX Receive
White
No connection
Red
Deleting Connection
Red Fast Flash
Connection Lost
Green Fast Flash
Connecting to Transmitter
Green Slow Flash
Connected but no DMX signal
Green
Connected with DMX signal
W-DMX Transmit
Red
Deleting All Receivers
Blue Fast Flash
Connecting with the receivers
Blue Slow Flash
No DMX input
Blue
Transmitting DMX
Using EL/GZ Wireless DMX Mode
Changing Channel Group
Press the button to display the current channel group being used.
Press the button again to cycle through the groups. The colour of the light will indicate the group
as shown in Table3.
Table 3 Status Indicators
Protocol
Action
Description
ELDMX / GZ
Solid Colour (Red, Green,
Blue, Yellow, Cyan, Purple,
White*)
1 of the 7* colour groups
(*7th white only in GZ mode, 6 in ELDMX mode)
Flashing Red
Transmitting DMX
Flashing Green
Receiving DMX

www.event-lighting.com.au
6
IR Remote Control Mode
•You must switch off wireless DMX function, select .
•Select , then use IR remote to switch on IR remote control mode.
Key
Function
Display
Switch on/off IR function
to
or your last setting
Press <blackout> button to switch
on the fixture IR function, fixture
will go to CC12 auto colour switch
mode or your last setting
Press <blackout> button when unit
under IR mode, fixture will blackout
and be on IR standby mode
Select auto colour switch
mode (CC) or auto colour
pulse out mode (CP) with
different speed
Between
Use <Auto> button to select CC or
CP mode, using to change
speed.
Select sound active mode
(SU) with different sensitivity
level
Press <SOUND> button to select
SU mode, use to change
sensitivity level
Select auto colour fade
mode (dE) with different
speed
Press <FADE> button to select dE
mode, use to change
speed.
Select manual colour mode
to
Press <MANUAL> button to enter
manual colour mode
Use
button to cycle though 20% change
of intensity of each colour
separately.
to
Press <MANUAL> button to quit
manual colour mode, fixture will
blackout
Select intensity of LED full
on mode
to
Press <%> button to cycle though
10% change of intensity on static
colour
(R255+G255+B255+W255+A255+
U255) mode.
Select intensity of static
colour
(R255+G255+B255+W255+
A255+U255)
to
Use to change intensity
Select intensity of static
colour (R255)
to
Use to change intensity
Select intensity of static
colour (UV50+R255)
to
Use to change intensity

www.event-lighting.com.au
7
Select intensity of static
colour (R255+G50)
to
Use to change intensity
Select intensity of static
colour (G255)
to
Use to change intensity
Select intensity of static
colour (G160+B255+UV100)
to
Use to change intensity
Select intensity of static
colour (B255+UV50)
to
Use to change intensity
Select intensity of static
colour (R50+B255+UV200)
to
Use to change intensity
Select intensity of static
colour (R255+B150+UV255)
to
Use to change intensity
Select intensity of static
colour (R255+B20+A200)
to
Use to change intensity
Reset factory default setting
to
No function
Add strobe effect on CC, CP,
SU, dE, dl and static colour
mode.
No change
Press <STROBE> button to cycle
though 1/8 change of strobe speed
DMX Chart
6 Channel Mode
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
5
000-255
Amber: 0% ~ 100%
6
000-255
UV: 0% ~ 100%
10 Channel Mode

www.event-lighting.com.au
8
Channel
Value
Function
1
000-255
Red: 0% ~ 100%
2
000-255
Green: 0% ~ 100%
3
000-255
Blue: 0% ~ 100%
4
000-255
White: 0% ~ 100%
5
000-255
Amber: 0% ~ 100%
6
000-255
UV: 0% ~ 100%
7
000-255
Master Dimmer 0% ~ 100%
8
000-255
Strobe (slow-fast)
9
000-050
No function
051-100
Select 15 Static colour mode (CL), colour have been controlled
by ch10
101-150
Select Auto colour switching modes (CC), program speed have
been controlled by ch10
151-200
Select Auto colour fade mode (dE), program speed have been
controlled by ch10
201-250
Select Auto colour pulse mode (CP), program speed have
been controlled by ch10
251-255
Select Sound active mode (SU), sound sensitivity level have
been controlled by ch10
10
(Ch9 set 051-
100)
000-015
No function
016-031
R
032-047
G
048-063
R + G
064-079
B
080-095
B + R + UV
096-111
G + B
112-127
R + G + B + A + UV
128-143
W
144-159
R + W
160-175
G + W
176-191
R + A
192-207
B + W + UV
208-223
R + B + W + UV
224-239
G + B + W
240-255
R + G + B + W + A + UV
10
(Ch9 set 101-
250)
000-255
Select auto run speed for (CC, dE and CP) from slow to fast
10
(Ch9 set 251-
255)
000-255
Select sound sensitivity level for sound active mode (SU) form
low to high

www.event-lighting.com.au
9
Technical Specifications
Power
•Input Voltage: 100~240V AC, 50/60 Hz
•Power Consumption: 72W
•Connection: Seetronic® Outdoor Powercon input connection
Photometrics
•Light Source: 6pcs 6-in-1 RGBWAU 12W LED
•Beam Angle: 40°
•PWM: 20,000 Hz
•LED Lifespan: 50,000 hours
Effects
•Dimming: 0~100%
•Strobe: 0~20 Hz
Control
•Protocol: DMX512, Wireless DMX
•DMX Channels: 6 / 10
•Built-in Programming: Yes
•Display: 4-button & 4-digit LED display control panel
•Cooling: Fanless
Battery
•Approx. 4 hours full colour
•Approx. 20 hours single colour at auto run
Housing
•Materials: Die-cast Aluminium
•Finishing: Matte black
•IP rating: IP65
•Net Weight: 3 kg
•Overall Size: 240 x 165 x 210 mm
Warranty
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.