Event Lighting M1H200W User manual

M1H200W
Hybrid Moving Head with CMY, CTO and Zoom
USER MANUAL
For safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to
change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting
for any clarification or information regarding this item.
www.event-lighting.com.au
V1.0

2
www.event-lighting.com.au
Safety Instructions
WARNING
• Do not open this device, there is no user-serviceable parts inside. Risk of electric shock.
• Do not look at the light source when the device is on.
•CAUTION: This unit's housing may be hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inch (50 cm) from adjacent surfaces.
• Do not leave any flammable material within 50 cm of this unit while operating or connected to power.
• Use a safety chain when mounting this device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water, or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• ONLY connect this device to a grounded and protected circuit.
• ONLY use the hanging bracket to carry this device.
• In case of a serious operating problem, stop using immediately.
• The maximum ambient temperature is 104° F (40° C). Do not operate this device at higher temperatures.
Power Input & Power Linking
This device has an auto-switching power supply work with input voltage range of 100~240 VAC, 50/60 Hz.
Link up to the maximum 8A. DO NOT exceed this.
Fuse Replacement
If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Before replacing the fuse, unplug mains lead.
Procedure:
Step 1: Unscrew the fuse holder on the rear panel with a fitting screwdriver from the housing (anticlockwise).
Step 2: Remove the old fuse from the fuse holder.
Step 3: Install the new fuse in the fuse holder.
Step 4: Replace the fuse holder in the housing and fix it.
Product Installation
This device can be mounted in many orientations provided each
individual device is secured by the use of correct mounting bracket.
Use a safety chain when mounting this device overhead.

3
www.event-lighting.com.au
Product appearance, LUX chart, Dimensions
1. Project lens
2. Head
3. Arm
4. Base
5. Display
6. Foot stand
7. Operation button
8. Handle
9. Wireless indicator
10. Mic
11. Left button
12. Battery indicator
13. Up button
14. Down button
15. Enter button
16. Right button
17. 3-pin DMX in
18. 5-pin DMX in
19. 3-pin DMX out
20. 5-pin DMX out
21. Powercon in
22. Powercon out
23. Fuse
24. Power switch

4
www.event-lighting.com.au
Lux Chart

5
www.event-lighting.com.au
Colour wheel
1
Open
2
Magenta
3
Orange
4
Sky blue
5
Pink
6
Yellow
7
Green
8
Blue
9
Red

6
www.event-lighting.com.au
Rotating gobo wheel
Position 1
Position 2
Position 3
Position 4
Position 5
Position 6
Position 7
Position 8

7
www.event-lighting.com.au
Static gobo wheel
Position 1
Position 2
Position 3
Position 4
Position 5
Position 6
Position 7
Position 8

8
www.event-lighting.com.au
Menu operation
Description of icons in the menu
CONNECT
LIGHT
INFOMATION
SET
PROGRAM
Menu
Default setting shadowed. Mark with ①can be basic reloaded, ②be program reloaded, ③can be private reloaded.
Con
nect
DMX Address①
XXX
DMX address setting
Wireless①
Wireless Enabled
Light
Turn On / Off
ON/OFF
Turn On the lamp
Automatic
ON/OFF
Lamp On/Off when power on
DMX Control
ON/OFF
DMX Control or not
Max Temperature
①
80~139℃90℃/176~282℉194℉
Lamp off if temperature
continuously over for 5 minutes
Lamp Adjust①
PAN……
Adjust value of channel
Information
Time Info.
Current XXXX(Hours)
Fixture Life XXXX(Hours)
Lamp Life XXXX(Hours)
Fixture boot time
Fixture total run time
Lamp total run time
Temperature
Near Lamp Temp (depends on fixture)
Temperature Sensors
Fans Speed
Near Lamp Fan (depends on fixture)
Fan speed Sensors
Channel Value
PAN……
Display value of channel
Error Message
Pan,Tilt……
Error channels
Fixture Model
xxxxxxxxxxxx
Display model brand and model
Software Ver
1U01 V1.0.00………
Version of each IC
Set
Reset
All
Pan&Tilt
Colors
Gobos
Others
Reset all
Reset Pan&Tilt
Reset Colors
Reset Gobos
Reset Others
Movment
Pan Reverse①
Tilt Reverse①
Pan Degree①
Encoders①
Pan/Tilt Mode①
ON/OFF
ON/OFF
630/540
ON/OFF
Stand/Smooth
Pan Reverse
Tilt Reverse
Choose Pan Degree
Encoder wheel on/off
Choose pan/tilt mode
UI Set
Mic Sens. ③
No Signal①
Temperature. C/F①
Fans Mode①
Hibernation①
Backlight①
Flip Display①
Display Bright③
0~99%,60%
Close/Hold/Auto/Music
Fahrenheit /Celsius
Auto Speed /High Speed
OFF, 01M~99M，15M
02~60m 02m
ON/OFF
00~31 10
Sensitivity of Mic
Mode when no signal
Temperature at ℃/℉
Fans mode
Sleeping mode
Show backlight time
Display 180°reverse
Display Brightness

9
www.event-lighting.com.au
Brand Show①
Key Lock①
Language③
ON/OFF
ON/OFF
En/简/繁/Fr/Sp
Show brand or not
Key lock on/off
Language Select
Users
User Mode①
Standard
Extended
Basic-8bit
Basic-16bit
User
Standard mode
Extended mode
Basic-8bit mode
Basic-16bit mode
User program mode
Edit User③
Max Channel = XX
PAN = CH01
:
Edit users mode
Calibration③
-Password-
Color
:
=XXX
=XXX
:
Password: 050
Calibrate channel value
Fixture ID③
Name
-Password-
PID Code
Name
Password: 050
Set PID of RDM
Wireless Set①
DMX On Cable
Reset Connect
ON/OFF
ON/OFF
DMX Send Out
Reset Connect
Reload Default
Basic Reload(①)
Program Reload(②)
---Password---
Private Reload(③)
All Reload
ON/OFF
ON/OFF
XXX
ON/OFF
ON/OFF
Basic Reload
Program Reload
Password: 050
Private Reload
All Reload
Program
Play①
DMX Receive
Slave Receive
Sequence
Music
Slave Receive 1,2,3
Master / Alone
Master / Alone
DMX Receive
Choose slave position
Run Sequence
Music mode
Select Chase②
Chase Part 1
Chase Part 2
Chase Part 3
Chase 1 ~ 8 Chase 1
Chase 1 ~ 8 Chase 2
Chase 1 ~ 8 Chase 3
Select and run auto program
Edit Chase②
Chase 1
:
Chase 8
Chase Test
Step 01
Step 64
=SCxxx
=SCxxx
Test
Beginning scene
Ending scene
Edit Scenes②
Edit Scene 001
~ Edit Scene 250
Pan,Tilt,……
--Fade Time--
--Secne Time--
DMX Input
=xxx
=xxx
=xxx
Input manual scene
Modify manually fading time
Modify manually scene time
Input scene from exterior
controller
Scenes Record
ScXX=>ScXX
Auto Input scenes

10
www.event-lighting.com.au
DMX Chart
Channel
name
function
Min DMX
Max DMX
St
Ex
Ba1
Ba2
1
1
1
1
Pan
Pan Coarse
0
255
2
2
2
Pan fine
Pan Fine
0
255
3
3
2
3
Tilt
Tilt Coarse
0
255
4
4
4
Tilt fine
Tilt Fine
0
255
5
5
3
5
Movment
Speed
fastest to Slowest
0
255
6
Movment
Function
Normal
0
15
Movement With Backout
16
31
TBD
32
255
6
7
Shutter
Function
Normal Shutter Functions
0
15
Pulse-effect Forward
16
31
Pulse-effect Reverse
32
47
Random Strobe
48
63
TBD
64
255
7
8
Shutter
Normal Shutter Functions
Close
0
31
Strobe Rate (slow to fast)
32
223
Open
224
255
Pulse-effect Forward
Close
0
31
Strobe Rate (slow to fast)
32
223
Open
224
255
Pulse-effect Reverse
Close
0
31
Strobe Rate (slow to fast)
32
223
Open
224
255
Random Strobe
Close
0
31
Strobe Rate (slow to fast)
32
223
Open
224
255
4
6
Shutter
Shutter closed
0
31
No function (shutter open)
32
63
Strobe effect slow to fast
64
95
No function (shutter open)
96
127
Pulse-effect in sequences
128
159
No function (shutter open)
160
191

11
www.event-lighting.com.au
Random strobe effect slow to fast
192
223
No function (shutter open)
224
255
8
9
5
7
Dimmer
Dimmer(Close to Open)
0
255
9
10
Color
Function
Indexed
0
15
Indexed With BackOut
16
31
Forward Spin
32
47
Reverse Spin
48
63
Continuous
64
79
Color Bounce
80
111
TBD
112
255
10
11
Color
Indexed & Indexed With
BackOut&Color Bounce
Position 1 (Open)
0
13
Position 2
14
27
Position 3
28
41
Position 4
42
55
Position 5
56
69
Position 6
70
83
Position 7
84
97
Position 8
98
111
Position 9
112
125
Position 10
126
139
Position 11
140
153
Position 12
154
167
Position 13
168
181
Position 14
182
195
Position 15
196
209
Position 16
210
223
Position 17
224
237
Position 18
238
255
Forward Spin
Stop to fastest
0
255
Reverse Spin
Stop to fastest
0
255
Continuous
Positioning from 0-360 degrees
0
255
6
8
Color
Indexed
Position 1 (Open)
0
2
Position 2
3
5
Position 3
6
8
Position 4
9
11
Position 5
12
14

12
www.event-lighting.com.au
Position 6
15
17
Position 7
18
20
Position 8
21
23
Position 9
24
26
Position 10
27
29
Position 11
30
32
Position 12
33
35
Position 13
36
38
Position 14
39
41
Position 15
42
44
Position 16
45
47
Position 17
48
50
Position 18
51
53
Indexed With Backout
Position 1 (Open)
54
56
Position 2
57
59
Position 3
60
62
Position 4
63
65
Position 5
66
68
Position 6
69
71
Position 7
72
74
Position 8
75
77
Position 9
78
80
Position 10
81
83
Position 11
84
86
Position 12
87
89
Position 13
90
92
Position 14
93
95
Position 15
96
98
Position 16
99
101
Position 17
102
104
Position 18
105
106
Indexed With Bounce
Position 1 (Open)
107
119
Position 2 Red
120
132
Position 3 Blue
133
145
Position 4 Green
146
158
Position 5 Yellow
159
171
Position 6 Pink
172
184
Position 7 Sky blue
185
197
Position 8 Orange
198
210
Position 9 Megenta
211
223

13
www.event-lighting.com.au
Forward Wheel Spin
Stop to fastest
224
239
Reverse Wheel Spin
Stop to fastest
240
255
11
12
Rot Gobo
Function
Indexed
0
15
Indexed With BackOut
16
31
Forward Spin
32
47
Reverse Spin
48
63
Continuous
64
79
Shake
80
95
TBD
96
255
12
13
Rot Gobo
Indexed & Indexed With
Backout&Shake
Position 1 (Open)
0
31
Position 2
32
63
Position 3
64
95
Position 4
96
127
Position 5
128
159
Position 6
160
191
Position 7
192
223
Position 8
224
255
Forward Wheel Spin
Stop to fastest
0
255
Reverse Wheel Spin
Stop to fastest
0
255
Continuous
Positioning from 0-360 degrees
0
255
7
9
Rot Gobo
Indexed
Position 1 (Open)
0
5
Position 2
6
11
Position 3
12
17
Position 4
18
23
Position 5
24
29
Position 6
30
35
Position 7
36
41
Position 8
42
47
Indexed With Backout
Position 1 (Open)
48
53
Position 2
54
59
Position 3
60
65
Position 4
66
71
Position 5
72
77

14
www.event-lighting.com.au
Position 6
78
83
Position 7
84
89
Position 8
90
97
Indexed With Shake
Position 2
98
115
Position 3
116
133
Position 4
134
151
Position 5
152
169
Position 6
170
187
Position 7
188
205
Position 8
206
223
Forward Wheel Spin
Stop to fastest
224
239
Reverse Wheel Spin
Stop to fastest
240
255
13
14
Gobo Rot
Function
Continuous
0
15
Forward Spin
16
31
Reverse Spin
32
47
Forward Animate Rotate
48
63
Forward Animate Rotate With Backout
64
79
Reverse Animate Rotate
80
95
Reverse Animate Rotate With Backout
96
111
TBD
112
255
14
15
Gobo Rot
Continuous
Positioning from 0-360 degrees
0
255
Forward Spin
Stop to fastest
0
255
Reverse Spin
Stop to fastest
0
255
Forward Animate Rotate & Forward
Animate Rotate With Backout
Stop to fastest
0
255
Reverse Animate Rotate & Reverse
Animate Rotate With Backout
Stop to fastest
0
255
8
10
Gobo Rot
Continuous
Positioning from 0-360 degrees
0
191
Forward Animate Rotate
Stop to fastest
192
207
Reverse Animate Rotate
Stop to fastest
208
223
Forward Spin

15
www.event-lighting.com.au
Stop to fastest
224
239
Reverse Spin
Stop to fastest
240
255
15
16
Gobo
Function
Indexed
0
15
Indexed With BackOut
16
31
Forward Spin
32
47
Reverse Spin
48
63
Continuous
64
79
Shake
80
95
TBD
96
255
16
17
Fixed Gobo
Indexed & Indexed With
Backout&Shake
Position 1 (Open)
0
31
Position 2
32
63
Position 3
64
95
Position 4
96
127
Position 5
128
159
Position 6
160
191
Position 7
192
223
Position 8
224
255
Forward Wheel Spin
Stop to fastest
0
255
Reverse Wheel Spin
Stop to fastest
0
255
Continuous
Positioning from 0-360 degrees
0
255
9
11
Fixed Gobo
Indexed
Position 1 (Open)
0
5
Position 2
6
11
Position 3
12
17
Position 4
18
23
Position 5
24
29
Position 6
30
35
Position 7
36
41
Position 8
42
47
Indexed With Backout
Position 1 (Open)
48
53
Position 2
54
59
Position 3
60
65
Position 4
66
71
Position 5
72
77
Position 6
78
83

16
www.event-lighting.com.au
Position 7
84
89
Position 8
90
95
Indexed With Shake
Position 2
98
115
Position 3
116
133
Position 4
134
151
Position 5
152
169
Position 6
170
187
Position 7
188
205
Position 8
206
223
Forward Wheel Spin
Stop to fastest
224
239
Reverse Wheel Spin
Stop to fastest
240
255
17
18
10
12
Prism
Indexed & Indexed With Backout
Position 1 (Open)
0
3
Forward Spin
Stop to fastest
0
127
Reverse Spin
Stop to fastest
128
255
18
19
11
13
Frost
Frost 0-100%
0
255
19
20
Focus
Function
Continuous
0
15
5m Auto Focus
16
31
7.5m Auto Focus
32
47
10m Auto Focus
48
63
15m Auto Focus
64
79
>20m Auto Focus
80
95
TBD
96
255
20
21
12
14
Focus
Continuous
Focus In to Focus Out
0
255
Auto Focus
Focus In to Focus Out Fine
0
255
21
22
13
15
Zoom
Continuous
Zoom Small to Big
0
255
22
23
Iris Function
Indexed
0
15
Pulse opening With Forward Backout
16
31
Pulse opening With Reverse Backout
32
47
Pulse closing With Forward Backout
48
63
Pulse closing With Reverse Backout
64
79
TBD
80
255
23
24
Iris
Indexed
Max. diameter to Min.diameter
0
255

17
www.event-lighting.com.au
Pulse opening & Pulse closing
Pulse Slow to Fast
0
255
14
16
Iris
Indexed
0
191
Pulse opening With Forward Backout
192
207
Pulse opening With Reverse Backout
208
223
Pulse closing With Forward Backout
224
239
Pulse closing With Reverse Backout
240
255
24
25
15
17
Control
Normal
0
7
Reset All
8
15
Pan&Tilt Reset
16
23
Color Reset
24
31
Gobo Reset
32
39
TBD
40
47
Other Reset
48
55
Display Off
56
63
Display On
64
71
TBD
72
79
TBD
80
87
Hibernation
88
95
TBD
96
255
The device is controlled by universal DMX 512 protocol, DMX address is the start channel used to receive instructions
from the external controller. For independent control, each fixture must be assigned its unique address control channels.
For example, this device has four channel modes: 24/25/15/17, if we set the mode at standard 24 channels mode, and
there are several models need to be independently controlled, we just simply address first fixture at 1, and second
fixture at 25, third one at 49, etc.
- If the devices have the same address, they will behave synchronically.
- Display is flashing when no DMX signal is received.
More functions
- RDM. RDM stands for “Remote Device Management”, with this function, users can realize remote control of the
device, such as remotely changing DMX address, reverse pan/tilt setting, check a lot of useful information such as
temperature, power consumption, fan speed. Etc. Every single device has a unique RDM code programmed at
manufacture to distinguish from each other. It is not recommended for users to change this code.
- Software upgrade function via DMX cable. If there is any new firmware for this device, it can be upgraded simply via
a software upgrade box, no need to change any mechanical parts. The upgrade box is not included in the package,
if need any further assistance please just contact your authorized dealer.
- Hibernation. The device will enter sleeping mode if activated after a period of disconnecting DMX signal to save the
power consumption, and will return immediately as soon as the DMX signal is sent again.
- Display back-up communication IC. There is a back-up communication IC installed in the display PCB, so users
could replace at once if the original one is broken.
- Display flip. By press up and down button for more than 3 seconds, the display will flip automatically, this function is
useful to read menu conveniently when device is hanged.

18
www.event-lighting.com.au
Technical Specifications
Power
− Input Voltage: 100~240V AC, 50/60 Hz 275W
− Connection: Neutrik® PowerCON - In / Out
Photometrics
− Light Source: Advanced 6500K 200W White LED Module
− Beam Angle: 7.5° to 40°
− Output: 16,100 lumen, 61,100 lux on @2.5M @7.5°
− PWM: 1200Hz
− LED Lifespan: 60,000 hours
Effects
− Dimming: 0 ~ 100%
− Strobe: 0.5 ~26 Hz
− Focus: Electronic Linear
− Prism: 3-facet & Frost
− Iris: Yes
− Zoom: Electronic Linear 7.5° to 40°
Movement 16 bit Auto Reposition
− Pan: 630°( 4.3 sec) or 540°( 3.9 sec)
− Tilt: 233°(2.2 sec)
Colour 8 Colours + Open
Gobos
− Fixed: 1 x 7 + Open Fixed Gobo Wheel
− Rotating: 1 x 7 + Open Interchangeable Rotating Gobo Wheel (Outside Ø27mm, Inside Ø20mm).
Control
− Operational Modes: DMX, Auto Program, Sound Active, Master / Slave
− RDM: Change DMX Address, Display Flip, X/Y Reverse and so on
− Protocol: DMX512 (W-DMX™ Optional)
− DMX Channels: 24 / 25 / 15 / 17
− Interface: 3-Pin & 5-Pin XLR
− Display: 2.4″ Colour LCD Control Panel with Back-up Power.
− Software Upgrade via DMX: Yes
Housing
− Materials: ABS & Steel
− Finishing: Matte black
− Cooling: Multi Sensor Thermostat Controlled Variable Speed Fan
− IP rating: IP20
− Net Weight: 25 kg
− Rigging: 2pcs Omega Brackets with 1/4-turn Quick Locks
MISC Road case: MCASE1LS MCASE2VLS
WARRANTY
Please refer to your local dealer or please contact Event Lighting Pty Ltd
Website: www.event-lighting.com.au.