Event Lighting ZP200LE User manual

ZP200LE
200 W LED Fresnel/Profile Spot - Light Engine
USER MANUAL
For your safety, please read this user manual carefully before initial use.
Event Lighting reserves the right to revise the manual at any time. Information and specifications
within this manual are subject to change without notice. Event Lighting assumes no liability or
responsibility for any errors or omissions. Please consult Event Lighting for any clarification or
information regarding this item.
Version: S109.1

www.event-lighting.com.au
2
Safety Instructions
Warning
• Do not open this device, there are no user serviceable parts inside. Risk of electric
shock.
• Do not look at the light source when the device is on.
• CAUTION: This unit’s housing may become hot during and after operation.
• Install this device in a location with adequate ventilation, at least 20 inches (50 cm) from
adjacent surfaces.
• Do not leave any flammable material within 20 inches (50 cm) of this unit while operating
or connected to power.
• Use a safety chain when mounting the device overhead.
• Do not operate this device outdoors or in any location where dust, excessive heat, water
or humidity may affect it.
• Do not operate this device if the housing, lenses, or cables appear damaged.
• Do not connect this device to a dimmer or rheostat.
• Only connect this device to a grounded and protected circuit.
• Only use the hanging bracket to carry this device.
• If there is any concern of a serious problem, stop using this device immediately.
• Do not operate this device at ambient temperatures higher than 40° C (104° F).
Power Input and Power Linking
This device has an auto-switching power supply that works with 100-240 V AC, 50/60 Hz input.
Link up to the maximum of 8A. DO NOT exceed this.
Fuse Replacement
If the fine wire fuse of the device fuses, replace it with one of the same type and rating. Before
replacing the fuse, disconnect from mains power.
Procedure:
1. Unscrew the fuse holder on the rear panel from the housing with a fitting screwdriver.
2. Remove the old fuse from the fuse holder.
3. Install the new fuse in the fuse holder
4. Replace the fuse holder in the housing and secure it.
Product Installation
This device can be mounted in many orientations provided each individual device is secured by
the use of the correct mounting bracket. Use a safety wire/chain when mounting this device
overhead.

www.event-lighting.com.au
3
Dimensions
Lux Chart

www.event-lighting.com.au
4
Control Board Operation
1 – Menu: Move up one level.
2 – Up: Move up one item.
3 – Down: Move down one item.
4 – Enter: Move down one level/confirm selection.
Menu
Level 1
Level 2
Value
Information
DMX
DMX address
1-512
Set DMX address
CHAN
CH01
Use 1 channel mode
CH02
Use 2 channel mode
CH03
Use 3 channel mode
DIMMER
DIM
0-255
Manual control of Dimmer
D_F
0-255
Manual control of Dimmer-Fine
STO
0-255
Manual control of Strobe
HALOGEN
ON/OFF
CURVE
Linear
Linear dimming curve
Log
Logarithmic dimming curve
S
S dimming curve
FAN
Max
Fastest fan speed
Auto
Variable fan speed, based on thermal sensor
Silent
Theatre mode
TEMP
C.000
Current fixture temperature
RESET
YES/NO
Reset to factory default
VERSION
S109.01
Software version
Use Up and Down to select the desired item and Enter to confirm.
• When there is no DMX signal, a flashing “!” will be displayed on the screen.
• The screen will turn off if no buttons are pressed for 30 seconds.
Set DMX Address
Select “DMX” then press Enter.
Use Up and Down to set the desired DMX address from 1 to 512.
Press Enter to confirm and save.
Set DMX Channel Mode
Select “Chan” then press Enter.
Use Up and Down to set the desired DMX channel mode.
Press Enter to confirm and save.

www.event-lighting.com.au
5
Refer to the DMX Chart below for more information on each mode.
Set Manual Control
Manual Control allows you to set Dimmer, Dimmer Fine and Strobe values through the control
panel.
Select “Dimmer” then press Enter.
Select “DIM” for Dimmer, “D_F” for Dimmer Fine, or “STO” for Strobe, then press Enter.
Use Up and Down to set the desired value.
Press Enter to confirm and save.
Set Dimmer Curve
Select “Curve” then press Enter.
Use Up and Down to set the desired dimmer curve.
Press Enter to confirm and save.
Set Fan Mode
Select “Fan” then press Enter.
Use Up and Down to set the desired fan curve.
Press Enter to confirm and save.
DMX Chart
• This fixture is controlled by the universal DMX 512 protocol. The DMX address is the first
channel used to receive instructions from the external controller. For independent control,
each fixture must be assigned a unique address for each of its control channels. For
example, this device has three channel modes: 1/2/3, if it’s set to 3 channel mode, and
there are several fixtures need to be independently controlled, we just simply address
first fixture at 1, and second fixture at 4, third one at 7, etc.
• If multiple fixtures have the same DMX address, they will behave synchronically.
• Display will flash when no DMX signal is received.
Mode/Channel
Min.
DMX
Max.
DMX
Function
1 Ch
2 Ch
3 Ch
1
1
1
0
255
Dimmer
2
2
0
255
Dimmer-Fine
3
0
255
Strobe, slow to fast

www.event-lighting.com.au
6
Technical Specifications
Photometrics
• Light Source: 3200 K 200 W COB LED
• CRI: 95
• PWM: 16,000 Hz
• LED Lifespan: 50,000 hours
• PROFILE Lens: ZPLP1828 (order separately)
o Output: 1896 lux @ 5 m at 18°, 1692 lux @ 5 m at 28°
o Beam Angle: 18°- 28°
• PROFILE Lens: ZPLP2636 (order separately)
o Output: 1896 lux @ 5 m at 26°, 1692 lux @ 5 m at 36°
o Beam Angle: 26°- 36°
• FRESNEL Lens: ZPLF 80mm Fresnel (order separately)
o Output: 2198 lux @ 2.5 m at 16°, 1685 lux @ 2.5 m at 25°
o Beam Angle: 16°- 25°
o Field Angle: 30°- 55°
• CYC Lens: ZPLCYC (order separately)
o Output: 210 lux @ 2.5 m at 120°
o Beam Angle: 120°
Effects
• Dimming: 0~100%, 8-bit / 16-bit
• Strobe: 1~25 Hz
• Zoom: Manual
Power
• Input Voltage: 100~240 V AC, 50/60 Hz, 200 W
• Power Connection: Fixed
Control
• Operational Modes: DMX, Manual & Master / Slave
• Display: 4-Button LCD control panel
• DMX Protocol: DMX512
• DMX Channel Mode: 1 / 2 / 3
• DMX Interface: 3-pin XLR
Housing
• Housing Materials: Aluminium, matte black finish
• Cooling: Sensor Thermostat Controlled Variable Speed Fan
• Net Weight:
o LED Engine 9 kg
o Profile Lens: 1.9 kg
o Fresnel Lens: 0.9 kg
o Cyc Lens: 0.4 kg
Warranty
Please refer to your local dealer or contact Event Lighting.