fantastic furniture Bridge Bedside 1 Drawer User manual

Bridge
Bedside 1 Drawer Oak

r

Hardware Pack
Top Panel (P1)
Bottom Panel (P2)
Right Panel (P3)
Left Panel (P4)
Back Panel (P5)
Shelf (P6)
Support Panel (P7)
Drawer Door (P8)
Drawer Back (P9)
Drawer Left Panel (P10)
Drawer Right Panel (P11)
Drawer Bottom (P12)
2 x Legs(P13)
1 x Left Runner
Track
(H9-1)
4 x Long Screws
(H10)
16 x Cam Bolts
(H1)
16 x Cam Nuts
(H2)
16 x Dowels
(H3)
12 x Washers
(H4)
12 x Bolts
(H5)
1 x Allen Key
(H7)
4 x Levelling Feet
(H8)
12 x Screws
(H6)
1 x Right Runner
Track
(H -2)9
1 x
Runner
(H -3)
Left
9
1 x Right
Runner
(H -4)9
Top Panel
(P1)
Bottom Panel
(P2)
Right Panel
(P3)
Left Panel
(P4)
Back Panel
(P5)
Shelf
(P6)
Support Panel
(P7)
Drawer Door
(P8)
Drawer Back
(P9)
Drawer Left Panel
(P10)
Drawer Right Panel
(P11)
Drawer Bottom
(P12)
Legs
(P13)
Legs
(P13)
2 x Washers
(H11)
1 x Wall Strap
(H12)
1 x Medium Screw
(H13)
4 x
(H14)
Wedges

H8
P2
P13
H7
H5
H4
H1
H3
12 x Washers
(H4)
12 x Bolts
(H5)
1 x Allen Key
(H7)
4 x Levelling Feet
(H8)
Attach the 2 x legs (P13) to the bottom panel (P2) using 12 x bolts (H5)
and 12 x washers (H4), completely tightening using the allen key (H7).
Screw in the 4 x levelling feet (H8) into the 2 x legs (P13) as shown.
Ensure they are secure.These can be adjusted after the bedside is assembled to
ensure the unit is level.
8 x Cam Bolts
(H1)
8 x Dowels
(H3)
Phillips Head
Screwdriver
Insert 4 x dowels (H3) into the bottom panel (P2). Secure 4 x cam bolts (H1)
into the bottom panel, tightening using a phillips head screwdriver.
Repeat this step for the top panel (P1).
P2
H1
H3 P1

4
4 x Cam Bolts
(H1)
8 x Dowels
(H3)
Phillips Head
Screwdriver
Insert 4 x dowels (H3) into right panel (P3) and secure 2 x cam bolts (H1) to
right panel (P3), tightening using a phillips head screwdriver.
Repeat this step for the left panel (P4).
P3
P4
Align and attach the shelf (P6) and support panel (P7) between the right and
left panel (P3, P4) as shown.
Carefully turn the unit upside down.
Insert 4 x cam nuts (H2) into the shelf (P6) as shown. Rotate the cam nuts so the
arrows point towards the incoming cam bolts.
Secure the panels together (P3, P4, P6, P7) by tightening the 4 x cam nuts (H2)
using a phillips head screwdriver.
P7
P6
P3
P4
4 x Cam Nuts
(H2) Phillips Head
Screwdriver
H2
H2
H2
H2

Page 7
5
6
Align and attach the assembled frame onto the bottom panel (H2) as shown,
ensuring the grooves on the right panel (P3), left panel (P4) and bottom panel (P2) align.
Insert 4 x cam nuts (H2) into the top of the right panel (P3) and left panel (P4), rotating the
cam nuts so the arrow points towards the incoming cam bolt.
Secure the frame to the bottom panel (P2) by tightening the cam nuts (H2)
using a phillips head screwdriver.
4 x Cam Nuts
(H2) Phillips Head
Screwdriver
H2
H2
H2
P3
P4
P2
P5
Slide back panel (P5) into the groove of right panel (P3), left panel (P4) and
bottom panel (P2) as shown.

Page 8
7
8
H5
Align and attach the top panel (P1) onto the assembled frame as shown.
Insert 4 x cam nuts (H2) into the top of the right panel (P3) and left panel (P4),
rotating the cam nuts so the arrow points towards the
incoming cam bolts.
Secure the top panel (P1) to the assembled frame by tightening the
cam nuts (H2) using a phillips head screwdriver.
4 x Cam Nuts
(H2) Phillips Head
Screwdriver
Secure 4 x cam bolts (H1) to drawer door (P8) , tightening using a
phillips head screwdriver
4 x Cam Bolts
(H1) Phillips Head
Screwdriver
(P8)
(H1)
(H1)
(H1)
(H1)

Page 9
9
10
Attach drawer left panel (P10) and drawer right panel (P11) to drawer door (P8),
ensuring the grooves on all the panels align as shown.
Slide the drawer bottom (P12) through the grooves on all drawer panels (P10, P11, P8)
as shown.
Insert 4 x cam nuts (H2) into the drawer left panel (P10) and drawer right panel (P11),
rotating the cam nut (H2) so the arrow points towards the incomcing cam bolt.
Secure the panels (P10, P11, P8) together by tightening the cam nuts (H2) using
a phillips head screwdriver.
4
(P10)
(P11)
(P12)
(P8)
Align drawer back to the assembled drawer as show. Ensure the pre-drilled holes on the
drawer left and right panels (P10, P11) align with the pre-drilled holes on the drawer back (P12).
Secure together using 4 x long screws (H10), tightening using a phillips head screwdriver.
(P9)
4 x Long Screws
(H10)
(H10)
(H10)
(H10)
(H10)
Phillips Head
Screwdriver

Page 10
11
12
4 x Screws
(H6)
Secure the left runner (H9-3) and right runner (H9-4) to the assembled drawer using
4 x short screws, tightening using a phillips head screwdriver.
Ensure the wheels on the runners are towards the back of the drawer as shown.
Phillips Head
Screwdriver
Left
Runner
(H9-3)
Right
Runner
(H9-4)
(H6)
(H9-4)
(H9-3)
(H6)
(H6)
(H6)
4 x Screw
(H6)
1 x Left Runner
Track
(H9-1)
1 x Right Runner
Track
(H9-2)
(P3)
Secure the right runner track (H9-2) to the right panel (P3) using 2 x screws (H6), tightening
using a phillips head screwdriver.
Ensure the wheels on the track are towards the front of the bedside as shown.
Repeat this step for the left runner track (H9-3)
(H6)
(H6)
(H6)
(H9-1)
Phillips Head
Screwdriver