fantastic furniture Eden User manual

Eden
Utility 4 Drawer Oak Glass
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend
that this product is permanently fixed to the wall or other suitable
surface. Connecting attachments for your wall are not included
since dierent surface materials require dierent attachments.
Please seek professional advice if you are in doubt of what wall
connections to use.
Recommended weight capacity : 15kg /Drawer & 10kg on top
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Page 2
Glass should always be handled with care.
cause glass to break. This glass is designed to break into small,
relatively harmless pieces and not sharp fragments. Avoid
placing hot or cold items directly onto the table unless using a
thick insulation material such as placemats or coasters.
Avoid dropping objects onto the glass.
Do not allow hard or pointed objects to come into contact
with the glass. Never use the top area as a chopping surface.
Do not sit or stand on the glass surface.

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1); Bottom Panel (P2);
Left Side Panel (P3); Right Side Panel (P4);
2 x Back Panels (P5); Rail (P6); Rail (P7);
Rail (P8); 2 x Rail (P9); Drawer Front (P10);
Left Drawer Side (P11);
Right Drawer Side (P12);
Drawer Back (P13); 4 x Rails (P14);
Drawer Base (P15); 3 x Drawer Front (P16);
3 x Left Drawer Side (P17);
3 x Right Drawer Side (P18);
3 x Drawer Back (P19);
3 x Drawer Base (P20);
4 x Dividers (P21);
2 x Dividers (P22)
Hardware pack
Top Panel
(P1)
Bottom Panel
(P2)
Left Side
Panel
(P3)
Right Side
Panel
(P4)
Back
Panel
(P5)
Back
Panel
(P5)
Rail
(P6)
Rail
(P7) Rail
(P8)
Rail
(P9) Rail
(P9)
2 x Divider
(P22)
4 x Divider
(P21)
Drawer
Front (P10)
Left Drawer
Side (P11)
Right Drawer
Side (P12)
Drawer
Back (P13)
Drawer
Base (P15)
Rail
(P14)
Drawer
Front (P16)
Left Drawer
Side (P17)
Right Drawer
Side (P18)
Drawer
Back (P19)
Drawer
Base (P20)
Rail
(P14)
x3
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
22 x Dowels
(H1)
24 x Long
Screws
(H2)
46 x Small
Screws
(H5)
2 x Slides
(H6)
34 x Cam
Bolts
(H3)
34 x Cam
Nuts
(H4)
4 x Support
Plug
(H15)
2 x Bolts
(H16)
2 x Allen
Keys
(H14)
2 x Nuts
(H17)
8 x Wedges
(H12)
4 x Plastic
Glides
(H11)
8 x Wedge
Screws
(H13)
1 x Safety
Strap
Screw
(H19)
1 x Safety
Strap
(H18)
2 x Washers
(H20)
3 x CL Runner
Tracks
(H7)
3 x CR Runner
Tracks
(H8)
3 x DL
Runners
(H9)
3 x DR
Runners
(H10)

(P3)
You will need
Step 1
Step 2
You will need
Attach 7 x Cam Bolts (H3) to Left Side Panel (P3) as shown by tightening with the Phillips
Head Screwdriver.
Separate 2 x Slide (H6) into Slide Tracks (H6-1) and Slide Runners (H6-2)
as shown below:
Press down on the plastic release lever to extend the
Slide Runner (H6-2) from Slide Track (H6-1) and then
separate the two pieces completely.
Adjust Runner to access the screw holes.
fantasticfurniture.com.au Page 5
7 x Cam Bolts
(H3)
Slide Runner
(H6-2)
Slide Track
(H6-1)
Slide Track
(H6-1)
2 x Slides
(H6)
Phillips Head
Screwdriver
H3
H3
H3
H3
H3
H6
H3
H3

12 x Small
Screws (H5)
(P3)
You will need
Step 3
Step 4
You will need
Secure 1 x Slide Track (H6-1) and 3 x CL Runner Tracks (H7) to Left Side Panel (P3) with 12 x
Small Screws (H5) by tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 6
H6-1
Phillips Head
Screwdriver
H5
H7
H7
H7
H7
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
H5
CL
3 x CL Runner
Tracks (H7)
Attach 7 x Cam Bolts (H3) to Right Side Panel (P4) as shown by tightening
with the Phillips Head Screwdriver.
Use the holes shown below on the
Slide Track (H6-1) to secure the screws.
1 x Slide Track
(H6-1)
H3
H3
H3
H3
H3
H3
H3
7 x Cam Bolts
(H3)
Phillips Head
Screwdriver

12 x Small
Screws (H5)
(P3)
(P8)
(P7)
(P6)
You will need
Step 5
Secure 1 x Slide Track (H6-1) and 3 x CR Runner Tracks (H8) to Right Side Panel (P4) with 12 x
Small Screws (H5) by tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 7
H1
H1
H1
H4
H4
H4
Step 6
You will need
Phillips Head
Screwdriver
3 x Cam Nuts
(H4)
3 x Dowels
(H1)
Insert 3 x Dowels (H1) into Left Side Panel (P3).
Insert 3 x Cam Nuts (H4) into Rails (P6, P7, P8).
Rotate the nuts so the arrows point towards
the incoming bolts. Attach Rails (P6, P7, P8) to Left
Side Panel (P3) by tightening all nuts with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
H8
H5
CR
(P4)
H3
H6-1
H8
H8
H8
H5
H5
H5
H5
H5
H5
H5
H5
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
1 x Slide Track
(H6-1)
Use the holes shown below on the
Slide Track (H6-1) to secure the screws.
3 x CR Runner
Tracks (H8)
H5 H5
H5

Step 8
You will need
(P3)
(P9)
(P9)
(P9)
(P9)
(P2)
(P2)
H1
H1
H1
H1
H1
H1
H1
H1
H4
H4
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
4 x Dowels
(H1)
Insert 4 x Dowels (H1) into Bottom Panel (P2) and attach Rails (P9 x 2) as shown.
Insert 4 x Dowels (H1) into Left Side Panel (P3).
Insert 4 x Cam Nuts (H4) into Bottom Panel (P2)
and Rails (P9 x 2). Rotate the nuts so the arrows
point towards the incoming bolts. Attach Bottom Panel (P2)
and Rails (P9 x 2) to Left Side Panel (P3) by tightening all nuts with
the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 8
Step 7
You will need
4 x Dowels
(H1)

You will need
Step 10
Insert 7 x Dowels (H1) into Bottom Panel (P2) and Rails (P6, P7, P8, P9 x 2) as shown.
Step 9
Slide Back Panels (P5 x 2) into the grooves of Bottom Panel (P2), Rails (P6 & P7)
and Left Side Panel (P3).
(P9)
(P9)
(P2)
(P8)
(P6)
(P7)
(P2)
(P3)
(P6)
(P5)
(P7) (P5)
fantasticfurniture.com.au Page 9
H1
H1
H1
H1 H1
H1
H1
7 x Dowels
(H1)
Ensure laminated
side of panel is
facing inwards.

You will need
Step 12
You will need
Phillips Head
Screwdriver
Step 11
Secure 4 x Plastic Glides (H11) to the
bottom of Left & Right Side Panels (P3 & P4)
as shown using the Hammer.
(P3)
(P9)
(P9) (P2)
(P4)
(P4)
(P8)
(P6)
(P7)
fantasticfurniture.com.au Page 10
H11
H11
H11
H11
H4
H4
H4
H4
H4
Insert 7 x Cam Nuts (H4) into
Bottom Panel (P2) and Rails
(P6, P7, P8, P9 x 2). Rotate the
nuts so the arrows point towards
the incoming bolts. Attach Right
Side Panel (P4) to Bottom Panel (P2)
and Rails (P6, P7, P8, P9 x 2) by
tightening all nuts with the Phillips Head Screwdriver.
7 x Cam Nuts
(H4)
Hammer
4 x Plastic
Glides (H11)