fantastic furniture HAVANA Lowline Large User manual

HAVANA
Lowline Large
www.fantasticfurniture.com.au
Version 1.0
REQUIRED
TWO PEOPLE

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.

Top Panel
(P1)
Back Panel
(P11)
Side
Panel
(P5)
Side
Panel
(P5)
Bottom
Panel
(P2)
Left
Divider
(P3)
Shelf Panel
(P6)
LR
Leg
(P9)
LF : Left Front LR : Left Rear
RF : Right Front RR : Right Rear
RR
Leg
(P10)
RF
Leg
(P8)
LF Leg
(P7)
Right
Divider
(P4)
Left Door
(P12)
Right Door
(P13)
Parts list
Box 1: Top Panel (P1);
Bottom Panel (P2);
Left Divider (P3);
Right Divider (P4);
2 x Side Panels (P5);
Shelf Panel (P6);
LF Leg (P7); RF Leg (P8);
LR Leg (P9); RR Leg (P10);
Back Panel (P11);
Left Door (P12); Right Door (P13);
Drawer Front (P14);
Left Drawer Side (P15);
Right Drawer Side (P16);
Drawer Base (P17); Drawer Back (P18);
Drawer Support (P19);
www.fantasticfurniture.com.au PAGE 4
Left
Drawer Side
(P15)
Right
Drawer Side
(P16)
Drawer Back
(P18) Drawer
Base
(P17)
Drawer Front
(P14)
Hardware pack
What you need
to assemble the product
Additional Tools Required
Flat head screwdriver;
Phillips head screwdriver;
Hammer
DO NOT USE
1 x Allen
Key
(H19)
2 x Rubber
Stickers
(H20)
6 x Inside
Hexagonal
Bolts
(H18)
4 x Hinges
(H15) 24 x Timber
Screws
(H16)
22 x Cam
Bolts
(H3)
22 x Cam
Nuts
(H4)
10 x Small
Screws
(H5)
5 x Small
Cam Nuts
(H11)
5 x Small
Cam Bolts
(H10)
4 x Plastic
Glides
(H21)
8 x Round
Head Bolts
(H14)
1 x CR Runner
Track
(H7)
1 x CL Runner
Track
(H6)
4 x Handles
(H13)
1 x DR
Runner
(H9)
1 x DL
Runner
(H8)
6 x Long
Screws
(H12)
16 x Dowels
(H1)
Drawer
Support
(P19)
21 x Small
Dowels
(H2)
2 x Adjustable
Support Legs
(H17)

(P3)
(P4)
(P3)
(P4)
H3
Attach 4 x Cam Bolts (H3) into Dividers (P3, P4) using a Phillips head screwdriver.
4 x Cam Bolts
(H3)
You will need
Step 2
Phillips head
screwdriver
www.fantasticfurniture.com.au PAGE 5
1 x CL Runner
Track (H6)
You will need
Step 1
6 x Small
Screws (H5) Phillips head
screwdriver
1 x CR Runner
Track (H7)
Attach 1 x CL Runner Track (H6) to Left Divider (P3) with 3 x Small Screws (H5).
Attach 1 x CR Runner Track (H7) to Right Divider (P4) with 3 x Small Screws (H5).
H7
CR
H5
H6
CL
H5
H5
H5
H5
H5
H5
H5
H6
H7
H3
H3
H3
Raw edge
PVC edge

(P10)
(P3)
(P6)
(P4)
(P9)
(P8)
(P7)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
H4
H4
H2
H2
H4
H4
H3
H3
H3 H3
H3
H3
H3
H3
Attach 8 x Cam Bolts (H3) into Legs (P7, P8, P9, P10) using a Phillips head screwdriver.
Insert 4 x Small Dowels (H2) into the holes of Shelf Panel (P6) as shown.
Insert
4 x Cam Nuts (H4) into into the holes of Shelf Panel (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Dividers (P3, P4) to Shelf Panel (P6),
then tighten the cam nuts using a Flat head screwdriver.
8 x Cam Bolts
(H3)
You will need
Step 3
Phillips head
screwdriver
www.fantasticfurniture.com.au PAGE 6
You will need
Step 4
4 x Cam Nuts
(H4)
Flat head
screwdriver
Make sure raw edge
is facing up.
4 x Small
Dowels (H2)

Insert 4 x Small Dowels (H2) into the holes of Bottom Panel (P2) .
Attach Side Panels (P5) to to Bottom Panel (P2) with
2 x Inside Hexagonal Bolts (H18) using an Allen Key (H19).
Back panel slot
Insert 4 x Small Dowels (H2) into the holes of Bottom Panel (P2).
Attach Dividers (P3, P4) to Bottom Panel (P2) with
4 x Inside Hexagonal Bolts (H18) using an Allen Key (H19).
www.fantasticfurniture.com.au PAGE 7
You will need
Step 5
You will need
Step 6
1 x Allen
Key (H19)
(P5)
(P5)
(P2)
(P2)
(P4)
(P3)
H18
H2
H2
H2
H2
H2
H19
Make sure raw
edge is facing up.
H18
H19
H18
H18
H18
H18
2 x Inside
Hexagonal Bolts
(H18)
1 x Allen
Key (H19)
4 x Small
Dowels (H2)
4 x Inside
Hexagonal Bolts
(H18)
4 x Small
Dowels (H2)
Cam Nut hole
nearby top

Insert 4 x Dowels (H1) into the holes of Bottom Panel (P2).
Insert 4
x Cam Nuts (H4) into the holes of Bottom Panel (P2) and Side Panels (P5) .
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Legs (P9, P10) into place, then tighten the cam nuts using a Flat head screwdriver.
Carefully turn the frame over.
Insert 4 x Dowels (H1) into Bottom Panel (P2).
Insert 4
x Cam Nuts (H4) into the holes of Bottom Panel (P2) and Side Panels (P5) .
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Legs (P7, P8) into place, then tighten the cam nuts using a Flat head screwdriver.
www.fantasticfurniture.com.au PAGE 8
You will need
Step 8
You will need
Step 7
(P2)
(P7)
(P8)
(P5)
(P5)
H1
H1
H1
H4
H4
H4
PVC edge
is facing up. H4
4 x Cam Nuts
(H4)
Flat head
screwdriver
REQUIRED
TWO PEOPLE
4 x Dowels
(H1)
4 x Cam Nuts
(H4)
Flat head
screwdriver
4 x Dowels
(H1)
(P2)
(P10)
(P9)
(P5)
(P5)
H1
H1
H1
H4
H4
H4
H4

www.fantasticfurniture.com.au PAGE 9
Carefully turn the frame over to an upright position.
Slide Back Panel (P11) into the grooves in Legs (P9, P10) and Bottom Panel (P2).
Insert 8 x Dowels (H1) into Legs (P7, P8, P9, P10).
Insert 8 x Small Dowels (H2) into Dividers (P3, P4) and Side Panels (P5) as shown.
You will need
Step 9
H21
H21
H21
H21
(P2)
H18
H17
H17
Twist 2 x Adjustable Support Legs (H17) to the bottom of Bottom Panel (P2) as shown.
Hammer 4 x Plastic Glides (H21) on Legs (P7, P8, P9, P10).
4 x Plastic
Glides (H21)
Hammer
(P7)
(P7)
(P8)
(P8)
You will need
Step 10
8 x Dowels
(H1)
REQUIRED
TWO PEOPLE
(P2)
(P11)
(P9)
(P9)
(P5)
(P5)
(P3)
(P4)
(P10)
H1 H1
H2 H2
H2H2
H2 H2
H2
H2
H1
H1
H1H1
H1
H1
8 x Small
Dowels (H2)
2 x Adjustable
Support Legs
(H17)
If the floor is uneven,
please twist the adjustable legs
to stabilize the table.

H4
H4
H4
H4
H4
H4
H4
(P1)
Insert 10 x Cam Nuts (H4) into the holes of Dividers (P3, P4),
Side Panels (P5) and Legs (P7, P8, P9, P10).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) to the frame and then tighten the cam nuts.
www.fantasticfurniture.com.au PAGE 10
You will need
Step 12
(P7)
(P8)
10 x Cam Nuts
(H4) Flat head screwdriver
(P9) (P5) (P3)
(P4)
H3
H3 H3 H3
H3
H3
H3
H3
H3
H3
Attach 10 x Cam Bolts (H3) into Top Panel (P1) using a Phillips head screwdriver
10 x Cam Bolts
(H3)
You will need
Step 11
Phillips head
screwdriver