fantastic furniture Aspect Bookcase User manual

Version 1.0
fantasticfurniture.com.au
Aspect
Bookcase

fantasticfurniture.com.au 2egaP 2egaP
Looks like you’ve found
your Fantastic!
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
fantasticfurniture.com.au
Recommended weight capacity : 15kgs/shelf
Warning: Ensure the wall strap is
attached to avoid serious injury.
To avoid any serious of fatal injury, a wall strap has been provided with
this product to prevent toppling. We strongly recommend that this
product is permanently fixed to the wall or other suitable surface. Fixing
of what fixing device to use.

Assembly checklist
Useful information
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Please see page 2 for any safety requirements or weight restrictions.
Page 3
fantasticfurniture.com.au

What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
1 x Washer
(H6)
Page 4fantasticfurniture.com.au
20 x Stickers
(H8)
1 x Wall
Strap Screw
(H7)
20 x Long
Screws
(H1)
20 x Cam
Bolts
(H2)
20 x Cam
Nuts
(H3)
1 x Wall Strap
(H5)
60 x Dowels
(H4)
Panel
(P5)
Panel
(P5)
LargeSide
Panel
(P5)
Panel
(P5)
Panel
(P5)
(P5)
Panel
(P6)
Panel
(P6)
Top Panel
(P1)
Base Panel
(P4)
Shelf Panel 1
(P2)
Shelf Panel 1
(P2)
Shelf Panel 2
(P3)
Shelf Panel 2
(P3)
Small Side Panel
(P6)
Large Back Panel
(P7)
Large Back Panel
(P7)
Small Side
Large Side
Panel
Large Back Panel
(P7)
Small Side Panel
(P6)
LargeSide
LargeSide
Large Side
Small Side
Large Side
Panel
(P8)
Small Back
Panel
(P8)
Small Back
Hammer
Parts list
Top Panel (P1);
2 x Shelf Panel 1 (P2);
2 x Shelf Panel 2 (P3);
Base Panel (P4);
6 x Large Side Panel(P5);
4 x Small Side Panel (P6);
3x Large Back Panel (P7);
2 x Small Back Panel (P8)
Hardware pack
8 x Plastic
Leg Studs
(H9)

Page 5
Step 1
Step 2
Insert 60 x Dowels (H4) into all Large & Small Side Panels (P5x6 & P6x4), all Large & Small
Back Panels (P7x3 & P8x2) as shown. Use the Hammer to gently tap the Dowels into place if
need be.
Attach 20 x Cam Bolts (H2) to Top Panel (P1) and Shelf Panels 1 & 2 (P2x2 &
P3x2) by tightening with the Phillips Head Screwdriver as shown.
20 x Cam Bolts
(H2)
fantasticfurniture.com.au
Phillips Head
Screwdriver
You will need
60 x Dowels
(H4)
(H4)
(H2)
You will need
(P1)
(P2)
x2
(P3)
x2
(H2)
Hammer
(P8)
x2
(P6)
x4
(P5)
x6
(P7)
x3

Page 6
Step 3
Step 4
Insert 4 x Cam Nuts (H3) into Large Side Panels (P5x2) as shown. Rotate the cam nuts so the
arrows point towards the incoming cam bolts. Attach Large Side Panels (P5x2) to Top Panel
(P1) by tightening all cam nuts with the Phillips Head Screwdriver.
Attach the top Large Back Panel (P7) with the informative label on it to Top Panel
(P1) as shown. Secure Shelf Panel 1 (P2) to Large Side Panels (P5x2) with 4 x
Long Screws (H1) by tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
4 x Long
Screws (H1)
You will need
Phillips Head
Screwdriver
(P5)
(P5)
(P1)
4 x Cam Nuts
(H3)
Turn to lock
(H3)
(P7)
(P5)
(P5)
(P2)
This is how a cam nut works......
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then turn
the cam nut so it
tightens over the bolt.
(H3)
(H3)
(H3)
(H3)
(H1)
(H1)
Ensure the laminated
edge of the panel is
facing this way
(P1)
Note: top Large Back Panel
(P7) with informative label
is to be used as shown.

Page 7
Step 5
Step 6
Insert 4 x Cam Nuts (H3) into Small Side Panels (P6x2) as shown. Rotate the cam nuts so
the arrows point towards the incoming cam bolts. Attach Small Side Panels (P6x2) to
Shelf Panel 1 (P2) by tightening all cam nuts with the Phillips Head Screwdriver.
Attach Small Back Panel (P8) to Shelf Panel 1 (P2) as shown. Secure Shelf Panel 2 (P3)
to Small Side Panels (P6x2) with 4 x Long Screws (H1) by tightening with the
Phillips Head Screwdriver.
fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
4 x Long
Screws (H1)
You will need
Phillips Head
Screwdriver
4 x Cam Nuts
(H3)
Turn to lock
(H3)
(P5)
(P5)
(P7)
(P1)
(P6)
(P6)
(P2)
(P5)
(P7)
(P1)
(P2)
(P8)
(P3)
(P6)
(P6)
(P5)
(H3)
(H3)
(H3)
(H3)
Ensure the laminated
edge of the panel is
facing this way
This is how a cam nut works......
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then turn
the cam nut so it
tightens over the bolt.

Page 8
Step 7
Step 8
Attach Large Back Panel (P7) to Shelf Panel 2 (P3) as shown. Secure Shelf Panel 1 (P2)
to Large Side Panels (P5x2) with 4 x Long Screws (H1) by tightening with the
Phillips Head Screwdriver.
fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
4 x Long
Screws (H1)
You will need
Phillips Head
Screwdriver
4 x Cam Nuts
(H3)
Insert 4 x Cam Nuts (H3) into Large Side Panels (P5x2) as shown. Rotate the cam nuts so
the arrows point towards the incoming cam bolts. Attach Large Side Panels (P5x2) to
Shelf Panel 2 (P3) by tightening all cam nuts with the Phillips Head Screwdriver.
Turn to lock
(H3)
(P1) (P5)
(P5)
(P5)
(P5)
(P7)
(P3)
(P2)
(P6)
(P8)
(P1) (P5)
(P5)
(P5)
(P5)
(P2)
(P7)
(P7)
(P3)
(P2)
(P6)
(P8)
(H3)
(H3)
(H3)
(H3)
This is how a cam nut works......
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then tu
the cam nut so it
tightens over the bol
Ensure the laminated
edge of the panel is
facing this way

Page 9
Step 9
Step 10
Insert 4 x Cam Nuts (H3) into Small Side Panels (P6x2) as shown. Rotate the cam nuts so
the arrows point towards the incoming cam bolts. Attach Small Side Panels (P6x2) to
Shelf Panel 1 (P2) by tightening all cam nuts with the Phillips Head Screwdriver.
Attach Small Back Panel (P8) to Shelf Panel 1 (P2) as shown. Secure Shelf Panel 2 (P3)
to Small Side Panels (P6x2) with 4 x Long Screws (H1) by tightening with the
Phillips Head Screwdriver.
fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
4 x Long
Screws (H1)
You will need
Phillips Head
Screwdriver
4 x Cam Nuts
(H3)
Turn to lock
(H3)
(P5)
(P5)
(P5)
(P5)
(P7)
(P7)
(P1) (P8)
(P2)
(P2)
(P3)
(P6)
(P6)
(P6)
(P5)
(P7)
(P1)
(P2)
(P2)
(P8)
(P8)
(P3)
(P3)
(P6)
(P6)
(P5)
(P5)
(P7)
(P5)
(H3)
(H3)
(H3)
(H3)
Ensure the laminated
edge of the panel is
facing this way
This is how a cam nut works......
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then tu
the cam nut so it
tightens over the bol

Page 10
Step 11
Step 12
Attach Large Back Panel (P7) to Shelf Panel 2 (P3) as shown. Secure Base Panel (P4)
to Large Side Panels (P5x2) with 4 x Long Screws (H1) by tightening with the
Phillips Head Screwdriver.
fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
4 x Long
Screws (H1)
You will need
Phillips Head
Screwdriver
4 x Cam Nuts
(H3)
Insert 4 x Cam Nuts (H3) into Large Side Panels (P5x2) as shown. Rotate the cam nuts so
the arrows point towards the incoming cam bolts. Attach Large Side Panels (P5x2) to
Shelf Panel 2 (P3) by tightening all cam nuts with the Phillips Head Screwdriver.
Turn to lock
(H3)
This is how a cam nut works......
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then tu
the cam nut so it
tightens over the bol
(P1) (P5)
(P5)
(P7)
(P5)
(P5)
(P7)
(P5)
(P5)
(P3)
(P3)
(P2)
(P6)
(P8)
(P2)
(P6)
(P8)
(P1) (P5)
(P5)
(P7)
(P5)
(P5)
(P7)
(P5)
(P5) (P7)
(P3)
(P3)
(P2)
(P6)
(P8)
(P2)
(P4)
(P6)
(P8)
(H3)
(H3)
(H3)
(H3)
Ensure the laminated
edge of the panel is
facing this way