fantastic furniture BOBBI User manual

Assembly Instructions
BOBBI
BUNK
Ver1.1

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws（leave slightly
loose.When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.


What you Need
To Assemble the Body
4x Round
End Cap
(H1)
67x Bolt
M6 x 15MM
(H2)
6x Bolt
M6 x 40MM
(H3)
4x Round
Stoppers
(H4)
2x Allen Key(M4)
(H5)
Page 3
Please make sure you have all these parts before you start.
Front
Guard
Rail
(P1)
Upper Post
(P7)
Upper Post
(P4)
4 pcs
Mid Post
(P8)
2 pcs
End Rail
(P20)
Lower Post
(P10)
Front Rail
(P13)
3 pcs
Ladder Rung
(P17)
Lower Post
(P9)
Ladder
Post
(P16)
3x Base
Mesh
(P19)
Lower Post
(P11)
Back Rail
(P14)
Upper Post
(P5)
Lower Post
(P12)
Ladder
Post
(P15)
Back Guard Rail
(P2)
3x Top
Mesh
(P18)
2x End Panel
(P3)
Upper Post
(P6)
(Tools not provided)
Mallet

page 4
Step 1
You will need:
Step 2
(P3)
(P7)
(P4)
(H2)
(H2)
(H2)
(H2)
(P3)
(P6)
(P5)
(H2)
(H2)
(H2)
(H2)
(
(
8x Bolt
M6 x 15MM
(H2)
(H2)
(H2)
You will need:
4 x Round
Stoppers
(H4)
8x Bolt
M6x 15MM
(H2)
(P11)
(P8)
(P9)
(P8)
(H4)
(H4)
(P10)
(P12)
(P8)
(P8)
(H4)
(H4)
（H2）
（H2）
（H2）
（H2）
（H2）
（H2）
（H2）
（H2）
（H2）
Left End
Left End
Right End
Right End
Attach Upper Posts (P4 & P7) to End Panel (P3) using 4x Bolts (H2).
Repeat same for Right End as shown.
Connect Lower Post (P10) and Mid Post (P8) to the Upper Post as shown.
Attach using 2x Bolts (H2).Repeat for each Post as shown. Insert 4x Round Stopper (H4)
to Lower Posts(P9 & P10 & P11 & P12).
Note:
Position of these holes important


Step 3
You will need:
16x Bolt
M6x 15MM
(H2)
Step 4
You will need:
5x Bolt
M6x 15MM
(H2)
(P20)
(P13)
(P14)
(P20)
Page 5
(H2)
(H2)
(P1)
(P2)
(P15) (P16)
You will need:
6x Bolt
M6x 15MM
(H2)
Step 5 （P3）
(H2)
(P2)
（P7)
(P4)
(H2) (P1)
Connect 2x End Rails (P20) to the Lower Posts using 8x Bolts (H2).
Attach Front Rail (P13) and Back Rail (P14) to the Lower Posts using 8x Bolts (H2).
Insert Ladder Posts (P15 & P16) into the holes on the Front Rail. Then lower Front Guard Rail (P1) onto
ladder posts and attach Front Guard Rail to Upper Posts using 5x Bolts (H2).
Attach Back Guard Rail (P2) to the Upper Posts using 6x Bolts (H2).
Note：Postion of hole for ladder.
short to top
long to bottom
(H2)
(H2)


Step 6
You will need:
6x Bolt
M6x 40MM
(H4)
（H4）
（P17）
（P17）
（P17）
（P17）
Page 6
You will need:
(H2)
(H2)
(P18)
(P18)
(P19)
Step 8
Connect 3x Ladder Rungs（P17）to the Ladder Side Post (P15 & P16) using 6x Bolts (H4).
24x Bolts
M6 x 15MM
(H2)
Locate the Top Mesh Base (P18) into the Guard Rails and Tighten using 12x Bolts (H2) as shown.
Locate the Bottom Mesh Base (P19) into the Front Rail and Back Rails and tighten using 12x Bolts (H2)
as shown.

Page 7
Step 10
The job is now complete!
In the interest of our environment
Please dispose of all packaging thoughtfully.
(H1)
(H1)
(H1)
(H1)
You will need:
Fully tighten all bolts.
Insert 4x Round End Cap (H1) to the Upper Post.
4x Round
End Cap
(H1)