fantastic furniture COMO User manual

Version 1.0
COMO
DESK CORNER
fantasticfurniture.com.au

fantasticfurniture.com.au PAGE 2
Looks like you’ve found
your Fantastic!
Love it? Share it!
Fantastic buy! Share how it looks at home for your
chance to win a $250 Fantastic Furniture Gift Card!
fantasticfurniture
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
Recommended weight capacity : 50kgs.

PAGE 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Top Panel (P2):
Drawer Left Side
Panel (P3);
Drawer Right Side
Panel (P4);
Shelf Panel (P5);
2 x Rail (P6);
2 x Rail (P7);
Rail (P8);
Drawer Back Panel (P9);
Back Panel (P10);
Left Side Panel (P11);
Right Side Panel (P12);
Side Back Panel (P13);
2 x Drawer Fronts (P14)
2 x Left Drawer Sides (P15);
2 x Right Drawer Sides (P16);
2 x Drawer Bases (P17):
2 x Drawer Backs (P18)
Hardware pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
PAGE 4
DO NOT USE
fantasticfurniture.com.au
Top Panel
(P1)
Right Side
Panel
(P12)
Drawer
Left Side
Panel
(P3)
Drawer
Right Side
Panel
(P4)
Left
Side
Panel
(P11)
Rail
(P6)
Rail
(P6)
Rail
(P7)
Rail
(P8)
Rail
(P7)
Shelf
Panel
(P5)
Top Panel
(P2)
Drawer
Back Panel
(P9)
Back
Panel
(P10)
Side
Back
Panel
(P13)
Left Drawer
Side
(P15) Drawer Front
(P14)
x 2
Right Drawer
Side
(P16)
Drawer Back
(P18)
Drawer Base
(P17)
36 x Dowels
(H1)
8 x Long
Screws
(H2)
32 x Small
Screws
(H5)
2 x CL Runner
Tracks
(H6)
33 x Cam Bolts
(H3)
33 x Cam Nuts
(H4)
8 x Small
Cam Nuts
(H11)
2 x Connect
Plates
(H13)
2 x Bolts
(H14)
2 x CR Runner
Tracks
(H7)
2 x DL Runners
(H8)
2 x DR Runners
(H9)
8 x Small
Cam Bolts
(H10)
3 x Long
Dowels
(H12)
8 x Plastic
Glides
(H15)

2 x CL Runner
Tracks (H6)
You will need
Step 1
Attach 2 x CR Runner Tracks (H7) to Drawer Right Side Panel (P4) with 6 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
6 x Small
Screws (H5)
Phillips Head
Screwdriver
6 x Small
Screws (H5)
2 x CR Runner
Tracks (H7)
Insert 10 x Dowels (H1) into Drawer Left Side
Panel (P3) as shown. Attach 10 x Cam Bolts (H3) to Drawer Left & Right Side Panels
(P3&P4) by tightening with the Phillips Head Screwdriver.
10 x Dowels
(H1)
10 x Cam Bolts
(H3)
(P4)
(P3)
H1
H1
H1
H1
H1
H1 H1 H1
H3
H3
H3
H3
H3
H3 H3
H3
H3
PAGE 5
fantasticfurniture.com.au
Step 2
You will need
Attach 2 x CL Runner Tracks (H6) to Drawer Left Side Panel (P3) with 6 x Small Screws (H5) by
tightening with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
Step 3
You will need
Phillips Head
Screwdriver
H5
H5
H5
H5
H5
H5
H6
H6
(P3)
H6
CL
H5
H5
H5
H5 H7
H7
H5
H5
H5
(P4)
H7
CR
H5

You will need
Step 4
Insert 3 x Cam Nuts (H4) into Shelf Panel (P5). Rotate the cam nuts so the arrows
point towards the incoming cam bolts. Attach Shelf Panel (P5) to Drawer Left Side
Panel (P3) by tightening all cam nuts with the Phillips Head Screwdriver. Attach
Rail (P8) to Drawer Left Side Panel (P3) as shown.
Step 5
You will need
Insert 2 x Cam Nuts (H4) into Rails (P7x2) as shown. Rotate the cam nuts so
the arrows point towards the incoming cam bolts. Attach Rails (P7x2) to Drawer
Left Side Panel (P3) by tightening all cam nuts with the Phillips Head Screwdriver.
Attach Rails (P6x2) to Drawer Left Side Panel (P3) as shown.
Phillips Head
Screwdriver
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
H4
2 x Cam Nuts
(H4)
3 x Cam Nuts
(H4)
(P3)
(P6)
(P6)
(P7)
(P7)
H4
H4
(P3)
(P8)
(P5)
H4
H4
H4
PAGE 6
fantasticfurniture.com.au

Step 7
You will need
Step 6
Insert 10 x Dowels (H1) into
Shelf Panel (P5) and Rails (P6x2,P7x2&P8).
Insert 3 x Cam Nuts (H4) into Shelf Panel (P5)
and 2 x Cam Nuts into Rails (P7x2) as shown.
Rotate the cam nuts so the arrows point towards
the incoming cam bolts. Attach Drawer Right Side
Panel (P4) by tightening all cam nuts with the Phillips Head
Screwdriver. Secure 4 x Plastic Glides (H15) to the bottom of
Drawer Left & Right Side Panels (P3&P4) with the Hammer, approximately
2cm from the end of each panel as shown.
Slide Drawer Back Panel (P9) into the grooves of Shelf Panel (P5) and Rail (P8). Ensure the
laminated side of the Back Panel is facing outwards.
Phillips Head
Screwdriver
Hammer
10 x Dowels
(H1)
5 x Cam Nuts
(H4)
4 x Plastic
Glides (H15)
(P9)
(P8)
(P5)
fantasticfurniture.com.au PAGE 7
(P10)
(P3)
(P4)
(P6) (P6) (P7)
(P8)
(P7)
(P5)
H15
H15
H15
H15
H1 H1
H1
H1 H1
H1
H1
H1 H1
H4
H4
H4
H4
H4
H15
2cm

Attach 17 x Cam Bolts (H3) to Top Panels (P1&P2) by tightening with the Phillips
Head Screwdriver. Attach 2 x Connect Plates (H13) to Top Panel (P1) with 6 x
Small Screws (H5) by tightening with the Phillips Head Screwdriver.
Stand the partially assembled drawer unit upright as shown.
Insert 2 x Dowels (H1) into Drawer Right Side Panel (P4) and attach
2 x Cam Bolts (H3) by tightening with the Phillips Head Screwdriver.
Insert 2 x Cam Nuts (H4) into Back Panel (P10) as shown. Rotate the cam
nuts so the arrows point towards the incoming cam bolts. Attach Back Panel (P10)
to Drawer Right Side Panel (P4) by tightening cam nuts with the Phillips Head Screwdriver.
Step 8
You will need
You will need
Step 9
Phillips Head
Screwdriver
2 x Cam Bolts
(H3)
17 x Cam Bolts
(H3)
2 x Connect
Plates (H13)
6 x Small
Screws (H5)
fantasticfurniture.com.au PAGE 8
Phillips Head
Screwdriver
2 x Dowels
(H1)
2 x Cam Nuts
(H4)
(P10)
(P4)
H3
H3
H1
H1 H4
H4
(P1)
(P2)
H3
H3
H3
H3
H3 H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H5
H5
H13
H13
H5H5 H5
H5
H13

You will need
Step 11
Attach 4 x Cam Bolts (H3) to Left & Right Side Panels (P11&12). Secure 4 x
Plastic Glides (H15) to the bottom of Left & Right Side Panels (P11&P12) with
the Hammer, approximately 2cm from the end of each panel as shown.
Insert 6 x Dowels (H1) and 8 x Cam Nuts (H4) into
Drawer Left & Right Side Panels (P3&P4) and Back
Panel (P10) as shown. Rotate the cam nuts so the arrows
point towards the incoming cam bolts. Attach Top Panel (P1) to partially assembled
drawer unit by tightening cam nuts with the Phillips Head Screwdriver. Ensure the
Top Panel is sitting flush with the unit before securing.
You will need
Step 10
Phillips Head
Screwdriver
8 x Cam Nuts
(H4)
6 x Dowels
(H1)
4 x Cam Bolts
(H3)
Phillips Head
Screwdriver
fantasticfurniture.com.au PAGE 9
(P1)
(P10)
(P4)
(P3)
H1
H1
H1
H1
H1
H4
H4
H4
H1
H4
H4
H4
H4
H4
(P12)
(P11)
H3 H3
H3
H3
H15
H15
H15
H15
Hammer
4 x Plastic
Glides (H15)
Required
Two People
2cm
H15

You will need
Step 13
Carefully turn the partially assembled desk unit upright as shown. Insert 4 x Dowels (H1)
into Left & Right Side Panels (P11&P12) and insert 9 x Cam Nuts (H4) into Side Back
Panel (P13) and Left & Right Side Panels (P11&P12) as shown. Rotate the cam nuts
so the arrows point towards the incoming cam bolts. Attach Top Panel (P2) by
tightening cam nuts with the Phillips Head Screwdriver.
Insert 4 x Dowels (H1) & 4 x
Cam Nuts (H4) into Back
Panel (P13). Rotate the cam nuts
so the arrows point towards the
incoming cam bolts. Secure Left & Right Side Panels (P11&P12) to Side Back Panel (P10) by
tightening cam nuts with the Phillips Head Screwdriver.
You will need
Step 12
Phillips Head
Screwdriver
4 x Cam Nuts
(H4)
4 x Dowels
(H1)
Phillips Head
Screwdriver
(P2)
(P11)
(P12)
(P13)
H1
H1
H4
H4
H4 H4
H4 H4
9 x Cam Nuts
(H4)
4 x Dowels
(H1)
fantasticfurniture.com.au PAGE 10
(P12)
(P11)
(P13) H4
H1
H1
H1
H1
H4
H4
H4
Required
Two People