fantastic furniture Bridge User manual

Bridge
Ent Unit

r

Unit Top(P1)
Unit Bottom(P2)
Right Panel(P3)
Left Panel(P4)
M-Left Panel(P5)
M-Right Panel(P6)
Middle Shelf(P7)
2 x Support Rail(P8)
M-Back Panel(P9)
2 x Back Panel(P10)
Left Door(P11)
Right Door(P12)
Hardware Pack
20 x Cam Bolts
(H1)
20 x Cam Nuts
(H2)
28 x Dowels
(H3)
4 x Hinges
(H4) 36 x Short Screws
(H5)
2 x Legs
(H6)
12 x Washers
(H7)
12 x Long Bolts
(H8)
1 x Allen Key
(H9) 4 x Levelling Feet
(H10)
12 x Wedges
(H11)
1 x Long Screw
(H12)
1 x Support Leg
(H13)
2 x Short Bolts
(H14)
2 x Washers
(H15)
1 x Wall Strap
(H16)
Rails

2 x Short Bolts
(H14)
1 x Allen Key
(H9)
2 x Legs
(H6)
12 x Washers
(H7)
12 x Long Bolts
(H8)
1 x Allen Key
(H9)
4 x Levelling Feet
(H10)
Using 2 x Short Bolts(H4) secure the Support Leg(H13) to the Unit Bottom(P2)
by tightening with Allen Key(H9).
Using 6 x Washers(H7) and 6 x Long Bolts(H8) secure the Table Leg(H6) to the
Unit Bottom(P2) by tightening with Allen Key(H9)
Repeat the previous step to attach the second Table Leg(H6).
Screw in 4 x Levelling Feet(H10) to the bottom of the Table Legs(H6)
Ensure the Levelling Feet are screwed in firmly.If your flooring surface is
uneven adjust the Levelling Feet accordingly.
1 x Support Leg
(H13)

8 x Cam Bolts
(H1)
8 x Dowels
(H3)
Phillips Head
Screwdriver
4 x Cam Bolts
(H1)
4 x Dowels
(H3)
Phillips Head
Screwdriver
Insert 8 x Dowels(H3) into Unit Bottom(P2) and secure 8 x Cam Bolts(H1)
into Unit Bottom(P2) by tightening with the Phillips Head Screwdriver.
Insert 2 x Dowels(H3) into M- Right Panel(P6) and secure 2 x Cam Bolts(H1) into
M-Right Panel(P6) by tightening with the Phillips Head Screwdriver.
Repeat previous step for M-Left Panel(P5).
(P2)

Phillips Head
Screwdriver
2 x Cam Nuts
(H2)
2 x Cam Nuts
(H2)
Phillips Head
Screwdriver
Insert 2 x Cam Nuts(H2) into Middle Shelf(P7) as shown.Rotate the cam nuts
so the arrows point towards the incoming cam bolts.
Attach Middle Shelf(P7) to M-Right Panel(P6) by tightening the Cam Nuts(H2)
with the Phillips Head Screwdriver
Insert 2 x Cam Nuts(H2) into Middle Shelf(P7) as shown.Rotate the cam
nuts so the arrows point towards the incoming cam bolts.
Attach Middle Shelf(P7) to M-Left Panel(P5) by tightening the Cam Nuts
(H2) with the Phillips Head Screwdriver

Page 8
7
8
4 x Cam Nuts
(H2)
Phillips Head
Screwdriver
Insert 4 x Cam Nuts(H2) into M-Left Panel(P5) and M-Right Panel(P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Unit Bottom(P2) to M-Left Panel(P5) and M-Right Panel(P6)
by tightening the Cam Nuts(H2) with the Phillips Head Screwdriver
Slide M-Back Panel(P9) into the groove of M-Left Panel(P5) and
M-Right Panel(P6) as shown.

Page 9
9
10
Phillips Head
Screwdriver
2 x Cam Nuts
(H2)
4 x Dowels
(H3)
Insert 2 x Dowels(H3) into M-Right Panel(P6) and Support Rail(P8)
Insert 2 x Dowels(H3) into Right Panel(P3) and Support Rail(P8)
Insert 2 x Cam Nuts(H2) into Right Panel(P3).Rotate the cam nuts
so the arrows point towards the incoming cam bolts.
Attach Right Panel(P3) to Unit Bottom(P2) by tightening the Cam
Nuts(H2) with the Phillips Head Screwdriver.
Slide one Back Panel(P10) into the groove of M-Right Panel(P6)
and Right Panel(P3) as shown.
(P2)
(P10)
(P6)
(P3)

Page 10
11
12
Phillips Head
Screwdriver
2 x Cam Nuts
(H2)
4 x Dowels
(H3)
Insert 2 x Dowels(H3) into M-Left Panel(P5) and Support Rail(P8)
Insert 2 x Dowels(H3) into Left Panel(P4) and Support Rail(P8)
Insert 2 x Cam Nuts(H2) into left Panel(P4).Rotate the cam nuts so
the arrows point towards the incoming cam bolts.
Attach Left Panel(P4) to Unit Bottom(P2) by tightening the Cam
Nuts(H2) with the Phillips Head Screwdriver.
Slide another Back Panel(P10) into the groove of M-left Panel(P5) and
left Panel(P4) as shown.
(P4)
(P5)
(P4)
(P10) (P5)