fantastic furniture COMO ROBE 2 DOOR User manual

Assembly Instructions
ROBE 2 DOOR
COMO

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws (leave slightly
loose).When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

Page 3
What You Need
To Assemble The Body
Top Panel
(P1)
Right Side
Panel
(P3)
Right
Door
(P13)
Left
Door
(P12)
Left Drawer
Side
(P15)
Drawer Front
(P14)
x 2
Right Drawer
Side (P16)
Drawer Back
(P18) Drawer Base
(P17)
Support
Rail
(P19)
Left Side
Panel
(P2)
Rail
(P8)
Rail
(P5)
Rail
(P6)
Rail
(P6)
Rail
(P7)
Back
Panel
(P20)
Back
Panel
(P9)
Shelf
Panel
(P4)
Long Connect
Stick (P10)
Short Connect
Stick (P11)
(Tools not provided)
Flat BladeScrewdriver
Phillips Head Screwdriver
Mallet
26 x Dowels
(H1)
12 x Long
Screws
(H2)
58 x Small
Screws
(H5)
28 x Timber
Screws
(H17)
2 x Clothes
Hanger Support
(H14)
1 x Clothes
Hanger
(H15)
4 x Hinges
(H16)
2 x CL Runner
Tracks
(H6)
2 x CR Runner
Tracks
(H7)
15 x Cam
Bolts
(H3)
15 x Cam
Nuts
(H4)
10 x Small
Cam Nuts
(H11)
2 x Catapult
Base
(H12)
2 x Catapult
(H13)
2 x DL Runners
(H8)
2 x DR Runners
(H9)
10 x Small
Cam Bolts
(H10)
Please make sure you have all these parts before you start.
(H19)
1 x Screw
(H18)
1 x Safety Strap 2 x Washers
(H20)
1x Safety Strap Set
6 x Plastic
Glides
(H21)
1 x Wedge
(H22)
2 x Iron Sheet
(H23)

Page 4
Step 1
You will need:
2 x CL Runner
Tracks
(H6)
2 x CR Runner
Tracks
(H7)
12 x Dowels
(H1)
12 x Small
Screws
(H5)
Insert 12 x Dowels (H1) into Left Side Panel (P2).
Attach 7 x Cam Bolts (H3) to Left Side Panel (P2) as shown.
Attach 2 x CL Runner Tracks (H6) to Left Side Panel (P2) and 2 x CR Runner Tracks (H7) to
Right Side Panel (P3) with 12 x Small Screws (H5).
(P2)
(P3)
H5
H5
H5
H5
H5
H5
H6
H6
H5
H5
H5 H7
H7
H5
H5
H5
Step 2
You will need:
7 x Cam Bolts
(H3)
H3
H3
H1
H1
H1
H1
H1 H1
H1 H1
H1
H1
H1
H1
H1
H1
H1
H1
H1 H1
H1
H3
H3
H3
H3
H3
(P2)
H7
H7
H5
H5
H5 H5
H5
H5
H5
H5
H5
H5
H5
H5
H6
H6
H3
H3
H3
H6
CL
H5
H7
CR
H5

4 x Small
Screws
(H5)
Attach 1 x Cam Bolt (H3) into the hole of Rail (P8) as shown.
Insert 1 x Cam Nut (H4) into the hole of Shelf Panel (P4).
Rotate the cam nuts so the arrows point towards the incoming cam bolt.
Push Shelf Panel (P4) into place and tighten the cam nut.
Attach 7 x Cam Bolts (H3) to Right Side Panel (P3) as shown.
1 x Cam Nut
(H4)
7 x Cam Bolts
(H3)
Page 5
Step 3
You will need:
Attach 2 x Catapult Base (H12) to Top Panel (P1)
with 4 x Small Screws (H5) as shown,then insert
2 x Catapult (H13) into the catapult base.
Step 4
You will need:
1 x Cam Bolt
(H3)
2 x Catapult
(H13)
Step 5
You will need:
2 x Catapult
Base
(H12)
H3
H3
H3
H3
H3
H3
H3
(P3)
H3
H3
H3
H3
H3
(P8)
(P4)
(P1)
H4
H12
H13
H5
H12 H12
H5
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.

Step 6
You will need:
Page 6
2 x Cam Nuts
(H4)
Insert 2 x Cam Nuts (H4) into the holes of 2 x Rails (P6).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach
2 x Rails (P6) to Left Side Panel (P2), then tighten the cam nuts.
(P2)
(P6)
(P6)
H4
H4
Step 7
You will need:
Insert 1 x Cam Nut (H4) into the hole of Rail (P7).
Rotate the cam nut so the arrow point towards the incoming cam bolt.
Attach
Rails (P5,P7) to Left Side Panel (P2), then tighten the cam nuts.
1 x Cam Nuts
(H4)
(P2)
(P5)
(P7)
H4

Step 8
You will need:
Page 7
Step 9
You will need:
7 x Cam Nuts
(H4)
Insert 4 x Cam Nuts (H4) into the holes of Panels (P1,P4,P8).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach
Panels (P1,P4,P8) to Left Side Panel (P2), then tighten the cam nuts.
Insert 12 x Dowels (H1) into the holes of
Panels (P1,P4), 2 x Rails (P6) and Rails (P5,P7,P8).
Insert 7 x Cam Nuts (H4) into the holes of Panels (P1,P4),
2 x Rails (P6) and Rail (P7).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Right Side Panel (P3) into place and tighten the cam nuts.
4 x Cam Nuts
(H4)
(P7)
(P4)
(P2)
(P3)
(P6)
(P6)
(P5)
(P1)
(P8)
H4
H4
H4
H4
H4
H4
(P2)
(P1)
(P4)
(P8)
H4
H4
H4
H4
12 x Dowels
(H1)
H1
H1
H1
H1
H1
H1
H1
H1
H1
H1
H4

H5
H16
H16
H16
H16
H17
H17
H5
Step 10
28 x Small
Screws
(H5)
Page 8
You will need:
(P2)
(P3)
(P9)
(P12)
(P13)
(P20)
(P10)
(P11)
You will need:
4 x Hinges
(H16)
Step 11
Join Back Panels (P9,P20) with Long Connect Stick (P10) and Short Connect Stick (P11),
then put into the groove on the back of the carcase, colour faces inside,
attach it with 28 x Small Screws (H5). Then hammer 6 x Plastic Glides (H21).
Attach 2 x Iron Sheet (H23) to Doors (P12,P13) with 2 x Small Screws (H5).
Attach 4 x Hinges (H16) to Doors (P12,P13) with 8 x Timber Screws (H17).
8 x Timber
Screws
(H17)
2 x Small
Screws
(H5)
2 x Iron
Sheet
(H23)
H17
H17
H17
H17
H17
H23
H23
H5
H5
H17
H16
H17 H17
H21
H21
H21
H21
H21
H21
6 x Plastic
Glides
(H21)
H21
20mm
CAREFULLY ROLL
ONTO FRONT

H16
(P2)
(P3)
(P2)
(P13)
(P12)
(P3)
Page 9
Step 13
You will need:
1 x Clothes
Hanger
(H15)
Attach 2 x Clothes Hanger Support (H14) to Side Panels (P2) and (P3) with 4 x Timber Screws (H17),
then put 1 x Clothes Hanger (H15) into the clothes hanger support.
Attach Left Door (P12) to Left Side Panel (P2) and Right Door (P13)
to Right Side Panel (P3) with 16 x Timber Screws (H17).
H15
H17 H14
H17
You will need:
2 x Clothes
Hanger Support
(H14)
Step 12
4 x Timber
Screws
(H17)
16 x Timber
Screws
(H17)
H17
H17
CAREFULLY LIFT
ONTO FEET

H10 H10
H11
H11
H11
H11
H11
1 x Dowel
(H1)
Page 10
Step 14
You will need:
5 x Small Cam
Bolts
(H10)
Step 15
Step 16
You will need:
(P14)
(P14)
(P19)
(P17)
(P15)
(P16)
(P14)
(P15)
(P16)
Insert 1 x Dowel (H1) into Drawer Front (P14).
Attach 5 x Small Cam Bolts (H10) as shown.
5 x Small Cam
Nuts
(H11)
Slide Drawer Base (P17) into the groove
in Drawer Sides (P15) and (P16).
Insert 5 x Small Cam Nuts (H11) into the holes of Drawer Sides (P15,P16) and
Support Rail (P19).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Side (P15,P16) and Support Rail (P19) into place and tighten the cam nuts.
H10
H10
H10
H1
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.