fantastic furniture Eden Clothes Rack User manual

Eden
Utility 1 Shelf Clothes Rack
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 15kg/hanging rail.
20kg/shelf.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Page 2

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
2 x Top/Base Panels (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Shelf Panel (P4);
2 x Back Panels (P5);
2 x Rails (P6);
2 x Support Rods (P7);
Back Panel (P8)
Hardware pack
Top/Base Panel
(P1)
Top/Base Panel
(P1)
Shelf Panel
(P4)
Right Side
Panel (P3)
Left Side
Panel (P2)
Rail
(P6) Rail
(P6)
Support
Rod
(P7)
Support
Rod
(P7)
Back
Panel
(P5)
Back
Panel
(P8)
Back
Panel
(P5)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
16 x Dowels
(H1)
16 x Cam
Bolts
(H3)
16 x Cam
Nuts
(H4)
2 x Hanging Rail
Support
(H5)
1 x Hanging Rail
(H6)
10 x Wedges
(H8)
4 x Plastic
Glides
(H7)
10 x Long
Screws
(H9)
1 x Safety
Strap
Screw
(H11)
1 x Safety
Strap
(H10)
2 x Washers
(H12)
8 x Flat Head
Screws
(H2)

8 x Cam Bolts
(H3)
You will need
Step 1
Step 2
You will need
Attach 8 x Cam Bolts (H3) to Left Side Panel (P2) as shown by tightening with the
Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
8 x Cam Bolts
(H3)
Phillips Head
Screwdriver
Phillips Head
Screwdriver
Attach 8 x Cam Bolts (H3) to Right Side Panel (P3) as shown by tightening with the
Phillips Head Screwdriver.
H3
H3
H3
H3
H3
H3 H3
H3
H3
H3
H3
H3
H3H3
H3 H3
(P3)
(P2)

Slide Back Panels (P5 x 2 & P8) into the grooves
of Top/Base Panels (P1 x 2), Shelf Panel (P4) and Left Side Panel (P2).
Ensure laminated
side of panels are
facing inwards.
(P1)
(P1)
(P1) (P5)
(P5)
(P8)
(P2)
(P1)
fantasticfurniture.com.au Page 6
Step 4
Step 3
You will need
Phillips Head
Screwdriver
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
Insert 8 x Dowels (H1) into Left Side Panel (P2).
Insert 8 x Cam Nuts (H4) into Top/Base Panels (P1 x 2), Shelf Panel (P4)
and Rails (P6 x 2). Rotate the nuts so the arrows point towards the incoming
bolts. Attach Top/Base Panels (P1 x 2), Shelf Panel (P4) and Rails (P6 x 2)
to Left Side Panel (P2) by tightening all nuts with the Phillips Head Screwdriver.
H4 H4
H1
H1
H1
H1
H4
(P6)
(P6)
(P2)
Ensure the grooves in the Top/Base
Panels (P1 x 2) located at the back of
the unit.
Grooves for
back panels
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
(P4)
(P4)
H1
H1
H4

Step 5
You will need
Step 6
You will need
Secure 4 x Plastic Glides (H7) to the bottom of Left & Right Side Panels (P2 & P3)
as shown using the Hammer.
fantasticfurniture.com.au Page 7
Phillips Head
Screwdriver
Hammer
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
4 x Plastic
Glides (H7)
Insert 8 x Dowels (H1) into
Top/Base Panels (P1 x 2), Shelf Panel (P4)
and Rails (P6 x 2). Insert 8 x Cam Nuts (H4) into Top/Base
Panels (P1 x 2), Shelf Panel (P4) and Rails (P6 x 2). Rotate the
nuts so the arrows point towards the incoming bolts. Attach
Right Side Panel (P3) to Top/Base Panels (P1 x 2), Shelf Panel (P4)
and Rails (P6 x 2) by tightening all nuts with the Phillips Head Screwdriver.
(P2)
(P3)
(P1)
(P1)
(P3)
(P6)
(P6)
H1
H1
H1
H1 H1
H1
H4
H4
H4
H1
H4
H4
H4
H7
H7
H7
H7
(P4)

You will need
Phillips Head
Screwdriver
Step 8
Secure 2 x Hanging Rail Supports (H5)
to Left & Right Side Panels (P2 & P3)
with 4 x Flat Head Screws (H2) as shown
by tightening with the Phillips
Head Screwdriver. Place the
Hanging Rail (H6) in the unit by
resting it on the Hanging Rail
Supports (H5 x 2).
fantasticfurniture.com.au Page 8
H5
H6
H2
H2
H2
H2
H2
H2
H2
Attach 2 x Support Rods (P7) to Left & Right Side Panel (P2 & P3) with 4 x Flat Head Screws (H2)
as shown by tightening with the Phillips Head Screwdriver.
(P2)
(P7)
(P7)
(P2)
(P3)
(P3)
You will need
Step 7
Phillips Head
Screwdriver
2 x Hanging Rail
Support (H5)
1 x Hanging
Rail (H6)
4 x Flat Head
Screws (H2)
4 x Flat Head
Screws (H2)
H6

Secure Back Panels (P5 x 2 & P8) in place with 10 x Wedges (H8) and
10 x Long Screws (H9) by tightening with the Phillips Head Screwdriver.
You will need
Step 9
10 x Wedges
(H8)
10 x Long
Screws (H9)
Phillips Head
Screwdriver
Attach the Safety Strap (H10) to the Top Panel (P1) with 1 x Safety Strap
Screw (H11) & 1 x Washer (H12) by tightening with the Phillips Head Screwdriver.
You will need
Step 10
Phillips Head
Screwdriver
1 x Safety Strap
Screw (H11)
1 x Safety
Strap (H10)
1 x Washer
(H12)
fantasticfurniture.com.au Page 9
(P1)
(P2)
(P5)
(P5)
(P8)
(P3)
H8
H9
H10
H11
H12
We strongly advise that you
use the wall safety strap
provided to prevent the unit
toppling.
(P1)
(P2)
(P5)
(P5)
(P3)
H10
H11
H12

Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
fantasticfurniture.com.au Page 10
H12
wall
Screw
(P1)
Move the unit to the final position, and attach the safety strap to the wall securely. Make
sure it is firmly attached and snug fit.
Seek advice from a qualified
trades person on how to
attach this safety strap to
your specific wall.
You will need
Step 11
Phillips Head
Screwdriver
1 x Washer
(H12)
Screw and Wall Plug
are not provided.
Please use appropriate
fixtures for your wall.