fantastic furniture Bridge User manual

Bridge
Bed King Oak

1 x Headboard(P1)
1 x Right Side Panel (P2)
1 x Left Side Panel(P3)
1 x Footboard(P4)
2 x Side Rails(P5)
2 x Cross Bars(P6)
3 x Support Legs(P7)
1 x Centre Rail(P8)
15 x Centre Plastic Slat Caps(P9)
30 x Plastic Slat Caps(P10)
30 x Slats(P11)
2 x Legs(P12)
8 x Threaded Rods
(H1)
8 x Half Moon Nuts
(H2)
8 x Large Nuts
(H3)
52 x Short Bolts
(H4)
86 x Washers
(H5)
16 x Long Bolts
(H6)
12 x Bolts
(H7)
6 x Nuts
(H8)
4 x Levelling Feet
(H9)
1 x Allen key
(H10)
1 x Spanner
(H11)
Headboard
(P1)
Right Side Panel
(P2)
Left Side Panel
(P3)
Footboard
(P4)
Side Rails
(P5)
Support Legs
(P7)
Centre Rail
(P8)
Centre Plastic Slat Caps
(P9)
Plastic Slat Caps
(P10)
Legs
(P12)
Cross Bar
(P6)
Slats
(P11)
2 x Connectors
(H13)
2 x
(H14)
Connectors
Cross Bar
(P6)
1 x Spanner
(H12)

Step 1
Step 2
P1
P2
P3
P4
8 x
(H2)
Half Moon Nuts
1 x Spanner
(H11)
(H1)
(H1)
(H1)
(H2)
(H2)
(H3)
(H3)
(H11)
(H11)
8 x Large Nuts
(H3)
With assistance, carefully align and attach the right side panel (P2) between the headboard (P1) and footboard (P4).
Secure together using 8 x half moon nuts (H2) and 8 x large nuts, tightening with the spanner (H11).
Repeat this step to attach the left side panel (P3) to the headboard (P1) and footboard (P4).
(H1)
(H1)
(H1)
8 x Threaded Rods
(H1)
P1
(H1)
(H1)
(H1)
(H1)
P4
Attach 4 x threaded rods (H1) into the bottom of headboard (P1) and 4 x threaded rods (H1)
into the footboard (P4) by turning clockwise until secure.

Page 6
Step 3
Step 4
32 x Washers
(H5)
Allen Key
(H10)
32 x Short Bolts
(H4)
(H10) (H4)
(H5)
(H13)
(H14)
(H13)
(H14)
Attach the connectors (H13,H14) to each corner of the bed frame using 32 x short bolts (H4)
and 32 x washers (H5), tightening using allen key (H10).
4 x Levelling Feet
(H9)
Screw in 4 x levelling feet (H9) into the 2 x legs (P12) by turning clockwise until secure.
These can be adjusted as required to ensure assembled unit is level.
P12
(H9)
(H9)
(H9)
(H9)
2 x Connectors
(H13)
2 x
(H14)
Connectors

Page 7
16 x Washers
(H5)
Allen Key
(H10)
16 x Bolts
(H6)
Step 5
Step 6
P5
P5
(H5)
(H6)
With assistance, carefully turn the bed upright again.
Secure 1 x side rail (P5) to the right side panel (P2) using 8 x long bolts (H6)
and 8 x washers (H5), tightening using allen key (H10).
Repeat this step to secure the side rail (P5) to the left side panel (P3).
16 x Washers
(H5)
Allen Key
(H10)
16 x Short Bolts
(H4)
(H4)
(H5)
With assitance, carefully turn the bed over onto one side as pictured.
Connect the 2 x legs (P12) to the connectors (H13,H14)
using 16 x short bolts and 16 x washers (H5), completely tightening with the allen key (H10).
P12
P12
P2
P3

Page 8
Step 7
Step 8
4 x Washers
(H5)
Allen Key
(H10)
4 x Short Bolts
(H4)
(H4)
(H5)
Align the centre rail (P8) between the headboard (P1) and footboard (P4) as shown.
Secure the centre rail to the headboard (P1) and footboard (P4) using 4 x short bolts (H4)
and 4 x washers (H5), tightening with the allen key (H10).
P8
P7
P7
P7
6 x Bolts
(H7)
12 x Washers
(H5)
6 x Nuts
(H8)
1 x Allen Key
(H10)
(H7)
(H5)
(H5)
(H8)
Attach the 3 x support legs (P7) to the centre rail (P8) using 6 x bolts (H7),
12 x washers (H5) and 6 x nuts (H8), tightening using the allen key (H10) and spanner(H12).
1 x Spanner
(H12)
(H10)
(H12)
P8

Page 9
Step 9
Step 10
6 x Bolts
(H7)
6 x Washers
(H5)
1 x Alen key
(H10)
(H7)
(H5)
Attach the 2 x cross bars (P6) to the 2 x side rails (P5) and centre rail (P8) using
6 x bolts (H7) and 6 x washers (H5), tightening using the allen key (H10).
P6
P6
15 x Centre Plastic
Slat Caps
(P9)
30 x Plastic
Slat Caps
(P10)
30 x Slats
(P11)
Attach 2 x plastic slat caps (P10), 2 x slats (P11) and 1 x centre plastic slat cap together
as shown above.
Repeat this step for the other slats and caps.
P5
P8

Page 10
Step 11
Lower onto the assembled bed frame, pushing in the plastic slat caps (P10)
into the holes on the side rail, and the centre plastic slat caps (P9)
into the holes on the centre rail (P8). Apply downward pressure until you feel the caps pop
into place.