fantastic furniture Cove User manual

Cove
Lowboy 3 Drawer
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 15kg/Drawer.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Bottom Panel (P2);
Left Side Panel (P3);
Right Side Panel (P4);
2 x Back Panels (P5);
Rail (P6);
Rail (P7);
2 x Rails (P8);
4 x Legs (P9);
3 x Drawer Fronts (P10);
3 x Left Drawer Sides (P11);
3 x Right Drawer Sides (P12);
3 x Drawer Backs (P13);
3 x Drawer Bases (P14);
3 x Rails (P15)
Hardware pack
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
DO NOT USE
fantasticfurniture.com.au
Top Panel
(P1)
Left Side
Panel (P3)
Right Side
Panel (P4)
Bottom Panel
(P2)
Back
Panel (P5)
Rail
(P6)
Rail
(P7)
Rail
(P8)
Rail
(P8)
Leg
(P9)
Back
Panel (P5)
x4
x3
Left Drawer
Side (P11)
Right Drawer
Side (P12)
Drawer Back
(P13)
Drawer
Base
(P14)
Rail
(P15)
Drawer Front
(P10)
1 x Screw
(H15)
1 x Safety
Strap
(H14)
2 x Washers
(H16)
4 x Plastic
Glides
(H17)
16 x Dowels
(H1)
22 x Long Screws
(H2)
30 x Small
Screws
(H5)
3 x CL Runner
Tracks
(H6)
27 x Cam Bolts
(H3)
27 x Cam Nuts
(H4)
3 x CR Runner
Tracks
(H7)
3 x DL Runners
(H8)
3 x DR Runners
(H9)
8 x Wedges
(H12)
8 x Wedge
Screws
(H13)
20 x Screws
(H10)
4 x Brackets
(H11)

You will need
Step 1
Attach 3 x CR Runner Tracks (H7) to Right Side Panel (P4) with 9 x Small Screws (H5).
Attach 3 x CL Runner Tracks (H6) to Left Side Panel (P3) with 9 x Small Screws (H5).
Tighten with a Phillips Head Screwdriver. Attach 8 x Cam Bolts (H3) to Left &
Right Side Panel (P3 & P4) as shown. Tighten with a Phillips Head Screwdriver.
Phillips Head
Screwdriver
4 x Cam Bolts
(H3)
8 x Cam Bolts
(H3)
Page 5
fantasticfurniture.com.au
Step 2
You will need
Attach 4 x Cam Bolts (H3) to Top Panel (P1) as shown. Tighten with a Phillips Head Screwdriver.
(P3)
(P1)
(P4)
18 x Small
Screws (H5)
3 x CL Runner
Tracks (H6)
3 x CR Runner
Tracks (H7)
Phillips Head
Screwdriver
H7
CR
H5
H6
CL
H5
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H6
H6
H6
H7
H7
H7
H5
H5
H5
H5
H5
H5

You will need
Step 3
Insert 4 x Dowels (H1) into Rails
(P7, P8 x 2). Insert
4 x Cam Nuts (H4) into Rails
(P6, P8 x 2) as shown. Rotate
the cam nuts so the arrow points
towards the incoming cam bolts.
Attach Right Side Panel (P4) to Rails
(P6, P7, P8 x 2) by tightening with the Phillips Head Screwdriver.
Insert 4 x Dowels (H1) into Left Side Panel (P3). Insert 4 x Cam Nuts (H4) into Rails (P6, P8 x 2)
as shown. Rotate the cam nuts so the arrow points towards the incoming cam bolts. Attach
Rails (P6, P7, P8 x 2) to Left Side Panel (P3) by tightening with the Phillips Head Screwdriver.
Phillips Head
Screwdriver
4 x Dowels
(H1)
4 x Cam Nuts
(H4)
You will need
Step 4
Phillips Head
Screwdriver
4 x Dowels
(H1)
4 x Cam Nuts
(H4)
Page 6
fantasticfurniture.com.au
(P3)
(P6)
(P6)
(P8)
(P8)
(P8)
(P8)
(P7)
(P7)
(P4)
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
H1
H1
H1
H1
H1
H1H4
H4
Countersink
face bottom
H4
H4
H4
H4

Step 5
Insert 4 x Dowels (H1) into
Left & Right Side Panels
(P3 & P4). Insert 4 x Cam
Nuts (H4) into Left & Right
Side Panel (P3 & P4) as shown.
Rotate the cam nuts so the arrow
points towards the incoming cam bolts.
Attach Top Panel (P1) to Left & Right Side Panel (P3 & P4)
by tightening with the Phillips Head Screwdriver. Attach Top Panel (P1)
to Rail (P7) with 3 x Long Screws (H2). Tightening with the Phillips Head Screwdriver.
With assistance, carefully turn the unit upright.
Slide 1 x Back Panel (P5) into the grooves of Left & Right Side Panel (P3 & P4).
Step 6
You will need
Phillips Head
Screwdriver
4 x Dowels
(H1)
4 x Cam Nuts
(H4)
fantasticfurniture.com.au Page 7
(P5)
(P1)
(P4)
(P4)
(P7)
(P3)
(P3) H2
H2
H2
3 x Long Screws
(H2)
H1
H1
H1
H4
H4
H4
Required
Two People

With assistance, carefully turn the unit upside down.
Slide 1 x Back Panel (P5) into the grooves of Left & Right Side Panels (P3 & P4).
Step 7
Insert 4 x Dowels (H1) into
the Left & Right Side Panel
(P3 & P4). With assistance,
carefully align the Bottom
Panel (P2) to the assembled
frame as shown. Ensure the
Back Panels (P5) slot into the
grooves on the Bottom Panel (P2).
Secure together using 4 x Long Screws (H2), tightening
with a Phillips Head Screwdriver.
Step 8
You will need
Phillips Head
Screwdriver
4 x Dowels
(H1)
4 x Long
Screws (H2)
fantasticfurniture.com.au Page 8
(P2)
(P5)
(P4)
(P4)
(P3)
(P3)
H1
H2
H2
H1
H2
H2
H1
Required
Two People
Required
Two People

You will need
Step 10
Hammer
4 x Plastic
Glides (H17)
fantasticfurniture.com.au
Turn 4 x Legs (P9) clockwise
into the Brackets (H11) until
secure. Hammer 4 x Plastic
Glides (H17) on Legs (P9 x 4)
as shown. With assistance,
carefully turn the unit upright.
Page 9
H17
H17
H17
H17
(P2)
(P9)
(P9)
(P9)
(P9)
(P3)
(P4)
Phillips Head
Screwdriver
You will need
Step 9
4 x Brackets
(H11)
20 x Screws
(H10)
H10
H10
H11
H11
H10
H10
H11
H11
Attach 4 x Brackets (H11) to Bottom Panel (P2) with 20 x Screws (H10) as shown.
Tighten with a Phillips Head Screwdriver.
H10 H10
H11
Required
Two People

Attach Drawer Back (P13) to Left & Right Drawer Side (P11 & P12) and Rail (P15)
with 5 x Long Screws (H2) by tightening with the Phillips Head Screwdriver.
Attach 5 x Cam Bolts (H3) to Drawer Front (P10) by tightening with the Phillips Head
Screwdriver.
15 x Cam Bolts
(H3)
fantasticfurniture.com.au Page 10
You will need
Step 11
Phillips Head
Screwdriver
You will need
Step 12
Phillips Head
Screwdriver
H3H3
H3 H3
H3
15 x Long
Screws (H2)
H2
H2
H2
H2
H2
x3
x3
(P12)
(P15)
(P13)
(P10)
(P11)

Slide Drawer Base (P14) into the grooves of Left & Right Drawer Side (P11 & P12).
Step 13
Insert 5 x Cam Nuts (H4) into
Left & Right Drawer Side (P11 & P12)
as shown. Rotate the cam nuts so the arrows point
towards the incoming cam bolts. Attach Drawer
Front (P10) to Left & Right Drawer Side (P11 & P12). Make sure that the groove lines up
the whole way around the drawer. Tighten with a Phillips Head Screwdriver.
Step 14
You will need
Phillips Head
Screwdriver
15 x Cam Nuts
(H4)
fantasticfurniture.com.au
x3
x3
(P12)
(P12)
(P15)
(P10)
(P11)
(P11)
(P14)
Page 11
H4 H4
H4
H4
H4

H5
H5
H5
H5
H8
H9
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P11) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P12) with 4 x Small Screws (H5) by tightening with the
Phillips Head Screwdriver.
Carefully insert the drawers into the unit by gently guiding the runners into the tracks.
Step 16
(P12)
x3
(P11)
You will need
Step 15
Phillips Head
Screwdriver
12 x Small
Screws (H5)
3 x DL
Runners (H8)
3 x DR
Runners (H9)
fantasticfurniture.com.au Page 12

H12
H13
H16
H15
H14
You will need
Step 17
Phillips Head
Screwdriver
1 x Screw
(H15)
1 x Safety
Strap (H14)
1 x Washer
(H16)
Step 18
You will need
Phillips Head
Screwdriver
1 x Washer
(H16)
Screw and Wall Plug
are not provided.
Please use appropriate
fixtures for your wall.
With assistance, carefully move the unit to its final position. Attach the safety
strap to the wall ensuring it is firmly attached and secure.
Seek advice from a qualified
trades person on how to
attach this safety strap to
your specific wall.
(P5)
(P1)
(P5)
8 x Wedges
(H12)
8 x Wedge
Screws (H13)
We strongly advise
that you use the wall
safety strap provided
to prevent the
unit toppling.
Secure Back Panels (P5 x 2) in place with 8 x Wedges (H12) using 8 x Wedge Screws (H13) by
tightening with the Phillips Head Screwdriver. Use 1 x Screw (H15) and 1 x Washer (H16)
to connect 1 x Safety Strap (H14) on Top Panel (P1).
H16
H15
H14
fantasticfurniture.com.au Page 13
H16
H16
Screw
Wall
Required
Two People

fantasticfurniture.com.au Page 14
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.