fantastic furniture Palermo User manual

Palermo
Buffet 3 Door Walnut

r

2x
Top Panel(P1)
Bottom Panel(P2)
Right Panel(P3)
Left Panel(P4)
Middle Panel(P5)
Long Support(P6)
Short Support(P7)
Long Shelf(P8)
Short Shelf(P9)
2 x Long Back Panels(P10)
Short Back Panel(P11)
Left Door(P12)
2 x Right Door(P13)
4 x Legs(P14)
2 x Support Rails(P15)
Hardware Pack
20 x Cam Bolts
(H1)
20 x Cam Nuts
(H2)
24 x Dowels
(H3)
6 x Hinges
(H4)
48 x Short Screws
(H5)
16 x Washers
(H7) (H8)
12 x Short Bolts 1 x Allen Key
(H9)
4 x Levelling Feet
(H10)
12 x Wedges
(H11)
2 x Long Screws
(H12)
4 x Long Bolts
(H6)
2 x Dowels
(H15)
4 x Washers
(H16)
2 x Wall Straps
(H14)
2 x Felt Pads
(H13)
Legs
(P14)
Legs
(P14)
Legs
(P14) Support Rails
(P15)

16 x Washers
(H7)
12 x Short Bolts
(H8)
1 x Allen Key
(H9)
4 x Levelling Feet
(H10)
H 1 3
H10
H 9
H 8
H 7
4 x Long Bolts
(H6)
H 6
H 7
H 1 3
2 x Felt Pads
(H13)
P 1 5
6 x Cam Bolts
(H1)
6 x Dowels
(H3)
Phillips Head
Screwdriver
(P2)
Insert 6 x Dowels (H3) into Bottom Panel (P2).
Secure 6 x Cam Bolts (H1) into Bottom Panel (P2),
tightening using a Phillips Head Screwdriver.
Stick 2 x Felt Pads (H13) to the centre of Support Rails (P15)
Align and position 4 x Legs (P14) with the pre-drilled holes on the Bottom Panel (P2).
Align and position the 2 x (P15) between the Legs (P14) as shown.
Ensuring the side with the Felt Pads (H13) is on the Bottom Panel(P2)
Using 3 x Washers (H7) and 3 x Short Bolts (H8), secure 1 x Leg (P14) to the Bottom
Panel (P2), tightening using the Allen Key (H9).
Secure the to the Leg (P14) and Bottom Panel (P2) using 1 x
Washer (H7) and 1 x Long Bolt (H6), tightening using the Allen Key(H9).
Repeat this step for the other 3 x Legs (P14).
Support Rails
Support Rails (P15)
P 1 5
P 1 4
P 1 4
P 1 4
P 1 4
H 6
H 7
H 9
H 7
H 8
H 9

Phillips Head
Screwdriver
8 x Dowels
(H3)
8 x Cam Bolts
(H1)
Insert 2 x Dowels(H3) into Right Panel(P3) and secure 2 x Cam Bolts(H1)
to Right Panel(P3) by tightening with a Phillips Head Screwdriver.
Repeat for Left Panel (P4)
Insert 2 x Dowels(H3) into Middle Panel(P5) and secure 2 x Cam Bolts(H1)
to Middle Panel(P5) by tightening with a Phillips Head Screwdriver,
Turn the Middle Panel (P5) over repeat the previous step.
(P3)
(P4)
(P5)
(P5)
Phillips Head
Screwdriver
2 x Cam Nuts
(H2)
Insert 2 x Cam Nuts(H2) into Short Shelf(P9) as shown.Rotate the cam nuts
so the arrows point towards the incoming cam bolts.
Attach Short Shelf(P9) to Right Panel(P3) by tightening the cam nuts(H2)
with the Phillips Head Screwdriver
(P3)

2 x Dowels
(H3)
Insert 2 x Dowels(H3)into Right Panel(P3) and connect Short Support(P7)
to Right Panel(P3).
( )P3
2 x Cam Nuts
(H2)
Phillips Head
Screwdriver
Insert 2 x Dowels(H15) into Middle Panel(P5)
Insert 2 x Cam Nuts(H2) into Short Shelf(P9) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Align the Short Shelf (P9) with the Middle Panel (P5) and Short Support (P7) as
shown. Attach together by tightening the Cam Nuts (H2)
on the Short Shelf (P9) by turning clockwise with the Phillips Head Screwdriver.
2 x Dowels
(H15)
（P7)
(P9)
H15
(P5)

Page 8
7
8
2 x Cam Nuts
(H2)
Phillips Head
Screwdriver
Insert 2 x Cam Nuts(H2) into Long Shelf(P8) as shown. Rotate the cam nuts
so the arrows point towards the incoming cam bolts.
Attach Long Shelf (P8) to Middle Panel (P5) ensuring the groove on the Long
Shelf (P8) is positioned as shown. Secure the panel by
turning the Cam Nuts (H2) clockwise to lock using the Phillips Head Screwdriver.
(P5)
2 x Cam Nuts
(H2)
2 x Dowels
(H3)
Phillips Head
Screwdriver
Connect Long Support(P6) to Middle Panel(P5) using the Dowels
(H15) on the Middle Panel (P5). Insert 2 x Dowels(H3) into Left Panel(P4) .
Insert 2 x Cam Nuts(H2) into Long Shelf(P8) as shown. Rotate the cam nuts
so the arrows point towards the incoming cam bolts.
Align the Left Panel (P4) with the Long Support (P6) and Long Shelf (P8) as shown.
Attach together by tightening the Cam Nuts (H2)
in the Long Shelf (P8) by turning clockwise to lock using the
Phillips Head Screwdriver.
(H2)
(H3) (P6)
(P8)
(P5)

Page 9
9
10
With assistane, carefully turn the assembled frame upright.
Slide 1 x Long Back Panel (P10) through the grooves on the Left Panel (P4)
and Middle Panel (P5) as shown.
6 x Cam Bolts
(H1)
6 x Dowels
(H3)
Insert 6 x Dowels(H3) into Top Panel(P1) and secure 6 x Cam Bolts(H1) into Top Panel(P1)
by tightening with the Phillips Head Screwdriver.
(P1)

Page 10
11
12
Phillips Head
Screwdriver
6 x Cam Nuts
(H2)
Insert 6 x Cam Nuts(H2) into Panel(P3&P4&P5) as shown.Rotate the
cam nuts so the arrows point towards the incoming cam bolts.
With assistance, attach the Top Panel (P1) to the assembled frame (P3, P4, P5)
as shown. Attach together by tightening the Cam Nuts (H2)
on the assembled frame (P3, P4, P5) by turning clockwise using the Phillips
Head Screwdriver.
With assistance, carefully turn the assembled frame over.
Slide the other Long Back Panel (P10) through the grooves on the Middle Panel (P5)
and Left Panel (P4). Slide the Short Back Panel (P11) through the grooves
on the Middle Panel (P5) and Right Panel (P3).
(P11) (P10)