Fermax WAY KIT Instruction Manual

ENGLISH
USER & INSTALLER’S MANUAL
WAY KIT

Parts and Functions
Digital TFT LCD Screen
UNLOCK Button
TALK/MON Button
Microphone
Connection Port
Speaker
Mounting Hook
Mounting Hook
1 2 3
ON
DIPS
L1
L2
ON/OFF Button
Message Indicator
SD card
LCD screen Display the visitors' image
ON/OFF Button Press to open/close screen
Message indicator It will light when the monitor received the unread record
Unlock button Press to release the door
Talk/Mon button Press to communicate hands free with visitor
Press to view the outdoor condition in standby mode
Microphone Receive voice from the user
Mounting hook Use to hang up the monitor
Connection port Bus terminal, Doorbell button terminal, DIP Switches
Speaker Send out vioce from the visitor
Key functions
-1-
DIP Settings
123
ON
Bit
DIP1&2 Reserved. left to default.
Set to OFF. When the monitor is in the middle of the line in daisy chain connection.
Bit State Description
DIP3 123
ON
123
ON Set to ON. When the montior is at the end of the line or connected to a DBC4S.
1. Indoor Monitor
COD. 97767IKg V09_16
.
Door bell
THIS KIT IS NOT COMPATIBLE WITH VERSION V1.0
123
ON
123
ON
123
ON
123
ON
ON
OFF.

-2-
2. Outdoor Station
Camera Lens
Speaker
Nameplate
Call Button
Microphone
Night Light
Rainy Cover
23 mm
90 mm
145 mm
Parts and Functions
Terminal Descriptions
1 2 3
JP/LK
PL
S+ S-
Main Connect Port
BUS
•JP/LK: Lock control jumper, to select the lock type (see 13.2.1 , 13.2.2).
•Main Connect Port: To connect the bus line and the electronic locks.
•BUS: Connect to the bus line, no polarity.
•PL: External lock power input, connect to the power positive (power +).
•S+: Lock power (+) output.
•S-: Lock power (-) output, do not connect in case of using external power supply
for the door lock.
Note: For details related to door openers, see chapters 13.2.1 and 13.2.2.
123

-3-
3.1 Monitor Mounting
145~160 cm
1. Use the screws to fix the Mounting Bracket on the wall, (fitting accesories includes
a Bracket. Two pieces of 4X25 screws are needed for fastening the Mounting
Bracket).
2. Connect the system correctly (see the later connection chapter) then hang the
Monitor into the Mounting Bracket.
3. Mounting
3.2 Outdoor Panel Mounting
The base unit is installed
on the wall.
Connect the cable correctly.
 



Placing name label.
The front cover is installed
onto the base unit. Use the screw to fix the front cover. Installation is complete.
1.Mounting the Rain Cover

-4-
4. Placing Name Label
Remove the plastic cover to open the transparent name label cover, insert a name
label, then put the plastic cover back to the panel.
STEP 1
Unscrew the screws. STEP 2 Replace name label.

-5-
5. Operation Instructions
5.1 Main Menu
Touch the screen anywhere on monitor
in standby mode, the main menu page
will be shown as follows:
5.2 Basic Door Release Operation
1. Press CALL button on outdoor station, the
Monitor rings, at the same time, the screen
displays the visitors' image.
2. Press TALK/MON Button on monitor
or touch icon on screen, you can
communicate hands free with the visitor for
90 seconds. After finishing communication,
press TALK/MON button again or touch icon to end the communication.
If nobody answers the phone, the screen will be turned off automatically after 30
seconds.
1. During talking state, Press UNLOCK Button or touch icon to open the
door for the visitor. The icon release a relay in the bus.
2. When the monitor is in standby mode, press TALK/MON Button or touch
Monitor icon on main menu, the screen can display the view of outside.
3.
4.
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015

-6-
1. Inner Broadcast: If multi slave monitors are installed in the same apartment, select
Inner Broadcast, all the other monitors will mandatory receive broadcast content at
the same time, whichever slave monitor doesn't need to answer the broadcast, and
whichever slave monitor also doesn't need to open the screen.
2. Inner Call: If multi slave monitors are installed in the same apartment, select Inner
Call, all the other Monitors will ring at the same time, whichever Monitor answers
the call, conversation is started and the other monitors will stop ringing at the same
time.
3. Name List Call (External Call): To do an external call to the other apartment in
2 way kits. When selecting this option, apartment 1 can call apartment 2, and
viceversa.
Touch Intercom icon on main menu to get into the intercom mode, you have 3 items
to select: Inner Broadcast, Inner Call and Name List Call (External Call).
6. Intercom Function
Video/Picture Recording
Both Auto-Recording and Manual-Recording are available. And Auto-Recording is
default. If receive a call , after 3s, the monitor will record one video (with SD card)/
picture (without SD card) for each calling automatically. Or you can touch icon to
record the visitor's video/image manually when the monitor is in monitoring or calling.
Note: 1. The video/picture memory function is built into the monitor.
2. SD card must be formatted before use by monitor.
3. SD card is excluded in the kit.
7. Video/Picture Memory
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015
Inner
Broadcast Inner Call Name List Call
Press icon to exit and enter main menu page.

-7-
Video/Picture Playback
Touch Playback icon on main menu, the recorded videos/pictures will be played on
screen, please note that touch icon to Start/Pause the videos recorded.
Note: When the system without SD card: 1. 118 pictures in inner memory
2. Manage each picture
3. Can be transfered to SD card.
When the system with SD card: 1. Up to 32G Micro SD card
2. Video & Audio record
3. Manage each video clips
4. Can be copied
8. Call Record Function
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015
Image: 008/008 2015/02/11 19:23:28
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015
Call Record: All the calls concerning the montior, including Door-station-to-monitor call,
monitor-to-monitor call, will be recored and can be reviewed afterwards.
Touch Call Record icon on main menu to get into the call record mode.When there
are unread call records, arrow color red. Press the unread call record, and then touch
icon to play it.
Call Record 02/11
06-12 11:06 Rafa Nadal
05-27 21:43 Yaga Seelan
04-20 13:33 Yaga Seelan
02-11 15:22 Rafa Nadal
02-117 20:54 Yaga Seelan
Call Record 02/11
06-12 11:06 Rafa Nadal
05-27 21:43 Yaga Seelan
04-20 13:33 Yaga Seelan
02-11 15:22 Rafa Nadal
02-117 20:54 Yaga Seelan
Note:
When there are several call records, the new
ones delete automatically the oldest ones, so
it is not necessary to delete them manually.

-8-
9. Do Not Disturb Function
Touch Do Not Disturb icon on main menu to get into the don't disturb mode, you
have 4 item to select: Normal, for 1 Hour, for 8 Hours and Always. You can select the
appropriate item according to your needs.
Note: When you select "for 1 Hour" or "for 8 Hours", bottom of the screen will display
the remaining time.
10.1 Sounds Settings
Touch icon on main menu page, then select "Sounds" item to enter the sounds
settings page. You can set a variety of ring tones on this page, (touch icon to exit the
setting and return main menu page).
10. Basic Setup Instructions
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015
Do not Disturb
for 8 Hours
Normal
for 1 Hour
Always
Time Remaining: 00:58:32
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015 Monitor Intercom
Playback
Call Record Do not
Disturb Close
Ring Tune
Intercom Bell Door 1 Alert
19 TelRing
Volume
Day
Night
19 15 12 10
06
04
Note:
Volume is related to the volume of the ringtone in
the monitor.
Day: ringtone volume from 6:00 to 18:00 hours.
Night: remaining hours.

-9-
10.2 Date & Time Settings
Touch icon on main menu page, then select "Date & Time" item to enter the date &
time settings page.You can set the date & time on this page, (touch icon to exit the
setting and return main menu page).
Note: Synchronization function is not available
in this version.
10.3 Language Settings
Touch icon on main menu page, then select "Language" item to enter the language
settings page.You can set the language on this page, (touch icon to exit the setting
and return main menu page).
Note: There are 16 different languages available
in the monitor: English, Finnish, Hebrew,
German, Arabic, Hungarian, Czech, Polish,
Nederlands, Norwegian, French, Hindi, Turkish,
Spanish, Italian and Portuguese.
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015 Monitor Intercom
Playback
Call Record Do not
Disturb Close
Date&Time
2015 1102 15 28 10
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015 Monitor Intercom
Playback
Call Record Do not
Disturb Close
Language
English
Finnish
Hebrew
German
Arabic
Hungarian

Door Station Rename
DS-1
Monitor Time Set
30 sec
10.4 Monitor (Rename the outdoor panel & the Monitor Time Settings)
Touch icon on main menu page, then select "Monitor" item to enter the rename &
monitor time settings page.You can set door station rename and "Auto-on" duration (time)
on this page, (touch icon to exit the setting and return main menu page).
-10-
Note: If you want to rename, please touch the place of name, then it will turn keypad
page, you can input your new name in this page.
During monitoring or talking state, touch icon, the Adjust page will be displayed.
1. The Scene mode selection: Total 4 screen
modes can be selected in sequence:
Normal,
Brightly, Soft
and
User. When color, bright
and contrast is modified, the scene will change
automatically the scene mode at User.
2. Note that all the modifications will be performed immediately after the operation.
Touch the window of image to exit the adjust page.
10.5 Screen and Volume Adjustment
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015 Monitor Intercom
Playback
Call Record Do not
Disturb Close
Door Station Rename
DS-1
Monitor Time Set
30 sec
DOOR1 RENAME
DS-1 abc
Normal
5
Brightly Soft User
6
5
7

-11-
The restore to default function allows the user to recover the settings to factory setting.
Note that the restore to default operation will not change any setting.
Enter main menu page and touch icon, then select "About" item to enter the about
settings page, touch icon, the default settings will be loaded.
touch icon to enter the Memo Information page, touch and icon to copy the
pictures to SD card. Touch and icon to format SD card and restart.
11. Restore to Default (About)
Monitor Intercom Playback
Call Record Do not
Disturb Close
06:32 PM
Wed.
02/11/2015 Monitor Intercom
Playback
Call Record Do not
Disturb Close
About
Local Address 00.00
Video Standard
System Version
Display Driver
Font
UI
AUTO
00.02.09
1.3
1.0
1.0
Memo Information
SD Card -
Video Capacity
Video Usage
Flash
Image Capacity
Image Usage
-
-
0118
0024
Copy Pictures To SD ?
Memo Information
SD Card -
Video Capacity
Video Usage
Flash
Image Capacity
Image Usage
-
-
0118
0024
Format SD Card And Restart ?
!Copy Pictures To SD?
Format SD Card And Restart?
!

1. Touch icon on main menu
page, then select "About" item.
2. Touch UNLOCK button
and hold for 2s.
12.1 How to enter the installation setting page
12. Monitor Parameter Setting
-12-
Monitor Intercom Playback
Call Record Do not
Disturb Close
About
Local Address 00.00
Video Standard
System Version
Display Driver
Font
UI
AUTO
00.02.09
1.3
1.0
1.0
INSTALLER SETUP 123
The system offers two methods of date and time.
The code number of 8008 is used to set the date format as month/date/year.
The code number of 8009 is used to set the date format as date/month/year.
The code number of 8012 is used to set the time format as 12 hour system.
The code number of 8013 is used to set the time format as 24 hour system.
12.2 How to set date and time format
The unlock time can be changed by yourself at any time.it can be set from 1 to 99
seconds.
The code number from 8401 to 8499 are used to set the unlock time to 1~ 99 seconds.
Unlock time:
12.3 How to set the unlock parameter
Door-lock type:
3. Access to a new screen that has a keypad to
introduce the wished data. In following chapters
the available and possile settings will be
explained.
There are two working modes:
1. Door opener of Normal working: Unblocking mode = 0 (by default). The door remains
open while the door opener is supplied.
2. Door opener of Inverted working: Unblocking mode = 1.
The door remains open while the door opener is not supplied.
Introducing the number 8010 the unblocking mode 0 is established.
Introducing the number 8011 the unblocking mode 1 is established.

-13-
13. System Wiring and Connections
BUS(IM) BUS(DS)
PC6
AC~
-
+
L1 L2 PL S+ S-
Doorbell Button
Switch
1 2 3
ON
DIPS
13.1.1 One Way Connection
13.1.2 Two Ways Connection
BUS(IM) BUS(DS)
PC6
AC~
-
+
L1 L2 PL S+ S-
Doorbell Button
Switch
1 2 3
ON
DIPS
Doorbell Button
Switch
1 2 3
ON
DIPS
BUS (M)
Monitor BUS (DS) Panel
BUS (M)
Monitor BUS (DS) Panel
Lock
Lock

-14
13.2.2 Door Lock Controlled with potential free relay
Note:
1. Use an external power supply (PSU)
according tothe electrical lock's
consumption.
2. The jumper must be taken off before
connecting.
3. Setup the Unlock Mode of the
Monitor for different lock types.
•Normal open realay type:
Unlock Mode = 0 (by default).
•Normal closed relay type:
Unlock Mode = 1.
LOCK
Take off the Jumper
POWER
SUPPLY
BUS PL S+S-
13.2 Electric Lock Connection
Note:
1. Electronic lock fail secure type
should be used.
2. The door lock is limited to
12Vdc, and holding current must
be less than 250mA.
3. The door lock control is not timed
from the Exit Button (EB).
4. The Unlock Mode Parameter
of Monitor must be set to 0 (by
default). See chapter 12.3.
5. When connect in Electronic lock,
put the jumper in position in 1-2.
EB
*LOCK
PL S+S-
connect Electronic lock, the jumper position in 2-3.
BUS
1 2 3
13.2.1 Door Lock Controlled with Internal Power
Exit
Button
123
123
EB
*LOCK
PL S+S-
connect Electronic lock, the jumper position in 2-3.
BUS
1 2 3
relay
Exit
Button
An intermediate relay should be
connected for equal or higher
voltagesof20V, otherwise the panel
will be damaged.
123
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
1-2.
Forinstallationswitha motorizeddoor,please
follow this method of connection.

14. Setup
-15-
14.1 Unlock Time Setting
backlight indicator
beep + beep
Power up within 5 seconds,
press and hold the "B"
button for 3 seconds, this
will enter the setting menu.
Within 5 seconds, press and hold the
"A" button for 3 seconds, this will
enter the lock time settings.
(blinking)
backlight indicator
Press and hold the "B" button for the
time required. The length of the press
will equal the door release time (range
1~99s).
(off) beep
Note:1. There are two ways to set the unlock time:
a) From monitor: explained in section 12.3 of the manual.
b) From doorpanel: explained in section 14.1 of the manual.
2. During timing, the backlight indicator blinking once per second, tone beeps
once per second. Less than one second by one second calculation.
backlight indicator
(blinking once per second) beep once per second
AA
B
Note: For 1 way doorstation, open front
cover to find button B.

-16-
14.2 Call confirmation
backlight indicator
beep + beep
Power up and within 5
seconds, press and hold the
"B" button for 3 seconds,
this will enter the setting
menu.
Within 5 seconds, press and hold the
"B" button for 3 seconds, this will
enter the ringtone settings.
(blinking)
backlight indicator
(off) beep
Press the "B" button once, this will
select ringtone one, press the "B"
button again to select continuous
and a third time for silent.
beep
(one ringtone: blinking once)
(continuous ringtone: blinking twice)
(silent: blinking three times)
beep,beep
backlight indicator
Note: The ringback tone will circulate at one ringtone continuous ringtone silent.
beep,beep,beep

-17-
15. Cables Requirements
The maximum distance of the wiring is limited. Using different cables will affect the
maximum distance which the system can reach.
Cable Usage A B
Twisted cable 2x0.75 mm260 60
Twisted cable 2x1 mm280 80
B
A
BUS(IM) BUS(DS)
PC6
AC~
monitor
monitor

-18-
●Power supply: 26Vdc +/- 2
●Power consumption: Standby 12mA; Working 350mA (for monitor);
●Standby 33mA; Working status 110mA (for door station).
●Monitor screen: 7 Inch digital color LCD
●Display Resolutions: 800*3(R, G, B) x 480 pixels
●Video signal: 1Vp-p, 75Ω, CCIR standard
●Wiring: 2 wires, non-polarity
●Lock Power supply: 12Vdc, 250mA (Internal Power);
●Unlocking time: 1~99s (Default 3s);
●Working temperature: -15ºC ~ 55ºC;
●Dimension for monitor: 131(H)×225(W)×18(D)mm
●Dimension for door station: 145(H)×90(W)×23(D)mm (Without rain cover).
1) All components should be protected from violence vibration. And not allow to be
impacted, knocked and dropped.
2) Please do the cleanness with soft cotton cloth, please do not use the organic
impregnant or chemical clean agent. If necessary, please use a little pure water or
dilute soap water to clean the dust.
3) Image distortion may occur if the video monitor is mounted too close to magnetic field
e. g. Microwaves, TV, computer etc.
4) Please keep away the monitor from wet, high temperature, dust, caustic and oxidation
gas in order to avoid any unpredictable damage.
5) Must use the right adaptor which is supplied by the manufacturer or approved by the
manufacturer.
6) Pay attention to the high voltage inside the products, please refer service only to a
trained and qualified professional.
16. Specification
17. Precautions

Technical document published for information purposes by FERMAX ELECTRÓNICA.
FERMAX, in a policy of ongoing improvement, reserves the right to modify the contents
of this document and the feature of the products referred to herein at any time and with
no prior notice.
Any such modifications shall be reflected in subsequent editions of this document.
18. Batteries (Important notice)
This equipment contains a lithium button cell CR1120 3V 40mAH welded
to the circuit. This button cell must be removed by a qualified professional
and taken to the proper disposal site.