Fermax FVI-7008 KIT User manual

-1-
FVI-7004 KIT & FVI-7008 KIT
2 WIRE INTERCOM SYSTEM
Please read this manual carefully before using the product you purchase, and keep it well for future use.We reserve the right to
modify the specication in this manual at any time without notice.
FVI-7013 FVI-7014 FVI-7018
RF CARD RF CARD
Quick Guide

-1-
1. Product Lists Of Kits
FVI-7004 KIT consists of：
1*Outdoor Station- FVI-7014；
1*Surface Box- FVI-7000；
4*Indoor Unit- FVI-7013；
1*4 Branch Controller- FVI-6011DBC4A；
1*Power Supply- FVI-6017PC6；
1*Power cable；
4*Proximity Cards；
2*Management Cards- Add Card & Delete Card.
FVI-7008 KIT consists of：
1*Outdoor Station- FVI-7018；
1*Surface Box- FVI-7000；
8*Indoor Unit- FVI-7013;
2*4 Branch Controller- FVI-6011DBC4A;
1*Power Supply- FVI-6017PC6;
1*Power cable;
8*Proximity Cards;
2*Management Cards- Add Card & Delete Card.

-2-
2. System Connection
1 pcs FVI-7014 with 4 pcs FVI-7013
BUS JP/LK
1
2
3
DOOR STATION
1 2 3 4 5 6
DEBUGDS Code
ON
OFF
EB-
EB+
N.O.
LK+
LK-
+12
S/D RC LT
PC6A
LN LPG
CN2
6A
BUS(DS)BUS(IM)
SW
DBC4A
4A
BUS BUS
1 2 3 4
OUT
ON
OFF
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
FVI-6017PC6
Room Code = 01
M/S = Master-0
Room Code = 02
M/S = Master-0
Room Code = 03
M/S = Master-0
Room Code = 04
M/S = Master-0
Work Mode = 0
DS-Code = 0
RF CARD
RFCARD
FVI-7014
FVI-7013 FVI-7013 FVI-7013 FVI-7013

-3-
1 pcs FVI-7018 with 8 pcs FVI-7013
BUS JP/LK
1
2
3
DOOR STATION
1 2 3 4 5 6
DEBUGDS Code
ON
OFF
EB-
EB+
N.O.
LK+
LK-
+12
S/D RC LT
PC6A
LN LPG
CN2
6A
BUS(DS)BUS(IM)
SW
DBC4A
4A
BUS BUS
1 2 3 4
OUT
ON
OFF
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
FVI-6017PC6
Room Code = 01
M/S = Master-0
Room Code = 02
M/S = Master-0
Room Code = 03
M/S = Master-0
Room Code = 04
M/S = Master-0
Work Mode = 0
DS-Code = 0
SW
DBC4A
4A
BUS BUS
1 2 3 4
OUT
ON
OFF
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
BUS
1
Indoor Monitor
2 3 4 5 6
EXTEND
SW+
SW-
EXT-RING
GND
Room Code = 05
M/S = Master-0
Room Code = 06
M/S = Master-0
Room Code = 07
M/S = Master-0
Room Code = 08
M/S = Master-0
FVI-7013 FVI-7013 FVI-7013 FVI-7013
FVI-7013 FVI-7013 FVI-7013 FVI-7013
FVI-7018
RF CARD
RFCARD

-4-
3. Parts and Functions
LCD Screen
Microphone
Speaker
Talk/Mon Button
Unlock Button
Call Button/
Unlock 2nd Button
Setup Button
Down/Decrease Button
Up/Increase Button
1 2 3 4 5 6
ON DIP
SW+
L2L1
SW-
RING
GND
Connection Port
Mounting Hook
Mounting Hook
Microphone Receive voice from the user.
LCD screen Display the visitors' image.
Setup button Press to select the setting item you want.
Down/Decrease
button Press to decrease the value.
Up/Increase button Press to increase the value.
Speaker Send out vioce from the visitor.
Talk/Mon button Press to communicate hands free with visitor;
Press to view the outdoor condition in standby mode.
Unlock button Press to release the door
Call button/Unlock
2nd button
In standby mode, pick up handset, then press Call button to
activate the inner call;
During calling/talking state, press Unlock 2nd button to
release the second door.
Mounting hook Use to hang up the monitor.
Connection port Bus terminal.
Key functions

-5-
L1 L2
12 3 4 5 6
ON DIP
308 mm
123 mm
RF CARD
Camera Lens
Speaker
Night View LED
ID Card Window
Status Indicator
Microphone
Nameplate
LED Indicator
Call button
Mounting box for
flush mounted
Rainy cover for
surface mounted
Connection
port
A B
Note:Key A and key B will not be seen on the panel,they are cryptic.About activating key A and
key B, please refer to Part 5.
4. Terminal Description For Outdoor Station
• +12V: 12VDC power output.
• LK-: Power ground.
• LK+: Common contact of the relay.
• NO.: Normally open contact of the relay
• EB+: Exit button positive connection port.
• EB-: Exit button negative connection port.
• JP-LK: For electronic lock safety type setting(refer to door lock connections).
• SET :DIPswitchesforsystemcongurations.
• CN/KMB: Call button module connection port.
• CN/T-COIL: Reserved.
• CN/FUN: Touch sensor keypad module or TFT display module connection
port.
• CN/WGN: Card reader module connection port.
• Bus(L1,L2): Non-polarity bus line,connect to FVI-6017PC6(power comb unit).
CN-LK
JP-LK
+12V LK- LK+ NO EB- EB+
SET
12V
TX1
RX1
GND
RX3
TX3
GND
5CL
GND
5DA
RST
INT
GND 12V CLK DAT STR C2 C1 CTR GND GND VIO POW
WG0 WG1
GND
12V
CN/KMB CN/T-COIL
CN/FUN CN/WGN
L1 L2
1 2 3 4 5 6
ON DIP

-6-
ON(1)
=
OFF(0)
=
ON
ON
ON
123456
Bit denition Bit state Function Descriptions
Bit-1 and Bit-2
(door station ID setting)
1 2 3 4 5 6
ON
Default setting, ID = 0, setting for the rst door station
1 2 3 4 5 6
ON
ID = 1, setting for the second door station
1 2 3 4 5 6
ON
ID = 2, setting for the third door station
1 2 3 4 5 6
ON
ID = 3, setting for the fourth door station
Bit-3
(single or double row
button setting)
1 2 34 5 6
ON
Default setting ,set "OFF " when using a double row button door
station
1 2 34 5 6
ON
Set "ON" when using a single row button door station
Bit-4
(button code select)
12345 6
ON
Default setting, set "OFF " when using the default codes of the
button
12345 6
ON
Set " ON " when using the programmed codes of the button.
Bit-5
(unlock time quick setting)
1 2 3 4 56
ON
Default setting, unlocking time = 5 seconds.
1 2 3 4 56
ON
Unlocking time = 10 seconds.(can be changed by door station or
software)
Bit-6
(cryptic key setting)
1 2 3 4 5 6
ON
Default setting, normally key A and key B is not useful(about the
position of key A and key B,please refer to part 2)
1 2 3 4 5 6
ON
Activating the key A and key B is allowed.
Totally 6 bits can be congured by dip-switch. All
switches can be modified either before or after
installation, please restarting the power whenever
the switches have been modied.
5. DIP Switches Settings Of Outdoor Station

-7-
6. Indoor Unit Parameter Setting
1.Press About button on
main menu page.
2.Press and hold
UNLOCK button for 3s.
3.Use / button to
increase / decrease the
value; use button to
select next digital.
How to enter the installation setting page
00.00
00.01.00
AUTO
Exit
[0000 ]
? Exit + - Next
When you want to set the monitor parameter, you must to know the setting code.
How to know the machine code
Press ?button on this page.
[0000 ]
? Exit + - Next
Use / button to search
the code you want.
2412: Initial
3006-3600: Monitor Time Set
8000-8003: Local Addrees
Exit Last Next

-8-
DIP Switches Settings Of Indoor Unit
•
•When multi Monitors are installed in one apartment, these Monitors have to use the same
User Code setting, and the Master/Slave mode should be set on the Monitor.
•
ON(1)
=
OFF(0)
=
ON
ON
ON 123456
Bit state User Code Bit state User Code Bit state User Code
1 2 3 4 5 6
ON
Code=1
1 2 3 4 5 6
ON
Code=12
1 2 3 4 5 6
ON
Code=23
1 2 3 4 5 6
ON
Code=2
1 2 3 4 5 6
ON
Code=13
1 2 3 4 5 6
ON
Code=24
1 2 3 4 5 6
ON
Code=3
1 2 3 4 5 6
ON
Code=14
1 2 3 4 5 6
ON
Code=25
1 2 3 4 5 6
ON
Code=4
1 2 3 4 5 6
ON
Code=15
1 2 3 4 5 6
ON
Code=26
1 2 3 4 5 6
ON
Code=5
1 2 3 4 5 6
ON
Code=16
1 2 3 4 5 6
ON
Code=27
1 2 3 4 5 6
ON
Code=6
1 2 3 4 5 6
ON
Code=17
1 2 3 4 5 6
ON
Code=28
1 2 3 4 5 6
ON
Code=7
1 2 3 4 5 6
ON
Code=18
1 2 3 4 5 6
ON
Code=29
1 2 3 4 5 6
ON
Code=8
1 2 3 4 5 6
ON
Code=19
1 2 3 4 5 6
ON
Code=30
1 2 3 4 5 6
ON
Code=9
1 2 3 4 5 6
ON
Code=20
1 2 3 4 5 6
ON
Code=31
1 2 3 4 5 6
ON
Code=10
1 2 3 4 5 6
ON
Code=21
1 2 3 4 5 6
ON
Code=32
1 2 3 4 5 6
ON
Code=11
1 2 3 4 5 6
ON
Code=22
Bit-6 line terminal setting:
Bit state Setting Bit state Setting
1 2 3 4 5 6
ON
Monitor not at
the end of the
line.
1 2 3 4 5 6
ON
Monitor at
the end of
the line.
In the DT system,every apartment must have a unique identification called User Code.
The DIP swiches are used to configure the User Code for each Monitor.
Bit-1 to Bit-5 are used to User Code setting. The value is from 1 to 32, which have 32
different codes for 32 apartments.
Bit-6 is line terminal switch, which have to be set to ON if the Monitor is in the end of the
line(bus), otherwise set to OFF. The end of the line is terminal that no other section will
start from it.

-9-
In the case of double row buttons:
• DIP3 switch set to off
1 2 34 5 6
ON
RF CARD
01 02
03 04
05 06
07 08
RF CARD
02
04
06
08
In the case of single row buttons:
• DIP3 switch set to off
1 2 34 5 6
ON
RF CARD
01
02
03
04
• DIP3 switch set to on
1 2 34 5 6
ON
7. Call codes
The door station automatically assigns the call codes to the connected module’s buttons.
Regardless of the structure of the call button module, the button numbers are listed from
the top to bottom and from left to right (in the case of double row buttons):