Festo NEBC-M12G5-ES LE5-CO Series User manual

Translation of the original instructions
CANopen®, DeviceNet® are registered trademarks of the respective trademark
owners in certain countries.
1 Further applicable documents
All available documents for the product èwww.festo.com/pk.
2 Safety
2.1 Safety instructions
– Do not connect or disconnect plug connector when powered.
– Before starting mounting work: Switch off power supply.
– Observe tightening torques.
2.2 Intended use
Connecting cable with connection technology M12x1, A-coded to EN61076-2-101
for CANopen and DeviceNet.
3 Configuration
3.1 Product design
1Socket (1x)
2Wire end (5x)
3Cable (1x)
Fig. 1
3.2 Pin allocation
Port1Pin Wire colour1) Function
1 – Screening
2 RD V+
3 BK V–
4 WH CAN_H
5 BU CAN_L
1) Colour code in accordance with IEC 60757:1983-01
Tab. 1 Pin allocation
4 Mounting
4.1 Mounting, field device side
1. Connect socket1 to the matching plug connector.
2. Tighten the screw-type lock of the socket1.
4.2 Mounting, controller side
1. Shorten and pre-assemble wire ends as needed.
2. Connect the wires in accordance with the pin allocation.
4.3 Installation
Mounting in energy chain
1. Lay the chain out lengthwise.
2. Place the cables in the chain, making sure they are not twisted.
3. Separate cables from each other using separators/drill holes.
4. Do not connect cables together.
Fig. 2
5. Maintain spaceX. X>10% of the cable diameterD.
If the chain is suspended vertically, increase the spaceX.
Fig. 3
6. Align chain in the operating position:
– Make sure that the radius is greater than the bending radius R of the
cables.
– Cables can move freely in the bending radiusKR of the energy chain.
ÄCables are not forced through the chain.
7. Mount chain (ècorresponding assembly instructions).
8. Fasten cables:
– At both ends of the chain in case of short energy chains (è Fig.4).
– Only at the driver end in the case of long, sliding energy chains (è Fig.5).
Fig. 4
Fig. 5
9. Do not bend cables all the way to the fastening point.
ÄMounting spaceA between the fastening point and bending movement is
observed.
NOTICE!
Damage to cables if the chain breaks.
• Replace cables after a chain break.
NOTICE!
Malfunction and material damage due to vertically suspended cables.
The cables stretch.
• Regularly check the length of the cables.
• Readjust the cables if required.
5 Technical data
NEBC-M12G5-ES-...-LE5-CO
Cable characteristic Suitable for energy chains
Cable composition [mm²] (2x0.34) + (2x0.25) + 0.34
Shielding Shielded
Cable diameter D [mm] 6.7
8081599
Connecting line
NEBC-M12G5-ES-...-LE5-CO
8081599
2017-11
[8081601]
Instructions| Assembly
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
[phone]
www.festo.com

NEBC-M12G5-ES-...-LE5-CO
Current rating at 40°C [A] 4
Surge resistance [kV] 2
Degree of protection IP65, IP67
Note on degree of protection In assembled state
Operating voltage range
DC UB[V] 0…30
Bending radius
Fixed cable installation R [mm] ³35
Flexible cable installation R [mm] ³70
Ambient temperature
Fixed cable installation [°C] –25…+80
Flexible cable installation [°C] –20…+80
Material
Cable sheath TPE-U(PUR)
Insulating sheath PE
Note on materials Cable sheath contains phosphate
esters. Must not be laid in direct
contact with polyurethane-based
pneumatic tubing.
Electrical connection1
Function Field device side
Connection type Socket
Connection technology M12x1 A-coded in accordance with
EN61076-2-101
Type of mounting Screw-type lock
Tightening torque [Nm] 0.4±10%
Electrical connection2
Function Controller side
Connection type Cable
Connection technology Open end
Wire ends Cable unsheathed, wire ends cut off
bluntly
Tab. 2 Technical data