Festo NEBS-M12G5-ES LE5 Series User manual

Translation of the original instructions
1 Applicable documents
All available documents for the product èwww.festo.com/pk.
Document Product Contents
Instructions Sensor e.g. SKDA-...-AB, SBS... Operating
Instructions Servo Press Kit YJKP Assembly, Installa-
tion
Tab. 1
2 Safety
2.1 Safety instructions
– Do not connect or disconnect plug connector when powered.
– Only assemble the product on components that are in a condition to be safely
operated.
– Assembly and installation should only be carried out by qualified personnel.
These personnel have electrical training or a relevant qualification.
2.2 Intended use
Connecting a sensor with the controller.
Sensors: e.g. image processing sensorsSBS..., sensorSKDA-...-AB of the Servo
Press Kit YJKP.
3 Configuration
3.1 Product design
1Socket M12x1, 5-pin
2Wire end (5x)
3Cable
4Screw-type lock
5Braided screen
Fig. 1 NEBS-M12G5-_-LE5
3.2 Contact assignment
Field device side Controller side
1Socket Pin 2Wire ends1)
1 BN
2 WH
3 BU
4 BK
5 GY
Braided screen
1) Colour code in accordance with IEC60757:1983-01
Tab. 2 Contact assignment
4 Mounting
4.1 Assembly, field device side
1. Align socket1 to match plug.
2. Connect socket1 to the plug.
3. Tighten the screw-type lock of the socket1. Tightening torque:
0.3Nm±67%
4.2 Assembly, controller side
1. Shorten and pre-assemble cable sheath and wire ends as needed.
2. Connect the wires in accordance with the contact assignment.
3. Connect braided screen5 across a large area with low-resistance contact to
ground potential.
4.3 Mounting in energy chain
1. Lay the chain out lengthwise.
2. Place the cables in the chain, making sure they are not twisted.
3. Separate cables from each other using separators/drill holes.
4. Do not connect cables together.
Fig. 2
5. Maintain spaceX. X>10% of the cable diameterD.
If the chain is suspended vertically: increase the spaceX.
Fig. 3
6. Align chain in the operating position:
– Make sure that the radius is greater than the bending radius R of the
cables è 5 Technical data.
– Cables can move freely in the bending radiusKR of the energy chain.
ÄCables are not forced through the chain.
7. Mount the energy chain ècorresponding instructions.
8. Fasten cables:
– At both ends of the chain in case of short energy chains
– Only at the driver end in the case of long, sliding energy chains
Fig. 4
9. Do not bend cables all the way to the fastening point.
ÄMounting spaceA between the fastening point and bending movement is
observed.
NOTICE!
Damage to cables if the chain breaks.
• Replace cables after a chain break.
NOTICE!
Malfunction and material damage due to vertically suspended cables.
The cables stretch.
• Regularly check the length of the cables.
• Readjust the cables if required.
8094225
NEBS-M12G5-ES-...-LE5
Connecting cable
8094225
2018-10
[8094227]
Instructions| Assembly
Festo AG & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
[phone]
www.festo.com

5 Technical data
NEBS-M12G5-ES-...-LE5
Cable characteristic Suitable for energy chains
5x0.34Cable composition [mm²]
Shielded
Shielding Yes
Cable diameter D [mm] 5.25
Mounting space A [mm] >105
Current rating at 40°C [A] 4
Surge resistance [kV] 1.5
Operating voltage range
AC UB[V] 0…48
DC UB[V] 0…60
Degree of protection
Degree of protection IP65
IP67
Note on degree of protection In assembled state
Bending radius
Fixed cable installation R [mm] ³26
Flexible cable installation R [mm] ³52
Ambient temperature
Fixed cable installation [°C] –40…+80
Flexible cable installation [°C] –25…+60
Material
Cable sheath TPE-U(PUR)
Insulating sheath PP
Electrical connection1
Function Field device side
Connection type Socket
Connection technology M12x1 A-coded to EN61076-2-101
Type of mounting Screw-type lock
Electrical connection2
Function Controller side
Connection type Cable
Connection technology Open end
Wire ends Cut off bluntly
Tab. 3 Technical data