Festo CPX-E- DI Series Parts list manual

Translation of the original instructions
© 2020 all rights reserved to Festo SE & Co. KG
1 About this document
This document describes the use of the above-mentioned product.
Certain aspects of use are described in other documents and must be observed
è 1.1 Further applicable documents.
1.1 Further applicable documents
All available documents for the product èwww.festo.com/pk.
Document Contents
Description of the automation system CPX-E
(CPX-E-SYS)
Detailed description of the
automation system CPX-E
Instruction manual for automation system CPX-E
(CPX-E-SYS)
Instruction manual and important information on
assembly, electrical installation and mainten-
ance tasks for an automation system CPX-E
Description of digital input module CPX-E-…DI-…
(CPX-E-…DI-…)
Detailed description of product function and
parameterisation options
Documentation of the components in an automa-
tion system CPX-E and the connected peripherals
Information on using the components
Operating conditions| EX Information on the use of the product in poten-
tially explosive gas atmospheres
Documentation for the higher-order controller
and the additional participants in the network
Information on commissioning and paramet-
erisation of the components
Tab. 1 Further applicable documents
1.2 Product version
This document refers to the following product versions:
Product Version
CPX-E-16DI Digital input module CPX-E-16DI, revision1 or later
CPX-E-16DI-EX1E1) Digital input module CPX-E-16DI-EX1E, revision1 or later
1) Use in an industrial environment and in process automation according to NE21 and in potentially explos-
ive atmospheres
Tab. 2 Product version
The product version can be identified from the product labelling or with the help
of appropriate software from Festo.
Appropriate software for determining the product version can be found in the
Festo Support Portal èwww.festo.com/sp.
Information on using the software can be found in the integrated Help function.
There may be an updated version of this document for these or later product ver-
sions èwww.festo.com/sp.
1.3 Product labelling
The product labelling is located on the left-hand side of the module. Scanning the
printed Data Matrix Code with an appropriate device opens the Festo Support
Portal, with the information appropriate for the product. Alternatively, the Product
Key (11-digit alphanumeric code on the product labelling) can be entered in the
search field of the Support Portal.
You can find detailed information on the product labelling in the description of the
module è 1.1 Further applicable documents.
1.4 Specified standards
Version status
EN60529:2013-10 IEC60204-1:2014-10
EN61000-6-2:2005-08 IEC61131-2:2015-05
EN61000-6-4:2007-01 NE21:2012-05
Tab. 3 Standards specified in the document
1.5 UL/CSA Certification
In combination with the UL inspection mark on the product, the information in this
section must also be observed in order to comply with the certification conditions
of Underwriters Laboratories Inc. (UL) for USA and Canada.
UL certification information
Product category code NRAQ/NRAQ7
File number E239998
Considered standards UL 61010-1, 3rd Edition, May 11, 2012, revised April 29, 2016
CAN/CSA-C22.2 No. 61010-1-12, 3rd Edition, revision dated April
29, 2016
UL 61010-2-201, 1st Edition, revised February 20, 2017
CSA-C22.2 No. 61010-2-201: 14, 1st Edition, issue date January
01, 2014
UL mark
Tab. 4 UL/CSA Certification Information
– Technical data and environmental conditions may be subject to change in
order to comply with Underwriters Laboratories Inc. (UL) certification require-
ments for the USA and Canada.
Observe deviations èTechnical data.
– The unit shall be supplied by a power source which fulfils the requirements
on a limited-energy circuit in accordance to IEC/EN/UL/CSA 61010-1 or on a
Limited Power Source (LPS) in accordance to IEC/EN/UL/CSA 60950-1 or
IEC/EN/UL/CSA 62368-1 or a Class 2 circuit in accordance to NEC or CEC.
2 Safety
2.1 Safety instructions
– Take into consideration the legal regulations for the respective destination.
– Use the product only within the defined values
è 13 Technical Dataè Tab. 12 Ambient Conditions UL/CSA.
– Observe labelling on the product.
– Observe further applicable documents.
– Store the product in a cool, dry, UV-protected and corrosion-protected envir-
onment. Ensure that storage times are kept to a minimum.
– Before working on the product: switch off the power supply and secure it
against being switched on again.
– Comply with the handling specifications for electrostatically sensitive devices.
2.2 Intended Use
The product described in this document is intended only for use in an Automation
system CPX-E.
Use the product only as follows:
– Use only in an industrial environment. Outside industrial environments,
e.g.in commercial and residential/mixed-use areas, it may be necessary to
take measures to suppress radio interference.
– Use only in combination with modules and components that are permissible
for the respective product variant èwww.festo.com/catalogue.
– Only use the product if it is in perfect technical condition.
– Only use the product in original status without unauthorised modifications.
Only the conversions or modifications described in this and the further applic-
able documents are permitted.
Additional application ranges for the module CPX-E-…-EX1E:
– Use in process automation
– Use in potentially explosive atmospheres
2.3 Training of Qualified Personnel
Installation, commissioning, maintenance and disassembly should only be con-
ducted by qualified personnel. The qualified personnel must be familiar with
installation of electrical control systems.
3 Further information
– Accessories èwww.festo.com/catalogue.
– Spare parts èwww.festo.com/spareparts.
8126694
CPX-E-…DI-...
Digital input module
8126694
2020-01a
[8126696]
Instructions| Operating
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
[phone]
www.festo.com

4 Service
Contact your regional Festo contact person if you have technical questions
èwww.festo.com.
5 Product overview
5.1 Function
The product supplies digital inputs for recording digital input signals in an Auto-
mation system CPX-E.
5.2 Configuration
5.2.1 Product design
1LED indicators
2Input terminal strips [X0] ... [X7]
3Terminal strip interlock
4Linking element
Fig. 1 Product design
5.2.2 Display components
1Module error [P] (red)
2Status of input 0 … 15 (green)
– input 0 [X0.0]
– input 1 [X0.1]
– input 2 [X1.0]
– …
Fig. 2 LED indicators
5.2.3 Connecting components
Connection [X0]…[X7] Signal
0 Input 0, 2, 4,…
1 Input 1, 3, 5,…
2 +24VDC input 0, 2, 4,…
3 +24VDC input 1, 3, 5,…
4 0VDC input 0, 2, 4,…
5 0VDC input 1, 3, 5,…
Tab. 5 Connection [X0] ... [X7]
6 Transport and storage
• Observe specifications for environmental and storage conditions
è 13 Technical Dataè Tab. 12 Ambient Conditions UL/CSA.
7 Assembly
• Assemble the module as outlined in the “Instruction manual for Automation
system CPX-E” è 1.1 Further applicable documents.
8 Installation
1. Make sure that the power supply is switched off.
2. Connect the lines to the terminal strips in accordance with the "Instruction
manual for the Automation system CPX-E"
è 1.1 Further applicable documents.
9 Commissioning
You can find information on commissioning the automation system CPX-E in the
“Instruction manual for automation system CPX-E”.
You can find information on the parameters in the “Description of
automation system CPX-E” and in the descriptions of the modules used
è 1.1 Further applicable documents.
9.1 Behaviour of the display components after error-free commissioning
Module error [P] (red)1)
Off
1) flashes once briefly during initialisation of the automation system CPX-E.
Tab. 6 Display component after error-free commissioning
You can find information on troubleshooting in the event of incorrect behaviour in
the “Description of Automation system CPX-E” and the descriptions of the mod-
ules used è 1.1 Further applicable documents.
10 Service
NOTICE!
Accumulation of heat due to reduced air supply to electronics.
• Keep the ventilation slots free and regularly remove contamination.
11 Diagnostics and fault clearance
11.1 Diagnostics options
Various options are available for diagnosing errors:
– Internal system diagnostics
– LED indicators on the product
11.2 Internal system diagnostics
The internal system diagnostics is described in the “Description of automation
system CPX-E” è 1.1 Further applicable documents.
11.3 LED indicators
The module-specific LED indicators are described in this document.
The system-specific LED indicators are described in the documentation for the
automation system CPX-E è 1.1 Further applicable documents.
Module error [P]1)
LED
(red)
Meaning Remedy
Lit
Short circuit/overload, sensor supply or
module defective
Eliminate short circuit/overload, check
connected sensors.
Switch power supply UEL/SEN off and on.2)
Off
Normal operating status –
1) flashes once briefly during initialisation of the automation system CPX-E.
2) The requirement to perform this step depends on the setting of the "Behaviour after SCO" parameter
èDescription of digital input module CPX-E-…DI-…
Tab. 7 Module error
Status of input [X0.0], [X0.1], [X1.0], …
LED
(green)
Meaning Remedy
Lit
Input active (logic1)
1 signal at input
–
Off
Input inactive (logic0)
0 signal at input
–
Tab. 8 Status of input [X0.0], [X0.1], [X1.0], …
12 Disposal
ENVIRONMENT!
Send the packaging and product for environmentally sound recycling in accord-
ance with the current regulations èwww.festo.com/sp.

13 Technical Data
General technical data
CPX-E-16DI CPX-E-16DI-EX1E
General technical data
Automation system CPX-E
Description of automation system CPX-E
è 1.1 Further applicable documents
Dimensions
(length × width × height)1)
[mm] 124.3 × 18.9 × 76.6
Product weight2) [g] 102
Mounting position Vertical/horizontal
Ambient temperature [°C] –5…+60 (–5…+50)3)
Storage temperature [°C] –20…+70
Humidity (non-condensing) [%] 0…95
Assigned address space
(inputs/outputs)
[bit] 16/–
Module code (CPX-E-specific) 29 33
Module identification E-16DI E-16DI-EX1E
Degree of protection in accordance with
EN60529
IP20
The degree of protection is not UL-tested.
Protection against electric shock
(Protection against direct and indirect
contact in accordance with IEC60204-1)
through the use of PELV circuits
(protected extra-low voltage)
Electromagnetic compatibility To EN61000-6-2/-4 To EN61000-6-2/-4 and
NE21
1) not including linking element
2) Including linking element
3) for horizontal mounting position
Tab. 9 General Technical Data
Power supply
Operating voltagesupply
UEL/SEN
[VDC] 24±25%
Intrinsic current consumption
at nominal operating voltage
24V from UEL/SEN
[mA] Typ. 15
Tab. 10 Power Supply
Digital inputs1)
CPX-E-16DI CPX-E-16DI-EX1E
Number of inputs 16
Max. cable length [m] 30 Not limited.
Information: note conduct-
or cross-section and
voltage drop for sensor.
Design [VDC] 0…30, positive logic (PNP)
Logic level (logic 0/1) [VDC] £5/³11
Switch-on delay Can be parameterised
Signal extension Can be parameterised
Electrical isolation between
the channels
No
Sensor supply
Sensor power supply [VDC] 24±25%
Voltage drop on short-circuit
protection (reduction of
sensor power supply)
[VDC] £1
Reverse polarity protection
24V USEN against 0V USEN
Yes
Potential difference between 0V external
sensor power supply and 0V internal
sensor power supply
Not permissible
Sensor supply short-circuit protection2)
Short-circuit protection Electronic
Trigger level [A] >1.8
Characteristic Slow-blowing
Behaviour after end of overload Can be parameterised
1) type 3, 24VDC in accordance with IEC61131-2
2) For deviating technical data, see Electrical data UL/CSA and ambient conditions UL/CSA table
Tab. 11 Digital Inputs
Ambient conditions UL/CSA
Pollution degree 3
Installation site for indoor use only
Max. installation height [m] 2000
Tab. 12 Ambient Conditions UL/CSA
Sensor power supply short circuit protection for UL/CSA applications
Short-circuit protection for external implementation:
Resultant current of outputs for 24V USEN
Sensor power supply short circuit protection for UL/CSA applications
Trigger level to be implemented externally with fuses: sensors pro-
tected by fuses individually or collectively for complete
module £1.5A
Tab. 13 Electrical Data UL/CSA