Fiamma F45eagle Setup guide

Awnings
Repair instructions EN
KIT UPGRADE
F45eagle
98655A017

FIAMMASTORE
2
3x
AB
1x
C1x D
1x
PACKAGE CONTENTS
Package contents / Necessary tools p. 2
Installation instructions p. 4
Safety instructions p. 19
Warranty p. 19
A. Fuse holder
B. Plastic rivet
C. Aluminium rivet
D. New winch (grey)

8 mm
ø 3,5 mm
Crank
Handle
FIAMMASTORE
3
Characteristics
Power Supply 12 V
Absorption 12 A
Absorbed power 144 W
Protection fuse T 6,3A L 250V
VIDEO TUTORIAL
hiips://www.fi amma.it/videotutorial/f45
NECESSARY TOOLS

FIAMMASTORE
4
1
2
Check that nothing has been damaged or deformed during shipping.
In the event of doubts or questions concerning the installation, use or limitations of the product, contact the
dealer. We recommend that the installation is carried out by qualified personnel and in compliance with current
local regulations.
WINCH REPLACEMENT
Warning: before starting, when the awning is closed, remove the 12 Volt
power supply
Install fasteners or safety belts, or alternatively, keep the lead bar closed with adhesive tape
(removable). The operation of the winch replacement can be carried out either with closed
awning, but with safety fasteners, or with the awning open. We recommend performing
the repair with the awning closed as it makes, the next operations for centring the winch
easier. If adhesive tape is used, position it so that it adheres well to the aluminium (pulling
the lead bar does not move).

FIAMMASTORE
5
3
3x
1x
Take off the front cover from the Motor Kit removing the plastic rivets (by using a
screwdriver). If the aluminium rivet is in place on the cover, remove it using the drill with the
tip 3.5 mm.
FRONT COVER

8 mm
FIAMMASTORE
6
4
5
Remove the attaching screws from the rear cover.
Take the 8 mm combination wrench and the ratchet wrench with the 8 mm socket and
unscrew the fixing screws securing the engine frame, holding firmly with one hand, the part
that will be removed.
REAR COVER

FIAMMASTORE
7
6
7
Take off the winch assembly (winch + flange). Pull out the planetary gearbox.
Marking the position of the screws with a marker (these marks will be used to mount the
new winch on the ring nut).
WINCHENGINE GROUP RING NUT

FIAMMASTORE
8
8
9
NEW WINCH
COLOUR: GREY
D
Remove the ring nut from the winch (white).
Replace the new winch (grey) on the ring nut, aligning it using the marks previously made
with the marker.
RING NUT

FIAMMASTORE
9
10
11
Before reassembling the group winch, move the engine group close to the planetary
gearbox, to see if there is proper alignment between the gearbox pin and internal compass
on the winch.
Refit the whole winch assembly, while holding the gearbox square and taking care to
ensure the alignment of the pin with the sleeve of the motor kit group.
GEARBOX PIN

FIAMMASTORE
10
12
8 mm
Holding the winch assembly with one hand, tighten the fixing screws securing the motor
unit.

FIAMMASTORE
11
13
CUT THE RED
WIRE
14
A
+
+
INSERTION OF THE SAFETY FUSE
Cut the red wire of the motor.
Cut for about 3-4 mm (1/6 inch) the two ends in rubber of the fuse holder. (The opening of
the hole extends and makes the insertion of the cables).

FIAMMASTORE
12
15
A
16
Insert the wires in the fuse holder.
Insert the spring.

FIAMMASTORE
13
17
A
18 19
Stripping the two ends of the wires and connect them with the screw in the dial (A).
Insert the fuse -
fuse T 6.3A L 250V - (don’t use different fuse)
Close the fuse
holder.

FIAMMASTORE
14
21
20
REPLACEMENT OF THE LEAD BAR CAP
Remove the adhesive tape.
Open the lead bar with the crank handle and close it to verify the microswitch operation.
Next, open the lead bar by 50 cm (20 inches).
20 ”

FIAMMASTORE
15
22
3x
1x
C
B
Reassemble the covers of the motor kit, installing the new lower screw, the new rivets and the
aluminium rivet (if you are unable to put the front cap, open the lead bar by a few centimetres or
3/4 open inch).

FIAMMASTORE
16
23
24
25
Control
System
RETRACT
EXTEND
26
RETRACT
EXTEND
ETRACT
ND
DON’T
PRESS
Remove all the tools and any material left on the vehicle roof.
Restore the 12 Volt power supply.
CONTROL AND GENERAL VERIFICATION OF THE FUNCTIONING
Open the awning lead bar by one meter (39 inches) (with the opening button).
Shake the lead bar to operate the motion sensor and verify that the lead bar closes
automatically.
39 ’’

FIAMMASTORE
17
27
STOP!
PUSH
Interrupt the closing of the lead bar by tapping the microswitch: THE LEAD BAR MUST
STOP!

FIAMMASTORE
18
28
RETRACT
EXTEND
PRESS
RETRACT
CLOSE
29
Push the closing button and close the awning.
The restoration operations are concluded.
In case that the movement doesn’t stop, you could indentify why the Microswitch doesn’t work
(because is not connected or defective); in this case the lead bar will finish the operation until the
closing and it will trigger the protection fuse (that will safeguard the electrical system).
While closing of the lead bar automatically, do not insert your hands or objects that can hamper
the movement.
Pay attention even to non – visible objects (F.I. branches above the awning Fabric) that can
hamper the movement even before that the Microswitch takes action; in this case the protection
fuse triggers and safeguard the electrical system.
Once the fuse triggers, it must be replaced with an identical (Fuse T 6.3 A L 250 V). Never use a
different fuse. We recommend that you carry a spare fuse at all time.
In these cases, we always recommend that you contact the Service Centre.

FIAMMASTORE
19
PATENTPENDING
DUALSHOCK-ABSORBER
PATENTPENDING
DUALSHOCK-ABSORBER
S/N : 9000000
F xxxxxx
xxx
AWNING MODEL
CANOPY COLOUR
EN Warranty Fiamma. In case of defects with regards to materials and manufacturing, the customer
is entitled to the warranty in accordance with local laws and regulations of the country in which the
product was purchased.
In case of problems please contact your local dealer indicating the data on the nameplate. Consult our website
for spare parts drawing.
0° C
We remind you that the awning is for sun protection, so please close your awning in case of rain, wind or snow.
100%

fiamma.com
Fiamma S.p.A. - Italy
Via San Rocco, 56
21010 Cardano al Campo (VA)
All rights reserved.
Fiamma S.p.A.
reserves the right to modify at any time,
without notice, prices, materials,
specifications and models or to cease
production of any model.
A1_IS_98691-034_revA