First Alert FA560VKP Assembly instructions

R
K0022-2 8/02
FA560VKP
VOICE KEYPAD
Installation and Setup Guide
GENERAL INFOR ATION
The FA560VKP is an addressable remote keypad designed for
use with First Alert control panels and provides the following
features:
• Backlit Display • Voice Chime
• Programmable Function Keys • Voice Status
• Built-in Sounder • Message Center
Notes:
• When used with the FA148CP/FA168CPS control panels,
address 16 must be assigned to the first keypad. Additional
keypads must be assigned to address 17–23. Refer to Setting
The Keypad Options on next page.
• Keypad keys are continuously backlit for convenience.
• Permanent display backlighting is an option on some
controls (refer to the control panel’s instructions for details).
• Voice Chime should only be enabled when used with control
panels that support the "chime by zone" mode (e.g.,
FA148CP/FA168CPS). This mode must be enabled at the
control panel. Refer to the control panel's installation and
setup guide for information on how to program the chime
mode.
• Use only zone descriptors supported by this keypad. If using
zone descriptors not supported by this keypad, you must
turn voice status and voice chime off. Table 1 is a list of
applicable zone descriptors and index entries. Refer to the
control panel’s installation and setup guide for information
about how to program zone descriptors.
KEYPAD DISPLAYS AND LEDS
The keypad has the following display features:
• 2-Line, 16-Character, Alpha/Numeric Display
• Custom Zone Descriptors
The following table identifies the keypad LEDs and associated
functions:
LED Function
ARMED Lights red when the system is armed in any mode.
READY Lights green when the system is "ready" to be
armed.
MESSAGE Flashes red when message waiting or lights red
(steady) when in record mode.
PROGRA ABLE FUNCTION KEYS
The keypad's programmable function keys [A, B, C] are
normally used for keypad panic functions, but they can be
programmed for other special functions instead. If they are
programmed for other special functions, the associated keypad
key pairs still provide the respective panic alarm (if
programmed). Refer to the control panel’s Installation & Setup
Guide for details.
Function
Keys
Equivalent Key Pairs
A[1] and [✱]
B[✱] and [#]
C[3] and [#]
DNONE
• Function keys must be held down for at least 2
seconds to activate the programmed function.
• If functions other than panics are assigned to
the programmable function keys, programmed
panics must be initiated by pressing the
programmed key pair.
FUNCTION KEY LABELS
A set of adhesive-backed labels with some typical function
symbols (i.e., fire, police, personal emergency, etc.) is provided.
These labels can be placed on or next to the keys to identify
each key's function for the end user (as determined by the
capability and programming of the control panel; refer to the
installation and setup guide for the control panel).
A
B
C
D
6
4
7
BYPASS
9
CHIME
#
3
STAY
5
TEST
8
CODE
0
2
AWAY
1
OFF
MAX
READY
INSTANT
*
RECORD
STATUS
ARMED MESSAGEREADY
PLAY
VOLUME
VOICE FUNCTION
FA560VKP-002-V1
FA560
WIRING AND INSTALLATION
Keypads can be surface mounted using drywall anchors or to a
single- or double-gang electrical box.
1. Remove the case back by pushing in each of the two
"snaps" along the keypad’s bottom edge and pulling the
case apart.
2. Route wiring from the control panel through the
opening in the case back.
3. Mount the case back to a wall or electrical box.
4. Wire directly from the keypad’s terminal block to the
terminal block on the control board. (Refer to the following
Wiring Table.)
FA560VKP Wiring Table
Keypad Control Panel Wire Color
Y
Data Out Yellow
++ Aux. Pwr Red
–– Aux Pwr (GND) Black
G
Data In Green
5. Reattach the keypad to the case back.
6. Remove the clear protective film from the LCD display.

¬.Ql
K0022-2 8/02
When used with the FA148CP/FA168CPS control
panels, address 16 must be assigned to the first
keypad. Additional keypads must be assigned to
address 17–23. Continue with the following.
SETTING THE KEYPAD OPTIONS
The procedures that follow are used to set the keypad address,
voice chime mode, and additional voice keypad mode.
Setting The Keypad Address
The keypad can either be set for an address of 00-30 or for non-
addressable mode (31). The default keypad address is 31. For
valid address settings for your keypad, refer to the control
panel's Installation & Setup Guide.
Note:
• If unable to enter the address mode, power down, power
up, and try again.
• If 10 seconds pass with no key entry, the keypad
automatically exits the address mode. You must power
down, power up, and start the address mode again.
• The keypad will not enter the address mode if the
control panel is in programming mode.
1. Apply power to the keypad.
2. Within 60 seconds of applying power to the keypad, press
and hold down the [1] key and [3] key at the same time for 3
seconds. The current keypad address will be displayed.
3. Press "00".
The current address is cleared.
4. Enter desired keypad address.
5. Press [✱] to save the displayed address and advance to the
Voice Chime prompt. "VOICE CHIME" (alpha keypad) or
"C" (fixed keypad) is displayed along with the selected mode
"1" or "0".
Setting The Voice Chime Mode
1. Press the [1] key to set the Voice Chime mode on or press the
[0] key to set the Voice Chime mode off.
2. Press [✱] key to save and advance to the Additional Keypad
voice keypad mode.
"ADDITIONAL CON" (alpha keypad) or "A" (fixed keypad)
is displayed along with the selected mode "1" or "0".
Note: Setting Voice Chime mode off does not effect the voice
status or alarm annunciation.
Setting The Additional Keypad Mode
The Additional Keypad mode must be set for all voice keypads
being used.
1. Set the voice keypad Additional Keypad mode as follows:
a. On the Primary voice keypad, press [0] to set the
Additional Keypad mode to NO.
b. On any secondary voice keypads, press [1] to set
Additional Keypad mode to YES.
2. Press [✱]to save the mode.
VIEWING THE KEYPAD ADDRESS
Press and hold down the [1] key and [3] key at the same time
for about 3 seconds. The current address is displayed. No key
entry is allowed. Press any key to exit or wait 10 seconds to
exit the viewing mode.
SPECIFICATIONS
Physical: 7-5/16"H x 5-3/8"W x 1-3/8"D
Display: 2 x 16 Alpha-Numeric Super twist LCD (backlit)
Sounder: Speaker
Electrical:
Voltage: +12VDC
Current: 190mA (ARMED LED lit, LCD backlight and
sounder on) reduces to 60mA when panel is
operating in standby mode (backlight off).
TABLE 1. ZONE DESCRIPTORS AND INDEX ENTRIES
ALARM 002 DOOR 057 KITCHEN 105 PATIO 146 UPSTAIRS 207
ATTIC 009 EMERGENCY 067 LAUNDRY 106 POLICE 151 UTILITY 208
BABY 012 EXIT 071 LIBRARY 109 POOL 152 WINDOW 217
BACK 013 FIRE 079 LIVING 113 ROOM 162 YARD 223
BASEMENT 016 FLOOR 080 MAIN 122 SHED 168 ZONE 225
BATHROOM 017 FRONT 085 MASTER 123 SHOP 170 1ST 228
BEDROOM 019 GARAGE 089 MEDICAL 125 SIDE 173 2ND 230
CLOSED 040 GUN 094 MOTION 131 SLIDING 175 3RD 232
DEN 050 HALL 095 OFFICE 136 SMOKE 176
DETECTOR 052 HOUSE 099 OPEN 138 STORAGE 185
DINING 053 INSIDE 101 PANIC 144 SUPERVISED 190
REFER TO THE INSTALLATION INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED FOR
WARRANTY INFORMATION AND LIMITATIONS OF THE ENTIRE ALARM SYSTEM.
R
149 Eileen Way, Syosset, N.Y. 11791
Copyright 2002 PITTWAY CORPORATION