First Alert FA570RF User manual

K14031UGV1 8/06 Rev. B
FA570RF
Keypad/Transceiver
User Guide
KEYPAD DISPLAYS AND LEDS
The FA570RF has the following features:
•Large, 2-line, 32-character alpha-numeric LCD display.
Display backlighting turns on after any key press and
automatically times out after approximately 30 seconds
without a key press. Time out time is dependent on the
setting of the control panel.
•12 Function Keys located behind a decorative door that
swings down to provide access plus four Special Function
Keys (A, B, C, D) are continuously backlit.
•System numerals, imprinted in large type on the keys for
easy identification. System functions appear below the keys
on the keypad.
The following table shows the LEDs and their functions:
LED Function
ARMED
(Red)
Lights when the system is armed in any
mode.
READY
(Green)
Lights when the system is ready to be
armed (no zone faults are present).
FUNCTION KEYS AND LABELS
The function keys are continuously backlit for ease of use.
(Check the User’s Guide that accompanies the control panel for
detailed instructions on the use of these keys.)
Function Keys - The function keys include keys for panic
alarm activation. The panic alarms are activated by pressing
key pairs [1] & [✱], [3] & [#], [✱] & [#].
How these panic keys function and the type of panic alarms
they produce is determined by the control panel’s capability
and programming. (Check with your installer for the
availability and programming of these panic keys.)
SPECIAL FUNCTION KEYS - These are the four keys
located to the left of the numeric keys (see Figure 1). The keys
may be programmed by your installer for panic alarms or other
special functions such as single-button arming. (Check with
your installer to see which options are available with your
system.)
Each of the four Special Function Keys must be held
down for at least two seconds to activate.
A set of adhesive labels with typical panic symbols is provided.
Place the appropriate label in the indented area on each key,
so that you can easily identify each key’s function.
SOUNDER
The built-in speaker has the following functions:
•Produces warning sounds during alarm and trouble
conditions, and also during entry/exit delay periods.
Provides acknowledgment tones when keys are pressed, and
confirmation tones for successful command entries.
FA570RF-003-V0
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
STATUS FUNCTION
PANIC KEY
PAIRS
SPECIAL
FUNCTION
KEYS
ARMED
READY
Figure 1. FA570RF Keypad/Transceiver
(front door removed)
TROUBLESHOOTING
The error messages listed in the following table cause the
keypad to produce a single ding tone. The table describes the
error messages and the corrective actions.
Display Corrective Action
Low Bat (with Zone
No.)
1. Replace the battery in the wireless
transmitter.
2. Replace the transmitter if the wireless
transmitter does not have a replaceable
battery
Open Ckt Contact your Installer.
Check 100 Contact your Installer.

‡K14031UGV1yŠ
K14031UGV1 8/06 Rev. B
Copyright © 2011 Honeywell International Inc.
www.firstalertprofessional.com
2 Corporate Center Drive, Melville, NY 11747
FEDERAL COMMUNICATIONS COMMISSION STATEMENTS
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized
changes or modifications could void the user's authority to operate the equipment.
CLASS B DIGITAL DEVICE STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your
information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's
instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing
device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a
residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
• Consult the dealer or an experienced radio/TV technician for help.
INDUSTRY CANADA CLASS B STATEMENT
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
FCC/IC STATEMENT
This device complies with Part 15 of the FCC Rules, and RSS210 of Industry Canada. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Cet appareil est conforme à la partie 15 des règles de la FCC & de RSS 210 des Industries Canada. Son fonctionnement est soumis aux conditions
suivantes: (1) Cet appareil ne doit pas causer d' interferences nuisibles. (2) Cet appareil doit accepter toute interference reçue y compris les interferences
causant une reception indésirable.