Fisher-Price Look & Play Zebra User manual

D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Look & Play
Look & Play
Zebra
Zebra™
Please keep this instruction sheet for
future reference, as it contains
important information.
Requires three “AAA” batteries (included).
Adult assembly is required
for battery replacement.
Tool required for battery replacement:
Phillips screwdriver (not included).
L
E
A
R
N
I
N
G
P
A
T
T
E
R
N
S
L
E
A
R
N
I
N
G
P
A
T
T
E
R
N
S
™
Product Number: B0327
Instructions

22
Crib Use
Crib Attachment
• Position the toy on the inside of the crib rails
near the mattress.
• Wrap each fastener strap snugly around a
crib rail and secure.

3
• Open the fasteners on the
back of the toy. Locate the
power/volume switch on
the sound and light box.
• The switch has three positions: off ; on with
low volume and on with high volume .
• Close the fasteners on the back of the toy.
• Press the nose for music and lights.
Hint: If your child is not actively playing with this
toy, it turns off automatically (sleep mode).
• Slide the power/volume switch to the off
position when not in use.
Crib Use
Power/Volume
Switch

4
Fold It Up!
For take-along fun, fold up the toy and attach
the fasteners on each side as shown.
• Place the zebra on the floor for tummy-
time play.
• Press the nose for music and lights.
Floor Use
Fisher-Price, Inc., a subsidiary of Mattel, Inc.
East Aurora, NY 14052 U.S.A.
©2002 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in China B0327pr-0920

5
Battery Replacement
Clip
Slots
Sound
and
Light
Box
Battery
Compartment
Door
For best performance, we recommend
replacing the batteries that came
with this toy with three, new alkaline
“AAA” (LR03) batteries.
• Open the fasteners on the back of the toy.
• Remove the sound and light box from the
clips inside the toy.
• Loosen the screw in the battery compart-
ment door with a Phillips screwdriver.
Remove the battery compartment door.
• Remove the batteries and throw them away.
• Insert three “AAA” (LR03) alkaline batteries,
as indicated inside the battery compartment.
Hint: We recommend using alkaline batteries for
longer life.
• Close the battery compartment door and
tighten the screw with a Phillips screwdriver.
Do not over-tighten.
• Fit the tabs on the sound and light box into
the slots in the clips inside the toy.
• Close the fasteners on the toy.
• When sounds, or lights from this toy become
faint or stop, it’s time for an adult to change
the batteries!

6
Battery Tips
1.5V x 3
“AAA” (LR03)
Shown Actual Size
• Do not mix old and new batteries.
• Do not mix different types of batteries:
alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Remove the batteries during long periods
of non-use. Always remove exhausted
batteries from the toy. Battery leakage and
corrosion can damage this toy. Dispose of
batteries safely.
• Do not dispose of batteries in a fire.
The batteries may explode or leak.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to
be recharged.
• Only batteries of the same or equivalent
type as recommended in the “Battery
Replacement” instructions are to be used.
• If removable rechargeable batteries are
used, they are only to be charged under
adult supervision.
• Rechargeable batteries are to be removed
from the toy before they are charged.
• If you use a battery charger, it should be
examined regularly for damage to the cord,
plug, enclosure and other parts. Do not use
a damaged battery charger until it has been
properly repaired.

Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Consult the dealer or an experienced radio/TV
technician for help.
Note: Changes or modifications not expressly
approved by the manufacturer responsible for
compliance could void the user’s authority to
operate the equipment.
FCC Note
(United States Only)
7

Care
• Open the fasteners on the back of the toy
and remove the sound and light box from
the clips inside the toy.
• Place the toy in a pillowcase and machine
wash cold on a gentle cycle. Do not use
bleach. Line dry the toy.
• Fit the tabs on the sound and light box into
the slots in the clips and close the fasteners
on the toy.
• Do not immerse the sound and light box.
8
Questions? We'd like to hear from you!
Call Fisher-Price® Consumer Relations,
toll-free at 1-800-432-KIDS,
8 AM - 6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD
equipment, please call 1-800-382-7470.
Or, write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
Consumer Information
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc.,
6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone [phone].
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag
#870, Richmond, Victoria 3121 Australia. Consumer Advisory Service
1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.