Fisher-Price L7346 User manual

Please keep this instruction sheet
for future reference, as it contains
important information.
Requires four “AA” batteries (included).
Adult assembly is required.
Tool required for battery
replacement: Phillips
screwdriver (not included).
www.fisher-price.com
L7346

2
2 Arches
Quilt
Puppy House
2 Supports
Not Shown:
3 Hanging Toys
4 Links
Parts
Consumer Information

3
For best performance, we recommend that you
replace batteries that came with this toy with four,
new “AA” (LR6) alkaline batteries.
• Locate the battery compartment on the back of the
puppy house.
• Loosen the screws in the battery compartment door
with a Phillips screwdriver. Remove the battery
compartment door.
Hint: You may need to use the tip of the screwdriver to
lift the battery compartment door.
• Insert four “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for
longer life.
• Replace the battery compartment door and tighten the
screws with a Phillips screwdriver. Do not over-tighten.
• When sounds or motions from this toy become faint or
stop, it’s time for an adult to change the batteries!
In exceptional circumstances, batteries may leak fluids
that can cause a chemical burn injury or ruin your
product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of
different types: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods of
non-use. Always remove exhausted batteries from the
product. Dispose of batteries safely. Do not dispose of
this product in a fire. The batteries inside may explode
or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as
recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removable, rechargeable batteries are used, they
are only to be charged under adult supervision.
1.5V x 4
"AA" (LR6)
Battery Safety InformationBattery Replacement
• Protect the environment by not disposing
of this product with household waste
(2002/96/EC). Check your local authority for
recycling advice and facilities (Europe only).
Battery Compartment Door

4
Lay & Play Setup
• “Snap” the arches to the underside of the
puppy house.
• “Snap” the arch assembly into the supports,
as shown.
• Place the quilt, print side up, under the arch.
• Fit two straps on the side of the quilt through the
slots in the support and one strap on the quilt
through a slot in the arch. Make sure that the end of
each strap forms a "T" on the outside of the slot.
• Repeat this procedure to attach the other side of the
quilt to to the support and arch.
• Pull up on the quilt to be sure it is secure to the
supports and arches.
1
1
12
1
3
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. PRINTED IN CHINA
©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. L7346pr-0920

5
CAUTION
Please keep small parts such as the
plastic tab out of children’s reach.
Throw the plastic tab away.
Before Use
Note: A plastic tab was attached to the toy for in-
store demonstration purposes. While the tab may
have already been removed, check the back of
the puppy house to be sure. If the plastic tab is still
attached, pull and remove the tab. Throw the plastic
tab away.
Lay & Play Setup
• While pushing one end of
a link, pull the other end of
the link. Slide the toy loop
onto the link.
• Push a link onto tab on the
puppy house.
1
4
WARNING
To prevent entanglement injury,
never place gym in a crib or playpen.
Never add strings, ties or other
products to the gym.

6
Power/Volume Switch
Slide the switch to on with low volume , on with
high volume or off .
Mode Switch
Short Play
Baby can bat the hanging toys or puppy house
for music, sound effects and a rocking puppy.
Long Play
Choose this mode for longer music and motions.
On/Off
Switch
Mode
Switch
On/Off
Switch
Power/
Volume
Switch
Sit-At Play
Fun Music and Motion
Hints:
• For the youngest babies, we recommend
assembling the links and animal toys as shown
in the main photo on this page. This arrangement
allows baby to reach the hanging toys while lying
underneath the gym.
• For older babies, remove the overhead arch and
attach the links and hanging toys to the soft quilt for
Sit-At Play fun!
• If your child is not actively playing with this toy,
it turns off automatically (sleep mode).

7
Convert from Lay & Play to Sit-At Play
• While pushing the latches toward the unlock
position , lift to remove the puppy house from
the arches.
1
1
• Remove all six straps on the
quilt from the slots in the
supports and arches.
• While pushing the latch
toward the unlock position ,
lift to remove the arch from
the support.
• Repeat this procedure to remove the other arch.
1
2
• Rotate the end of each support so that it forms
a right angle.
1
3
• Position both supports along one edge of the quilt,
as shown.
• Fit the straps on the ends of the quilt through the
slots in the supports. Make sure that the end of each
strap forms a “T” under the support.
• Pull up on the quilt to be sure it is secure to
the supports.
• “Snap” the puppy house onto the supports.
• To convert back to Lay & Play, first remove the puppy
house from the supports. While pushing the latches
toward the unlock position , lift to remove the puppy
house from the supports. Remove the quilt from the
supports and rotate the supports back to the straight
position. Follow the Lay & Play setup instructions.
1
4

8
Quilt
• Remove the quilt from the supports.
• Wash the quilt in cold water on a gentle cycle.
Do not use bleach. Line dry the quilt.
Arches, Supports, Links, Toys and Puppy House
• Wipe the surface with a clean cloth dampened
with a mild soap and water solution.
• Do not immerse the puppy house.
United States Only
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation.If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly
approved by the manufacturer responsible for
compliance could void the user's authority to
operate the equipment.
FCC StatementCare