Fisher-Price Baby Gymtastics H5704 User manual

Play Wall
www.fisher-price.com
™
H5704
Instructions
Please keep this instruction sheet for future reference,
as it contains important information.
Requires three “AA” (LR6) alkaline batteries (not included).
Adult assembly is required.
Tool required for assembly: Phillips screwdriver
(not included).

Parts
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
2 Plain Walls
(Left and Right)
2 Curtain Walls
(Left and Right)
Handle
Dial Panel
Frog Panel
Lights and Sounds Wall
2 Wall Covers
Inflatable Ball 2 Connectors
2 Connector Caps
2 Bases
3 Pull-Up Handles
2
Parts not shown: 4 Toys
#8 x 13/16” Screw - 6
Shown Actual Size
This toy contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION

Battery Installation Battery Safety Information
• Locate the battery compartment on the lights and sounds wall.
• Loosen the screws in the battery compartment door. Remove the
battery compartment door.
• Insert three “AA” (LR6) alkaline batteries, as indicated inside the
battery compartment.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door and tighten the screws.
• When lights or sounds from this toy become faint or stop,
it’s time for an adult to change the batteries!
1.5V x 3
"AA" (LR6)
Shown Actual Size
In exceptional circumstances, batteries may leak fluids that can cause a
chemical burn injury or ruin your product. To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely. Do
not dispose of batteries in a fire. The batteries may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
Battery Compartment Door
3

• Join the curtain walls. • Join the plain walls.
Assembly
1
11 3
• Insert two screws into the plain wall and tighten.
1
2
Curtain Walls
Plain Walls
• Insert two screws into the curtain wall and tighten.
1
4
4

Assembly
• "Snap" the wall cover onto the top of each wall.
•“Snap” the handle into the sounds and lights wall.
1
5
1
6
Sounds and Lights Wall
Plain Wall
Wall Cover
Curtain Wall
Handle
5
Wall Cover
• Fit the dial panel and frog panel to the sounds and lights wall.
Hint: The dial and frog panels are designed to fit to the sounds
and lights wall one way.
1
7
Dial Panel
Frog Panel
1
8
• Turn the assembly around. Insert two screws into the sounds and
lights wall and tighten.

•“Snap” a pull-up handle to each of the walls.
• Squeeze the stem to inflate the ball.
• Fit the ring on the ball into the slot in the plain wall.
One-time assembly is now complete. Please refer to pages 7-10
to build a Zig-Zag or U-shaped Wall.
1
91
10
Assembly
Pull-Up Handles
Plain Wall Slot
Ball Ring
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. PRINTED IN MEXICO
©2005 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. H5704a-0920

Build a Zig-Zag Wall
• Fit a connector into each base.
• Turn the connector so that the grooves in the connector match
the slots in the base.
1
1
1
3
• Slide the plain wall into the groove in the connector, as shown.
• Push the plain wall down to secure in place.
Base
Plain Wall
7
1
2
• Position the bases on a flat surface, as shown.
• With the handle to the right, slide the sounds and lights wall into
the grooves in the connectors, as shown.
• Push the sounds and lights wall down to secure in place.
Sound and Lights Wall
Handle
Connector
Slot
Groove

Build a Zig-Zag Wall
8
1
4
• Slide the curtain wall into the groove in the connector, as shown.
• Push the curtain wall down to secure in place.
Curtain Wall
1
5
• Fit the connector caps to the connectors.
Connector Caps

Convert to a U-Shape Wall
1
2
• Lift to remove the sounds and lights and curtain wall
assembly from the connector.
Main Wall
9
• Remove the connector cap from the plain wall.
• Lift to remove the plain wall from the connector.
• Set the plain wall aside.
1
1
Plain Wall
Connector Cap
• Turn the base, as shown.
• Slide the sounds and lights and curtain assembly back into the
groove in the connector.
• Push the wall assembly down to secure in place.
Wall Assembly
1
3
Base

Convert to a U-Shape Wall
10
1
5
• Fit the connector cap to the connector.
• Slide the plain wall into the groove in the connector.
• Push the plain wall down to secure in place.
1
4
Plain Wall
Connector
Cap

Music, Lights and Lots of Activities!
Wiggle the tubes, spin the dial or move the frog
for fun sounds, music and lights.
Toy
Peek-a-boo curtain
Bat-at ball
Turning dial
Toy
Bouncing frog
Wiggly-jiggly fun
Pull-up handle
Spinners
• Slide the power/volume switch to the desired
position: on with low volume ; on with high
volume ; or Off .
11
Reposition the toys to encourage standing.
Fit a toy into any of the
slots around the play wall.
Power/Volume Switch

• Wipe this toy with a clean cloth dampened with a mild soap
and water solution. Do not immerse this toy.
• This toy has no consumer serviceable parts. Do not take this
toy apart.
• For easy storage, remove the walls from the connectors.
Remove the connectors from the bases.
Storage
Care
For countries outside the United States:
CANADA: Questions? 1-800-432-5437. Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
GREAT BRITAIN: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500302; www.service.mattel.com/uk
AUSTRALIA: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
NEW ZEALAND: 16-18 William Pickering Drive, Albany 1331, Auckland.
ASIA: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City,
Tsimshatsui, HK, China.
Visit us on line at www.service.fisher-price.com.
Call Fisher-Price®Consumer Relations, toll-free at 1-800-432-5437,
8 AM - 6 PM EST Monday through Friday. Hearing-impaired
consumers using TTY/TDD equipment, please call 1-800-382-7470.
Write to us at: Fisher-Price®Consumer Relations, 636 Girard Avenue,
East Aurora, New York 14052.
Consumer Information
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communica-
tions. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
FCC Note (United States Only)
12