Fisher-Price B0323 User manual

D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Model Number: B0323, B3002
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tools needed for assembly: Phillips Screwdriver and Scissors (both not included).
Requires four “D” (LR20) alkaline batteries for swinging and sound operation;
three “AA” (LR6) alkaline batteries for sound ‘n lights tray operation; and
three “AAA” (LR03) alkaline batteries for remote operation (all batteries not included).
Maximum Weight Limit: 24 lbs. (10.9 kg).
IMPORTANT! The maximum weight limit for this product is 24 lbs. If your child weighs
less than 24 lbs., but is really active and appears to be able to climb
out of the swing, immediately discontinue its use.
Quick Response Swing
with Remote Control
B0323 Quick Response Swing 9/24/02 1:03 PM Page 1

Warning and Caution Consumer Information
2
Occasionally a consumer may experience a problem with
one of our products. If this should happen, please call us
toll-free, rather than return this product to the store. Usually,
we can solve the problem over the telephone or send you
replacement parts. Please call Fisher-Price® Consumer
Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST
Monday through Friday. Hearing-impaired consumers using
TTY/TDD equipment, please call 1-800-382-7470.
Or, write to:
Fisher-Price®
Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
• To prevent falls, never use with an
active child who may be able to
climb out of the seat.
• Never leave child unattended.
• To prevent injury or death from
falls or sliding out, always use
restraint system. Never rely on
the tray to restrain child.
WARNING
This product contains small parts
in its unassembled state. Adult
assembly is required.
CAUTION
B0323 Quick Response Swing 9/24/02 1:03 PM Page 2

Parts
3
Front Base
Rear Base
Housing
2 Rear Legs
(Shorter)
Motor Housing
Seat with Restraint
2 Seat Tubes
Bracket
Seat Wire
2 Seat Wire
Caps
2 Accessory Bins
Pad
Remote Control
and Holder
Tray
Toybar
2 Front Legs
(Longer)
M4 Screw - 4
Shown Actual Size
M4 Bolt - 1
Shown Actual Size
#8 x 11/4" Screw - 6
Shown Actual Size
3.5mm x 1.25cm Screw - 4
Shown Actual Size
B0323 Quick Response Swing 9/24/02 1:03 PM Page 3

• Place the front base on a flat surface.
• Position a front leg (longer) so that the tapered end is
downward, as shown.
• While pressing the button on one of the front legs, insert it
into the front base. Push down on the front leg until the
button “snaps” into the hole in the front base.
• Repeat this procedure to assemble the other front leg to
the front base.
Front Base
Tapered End
Tapered End
Front Legs
(Longer)
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
Assembly
• Using scissors, remove the ribbon connecting the remote
and the holder.
4
Press
Button
Press
Button
Remote
Holder
Ribbon
1
• While standing on the front base, pull the front legs up.
The front legs should remain secured to the front base.
If you can remove the front legs, you have not assembled
them correctly to the front base. Reread and repeat
assembly step 1.
Front Legs Pull Up
Pull Up
Front Base
2
3
• Position the holder so that the
open end faces forward, as shown.
• Slide the holder onto the front leg with a hole.
Holder
Front
Leg Hole
4
Shown Actual Size
M4 Lock Nut
Rounded
Side
M4 Lock Nut
(Rounded
Side Out)
Hexagonal Opening
Hint: An M4 lock nut has been assembled to the holder at
the factory. During shipment of this product, it may have fallen
out. Check to be sure there is a lock nut in the hexagonal opening
on the holder. If it has fallen out, fit the lock nut back into the
hexagonal opening. Make sure the rounded side of the lock nut
faces out.
B0323 Quick Response Swing 9/24/02 1:03 PM Page 4

Assembly
5
• Position a rear leg so that the tapered end is upright.
• While pressing the button on the top of the rear leg, insert it
into the housing short tube, as shown. Push the rear leg until
the button “snaps” into the hole in the short tube.
• Repeat this procedure to assemble the other rear leg to the
motor housing short tube.
• Pull the rear legs down to be sure they are secure in the
housings. If you can remove them, you have not assembled
them correctly. Please re-read and repeat this assembly step.
Button
Rear Legs
Motor Housing
Short Tube
• Fit the bottom of the remote into the cupped portion of
the holder.
• Push to “snap” the top of the remote under the holder clips.
Holder
6
• Position the holder so that the hole in the holder aligns with
the hole in the front leg.
• Insert the M4 bolt through the holder, front leg and into the
lock nut.
• Tighten the bolt with a Phillips screwdriver.
Do not over-tighten.
Holder
Front Leg
5
8
Tapered
End
• Position the housing so that the hub is inward.
• While pressing the button on the top of a front leg, insert it
into the housing slot, as shown. Push the front leg until the
button “snaps” into the hole in the housing.
• Repeat this procedure to assemble the motor housing to
the other front leg.
• Pull the front legs down to be sure they are secure in the
housings. If you can remove them, you have not assembled
them correctly. Please re-read and repeat this assembly step.
Press
Buttons
Front
Legs
Motor
Housing
Hole
Housing Hub
Slot
7
Clips
Remote
M4 Bolt - 1
Shown Actual Size
B0323 Quick Response Swing 9/24/02 1:03 PM Page 5

• Place the rear base on a flat surface so that the buttons
face the front base.
• While pressing the buttons on each side of the rear base,
fit the rear legs onto the rear base. Push the rear legs down
until the buttons on the rear base “snap” into the holes
in each rear leg.
Rear Base
Front
Base
Rear
Legs
Assembly
• While standing on the rear base, pull the rear legs up.
They should remain secured to the rear base. If you can
remove the rear legs, you have not assembled them cor-
rectly to the rear base. Reread and repeat assembly step 10.
• Set the frame assembly aside for Assembly step 21.
• Position the seat face down, with
the top of the seat facing you.
• Position a seat tube so that the long
end is upright and toward you and the curved end is toward
the outside edge of the seat.
• Insert the curved end of the seat tube through the holes in
the ridges on the seat back.
• Repeat this procedure to assemble the other seat tube to
the seat.
6
Press
Button Press
Button
Rear Legs
Pull Up
Pull Up
Rear Base
10
11
12
Top of Seat
Seat Tube
Long Ends
Ridges
Curved
End
• Pull both rear legs out until they “snap” into place.
Pull
Rear
Leg
Pull
Rear
Leg
9
B0323 Quick Response Swing 9/24/02 1:03 PM Page 6

• Insert four M4 screws through the
seat tubes, bracket and into the lock nuts.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Assembly
• Rotate the seat tubes down.
• Fit the seat wire through the slot in the bracket as shown.
7
Seat
Tubes
14
Bracket
Bracket Slot
Seat Wire
Seat Tubes
15
16
• Position the bracket so that the tall end is toward the
bottom edge of the seat.
Hint: The M4 lock nuts have been assembled to the bracket at
the factory. During shipment of this product, they may have
fallen out. Check to be sure there is a lock nut in each hexagonal
opening on the bracket. If one (or more) has fallen out, fit the lock
nut into a hexagonal opening in the bracket. Make sure the
rounded side of the lock nut is facing up.
• Fit the grooves on the bracket to the seat tubes, as shown.
Seat
Tubes
Bracket
Grooves
Tall
End
Bottom
Edge of
Seat
13
M4 Screw - 4
Shown Actual Size
Lock Nut
Hexagonal
Opening
Shown Actual Size
M4 Lock Nut
Rounded Side
B0323 Quick Response Swing 9/24/02 1:03 PM Page 7

• While holding the seat wire in place, carefully turn the
seat around so that the front of the seat faces you.
• Position the seat wire cap so that the rounded edge
is upright.
• Fit each end of the seat wire through the hole in each
seat wire cap.
Ends of
Seat Wire
Assembly
• Press to “snap” the seat wire caps into place.
• Turn the seat face down.
• Fit an accessory bin into the groove on each side of the
seat, as shown.
• Insert two #8 x 11/4" screws through each accessory bin and
into the seat.Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
8
Seat Wire
Cap
Seat Wire
Cap
Grooves
Seat
Accessory Bin
Accessory Bin
Seat Wire
Caps
18
19
20
• Lift the seat tubes slightly.
• With the seat wire hanging down, insert the ends of the seat
wire through the slots in the seat, as shown.
Slots
Seat Wire
17
#8 x 1
1/4
” Screw - 4
Shown Actual Size
Seat Wire
Cap Hole
Rounded Edge Up
Seat Wire is
Through Hole in
Seat Wire Cap
“Snap” in Place
B0323 Quick Response Swing 9/24/02 1:03 PM Page 8

Assembly
• Fit the pocket on the back of the pad onto the seat back.
• Fit the waist belts through the smaller slots in the pad.
9
Waist Belts
Pad
Slot
Slot
23
• Lift the bottom of the pad.
• Insert the pad elastic loops through the holes in the
seat bottom.
• Insert the crotch belt through the slot in the pad.
• From under the seat, fit the elastic loops onto the tabs on
the seat bottom.
24
• Insert a #8 x 11/4" screw through each frame hub and into
the swing tubes.Tighten the screws with a Phillips screw-
driver. Do not over-tighten.
• Again, push down on the seat to be sure the seat is secured
to both frame hubs.
Frame
Hubs
22
Pad
Elastic
Loops
Holes
Crotch
Belt
• Position the seat assembly so that the front of the seat is
toward the curved front base.
• While pressing the buttons on the swing tubes, insert them
into the frame hubs. Push the swing tubes up until the
buttons “snap” into the hole in the frame hubs.
• Push down on the seat to be sure the seat is secured in
both frame hubs.
Swing
Tube
Front
of Seat
Curved
Front
Base
Push
Button
Frame Hub
21
Seat Bottom
#8 x 1
1/4
” Screw - 2
Shown Actual Size
B0323 Quick Response Swing 9/24/02 1:03 PM Page 9

Assembly
10
• Fit the bottom edge of the pad around the bottom edge
of the seat.
• Hook the elastic loops on each side of the pad to the peg
on the back of the accessory bins.
25
Elastic
Loop
Elastic
Loop
• Fit the toy bar plugs into the sockets on the swing tubes.
Hint: If the toybar plugs do not fit into the sockets, turn the
toybar around.Now, fit the plugs into the sockets.
• Insert two 3.5mm x 1.25cm screws through each plug and
into each socket. Tighten the screws with a Phillips screw-
driver. Do not overtighten.
26
Plug
Toybar
Plug
Socket
Plug
Hub
3.5mm x 1.25cm Screw - 4
Shown Actual Size
B0323 Quick Response Swing 9/24/02 1:03 PM Page 10