Fisher-Price G5912 User manual

Please read these instructions before assembly and use of this product.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
Requires four LR14 (“C”) alkaline batteries for operation (not included).
Weight Limit: 9 kg (20 lbs).
IMPORTANT! The maximum weight limit for this product is 9 kg (20 lbs).
If your child weighs less than 9 kg (20 lbs), but is really active and appears to
be able to climb out of the swing, immediately discontinue use.
Product features and decorations may vary from picture above.
G5912
IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE.
WARNING
www.fisher-price.com/uk

2
WARNING
Warnings and Caution
This package contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION
To prevent serious injury or death
from falls and being strangled in
the restraint system:
• Always use the restraint system.
• Not recommended for children
who can sit up by themselves
(6 months approximately,
until 9 kg / 20 lbs).
• Never leave child unattended.
• It is dangerous to use this product
on an elevated surface.
Parts
3 Link Toys
Seat Back Tube
Pad
Frame
Lower Swing Arm Assembly
(with Restraint System)
Front Tube
2 Frame Tubes
Shown Actual Size
#6 x 1,9 cm Screws - 4
NOTE: Tighten and loosen all
screws with a Phillips screwdriver.
Do not over-tighten the screws.

3
Assembly
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT
use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts.
• Rotate the upper frame tube until it "snaps" into an upright
position, as shown.
Upper Frame Tube
1
• Position the front tube so that the rubber feet are flat on
the surface.
• While pressing the button on the lower frame tube, insert it
into an end of the front tube. Continue to insert the lower
frame tube into the front tube until you hear a "click".
• While pressing the button on the front tube, insert it into
the end of the lower frame tube. Continue to insert the
front tube into the lower frame tube until you hear
a "click".
Press Button
on Front Tube
Press Button on
Lower Frame Tube
Rubber Feet Down
2
• Pull the front tube to be sure it is secure to each lower
frame tube.
Lower Frame Tubes
Pull Front Tube
3
• While pressing the buttons on the upper frame tubes,
insert them into the holes in the underside of the frame.
• Continue to insert the upper frame tubes into the frame
until you hear a "click" on both sides.
Press Button
on Upper
Frame Tube
Frame
4

4
Assembly
• Check to be sure the upper frame tubes are secure in the
frame. If you can remove the upper frame tubes from the
frame, you have not properly inserted the tubes into the
frame. Remove the upper frame tubes from the frame and
repeat Assembly step 4.
• Fit the lower swing arm assembly to the outer side of the
upper swing arms.
FrameUpper Frame
Tube
Upper Frame
Tube
Lower Swing Arm Assembly
(with Restraint System)
Upper Swing Arms
5
6• Position the seat back tube so that it curves toward the back
of the swing.
• While pressing the buttons on the seat back tube, fit the
seat back tube into the short tubes on the swing arms.
• Push the seat back tube until it “clicks” into place.
• Pull up on the seat back tube to be sure it is secure to the
swing arms.
Seat Back Tube
Buttons
Swing Arm Short Tubes
8
7
• Insert two #6 x 1,9 cm screws through the upper swing arm
and into the lower swing arm. Tighten the screws.

10
5
Assembly
• From behind the seat, insert the waist belts into the slots in
the pad.
• Push to fasten the restraint system to the pad.
Assembly is now complete.
SlotSlot
Waist Belts
Fastener
• Fit the top pocket on the pad over the seat back tube .
• Lift the seat bottom tube and fit the lower pocket on the
pad over the seat bottom tube .
9
Pad Top Pocket
Seat Back Tube
Pad Lower Pocket
Seat Bottom Tube



6
Battery Installation
1.5V x 4
LR14
SHOWN ACTUAL SIZE
Hint: We recommend using alkaline
batteries for longer battery life.
• Locate the battery compartment door on the frame.
• Loosen the screws in the battery compartment door.
• Remove the battery compartment door and the battery
holder from the battery compartment.
• Open the battery holder.
• Insert four LR14 alkaline batteries as indicated inside the
battery holder.
• Close the battery holder.
• Align the ridge on the battery holder with the groove in the
battery compartment.
• Slide the battery holder back into the battery compartment.
• Replace the battery compartment door and tighten
the screws.
Battery Compartment Door
Battery Holder
Battery Compartment Door
Battery Holder
1
2
3
Battery Holder

Battery Safety Information
In exceptional circumstances, batteries may leak fluids
that can cause a chemical burn injury or ruin your product.
To avoid battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Dispose of
batteries safely. Do not dispose of batteries in a fire.
The batteries may explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product
before charging.
• If removeable, rechargeable batteries are used, they are
only to be charged under adult supervision.
Set-Up & Use
WARNING
IMPORTANT! Before each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken.
Contact Mattel for replacement parts and
instructions if needed. Never substitute parts.
7
To prevent serious injury or death
from falls and being strangled in
the restraint system:
• Always use the restraint system.
• Not recommended for children
who can sit up by themselves
(6 months approximately, until
9 kg / 20 lbs).
• Never leave child unattended.
• It is dangerous to use this product
on an elevated surface.

8
Set-Up & Use
• Place your child in the seat. Position the crotch belt between
your child’s legs.
• Fasten the waist belts to the crotch belt. Make sure you
hear a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
Securing Your Child
To tighten the restraint straps:
• Feed the anchored end of the restraint strap up through
the buckle to form a loop . Pull the free end of the restraint
strap .
To loosen the restraint straps:
• Feed the free end of the restraint strap up through the buckle
to form a loop . Enlarge the loop by pulling on the end
of the loop toward the buckle. Pull the anchored end of the
restraint strap to shorten the free end of the restraint strap .
1
2
Waist Belt
Restraint
Waist Belt
Crotch Belt
Loosen
Anchored End
Free End
Tighten
Free End
Anchored End

9
Set-Up & Use
Starting the Swing
• Turn the power dial to any of eight settings.
• Give the seat a light push to start the swinging motion.
Adjust the swing power dial to the desired swing
motion setting.
Hint: As with most battery-powered swings, a heavier child will
reduce the amount of swinging motion on all settings. In most
cases, the low setting works best for a smaller child while the
high setting works best for a larger child.
• If swinging stops while using a lower setting, try a higher
setting. Give the seat a light push to start the swinging
motion again.
• Be sure to turn this product off when not in use.
Turn the power dial to the off setting .
IMPORTANT! Do not lift this product while your child is in it.
Power Dial
Power Dial
• Fit the link toys to either of the hanging toys on the swing.
3 Link Toys

Baby Activated
10
Set-Up & Use
Hint: Your baby can enjoy lights and music with or without swinging.
Parent Activated
• Slide the lights and music switch to:
When baby pulls either toy on the arch, one tune plays along with twinkling lights.
On this setting, six tunes (approximately 10 minutes) play along with dancing lights.
On this setting, music plays for about 10 minutes.
Turns lights and music off.
• Turn the volume dial to a comfortable listening level.
IMPORTANT! Low battery power may cause this product to operate erratically (no sounds/movement) and the product
may not turn off. Remove and throw away all four batteries and replace with four, new LR14 alkaline batteries.
Lights and
Music Switch Volume Dial Lights and
Music Switch