Fisher-Price T1828 User manual

www.fisher-price.co.uk
T1828
WARNING
IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE.

2
IMPORTANT! Please keep this instruction sheet for future reference,
as it contains important information.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required. Tool needed for assembly: Phillips
Screwdriver (not included).
• Requires one "D" (LR20) alkaline battery for soothing unit
operation and two "AA" alkaline batteries for toy bar operation
(batteries not included).
• Product features and decorations may vary from photographs.
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this product on an elevated surface,
since child's movement may cause
the product to slide or tip over.
Use only on a oor.
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion)
since the product can tip over and
cause suffocation in soft surfaces.
• Always use restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20lb).
• Never use toy bar as a handle.
• Never use as a carrier or lift while
child is seated.
WARNING
CAUTION
This package contains small parts in
its unassembled state. Adult assembly
is required.
Consumer Information
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ®and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA T1828pr-0726

3
Pad
Retainer
2 Feet
Left Base Wire
Seat Back Tube
Footrest
Right Base Wire
Base Tube
Retainer
Toy Bar
Parts
IMPORTANT! Please remove all parts from the package and identify
them before assembly. Some parts may be packed in the pad.
Note: Screw shown actual size. Tighten or loosen all screws
with a Phillips screwdriver. Do not over-tighten the screws.
M5 x 20 mm Screw – 4
1
2
• Place the base tube on a flat surface.
• Position the left and right base wires as shown.
• Fit the left base wire and right base wire into the base tube.
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Fisher-Price®
for replacement parts and instructions if needed. Never substitute parts.
Right Base Wire
Base Tube
Left Base Wire
Non-skid Surface
• Position the feet so the non-skid surface is down.
• Fit the feet on the base tube, as shown.
Assembly

4
3
• Insert screw into each foot and tighten.
Assembly
4
• Position the footrest so that the soothing unit is upright.
• Fit the footrest onto the ends of the base wires.
Base Wires
Footrest
5
Seat Back Tube
• Fit the seat back tube onto the ends of the base wire.
• Push the seat back tube to be sure it is completely on the
base wires.
6
• Fit a retainer to the outside of the seat back tube, as shown.
Make sure the socket in the retainer is upright.
• Insert a screw through the hole in the seat back tube, base wire
and into the inside of the retainer.
• Repeat this procedure to assemble the other retainer to the other
side of the seat back tube.
• Pull the seat back tube up to be sure it is secure. If you can
remove either end of the seat back tube, you have not assembled
the retainers correctly. Remove the screws, re-read and repeat
Assembly steps 5 and 6.
Retainer Socket Up

5
• Position the pad above the frame.
• Fit the upper pocket on the back of the pad onto the seat back tube.
Pad Seat Back Pocket
7
Assembly
8
9
Pad Lower Pocket
• Lift the footrest. Fit the lower pocket on the back of the pad onto
the footrest.
Retainers
• Fit the retainers through the side openings in the pad.
• Fit the edges of the soothing unit through the large opening in the
front of the pad.
Soothing Unit
10
Toy Bar Plugs
Sockets
• Insert and “snap” the toy bar plugs into each retainer socket.
Hint: The toy bar is removable. Press the ends of the latches and
lift the toy bar.

6
• Pull to remove the pad from around the retainers and the
soothing unit A.
• Remove the pad bottom pocket from the footrest B.
1
B
A
A
• Loosen the screw in the battery compartment door. Remove the
battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
• Replace the battery compartment door and tighten the screw.
• Pull and fit the pad seat bottom pocket around the soothing unit
and footrest.
• If this product begins to operate erratically, you may need to reset
the electronics. Slide the power switch off and then back on.
2
Battery Installation
Toy Bar
• Loosen the screws in the battery compartment door with a
Phillips screwdriver.
• Insert two "AA" (LR6) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
• If the toy bar begins to operate erratically, you may need to reset
the electronics. Remove the batteries and replace them.
3
Hint: We recommend using an alkaline battery for longer
battery life.
+
–1,5V
“D” (LR20)
1,5V x 2
“AA” (LR6)
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.

7
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this product on an elevated surface,
since child's movement may cause
the product to slide or tip over.
Use only on a oor.
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion)
since the product can tip over and
cause suffocation in soft surfaces.
• Always use restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20lb).
• Never use toy bar as a handle.
• Never use as a carrier or lift while
child is seated.
WARNING
1
2
Setup and Use
• Tighten each waist belt so that the restraint system is snug against
your child. Please refer to the next section for instructions to
tighten the waist belts.
Restraint System
Restraint Belts
Securing Your Infant
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten the restraint belts to the restraint pad. Make sure you hear
a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
Restraint Pad

8
• Make sure your child is properly secured in the seat.
• Slide the power switch to: Vibrations or Off.
IMPORTANT! Low battery power causes this product to operate
erratically: no vibrations and the product may not turn off.
Remove and discard the battery and replace with a new
“D” (LR20) alkaline battery.
• Pull the ring on the toy for music and sounds.
Power Switch
Soothing Unit
3
To tighten the restraint belts:
• Feed the anchored end of the restraint belt up through the buckle
to form a loop A. Pull the free end of the restraint belt B.
To loosen the restraint belts:
• Feed the free end of the restraint belt up through the buckle to
form a loop A. Enlarge the loop by pulling on the end of the loop
toward the buckle. Pull the anchored end of the restraint belt to
shorten the free end of the restraint belt B.
Anchored End Anchored End
TIGHTEN LOOSEN
Free End Free End
Setup and Use
B
C
A
Care
• The pad is machine washable. Wash it separately in cold water on
the gentle cycle. Do not use bleach. Tumble dry separately on low
heat and remove promptly.
• The frame, toy bar and toys may be wiped clean using a mild
cleaning solution and damp cloth. Do not immerse the toy bar.
Do not use bleach. Do not use harsh or abrasive cleaners.
Rinse clean with water to remove residue.
A
To remove the pad:
• Pull to remove the pad from around the retainers and the soothing
unit A.
• Remove the bottom pocket of the pad from the footrest B.
• Lift to remove the pad C.
• To replace the pad, refer to Assembly steps 7 - 9.
Protect the environment by not disposing of this product with
household waste (2002/96/EC). Check your local authority for
recycling advice and facilities (Europe only).