Fisher-Price Action Sounds Trike J6276 User manual

www.fisher-price.com
J6276
Instructions
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Requires three "AA" batteries (included).
Tools needed for assembly: Phillips Screwdriver, Hammer and
Scrap Block of Wood (not included).
Age: 2 - 6 years; Weight Limit: 60 lbs (27 kg).
Product features and decoration
may vary from the photograph.
®

2
IMPORTANT!
• Please save all packaging material until assembly
is complete to ensure that no parts are discarded.
• If you are missing a part, please call toll-free
1-800-432-5437, rather than return this product
to the store.
• Please wipe each part with a clean, dry cloth
before assembly.
• Some parts shown are assembled to both sides
of the trike.
Harley-Davidson and the Harley-Davidson Bar & Shield logo are registered trademarks of H-D Michigan, Inc. used under license.
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. PRINTED IN MEXICO
© 2005 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. J6276pr-0920
This product contains small parts in its
unassembled state. Adult assembly is required.
CAUTION
Parts
Part Not Shown: Label Sheet
Seat
Frame
Pedal
2 Fork Covers
Front Wheel
Pedal Axle
Fork
Headlight
Cover
Seat Retainer
Cap
Straight
Axle
2 Rear Wheels
Handlebar
2 Hubcaps
2 Covers
4 Pedal Hubs
#8 x 3" Screw – 1
#8 x 3/4" Screw – 6
FASTENERS ACTUAL SIZE
Cap Nut – 2

3
Assembly
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
Rear Wheel
(Indented Side Down)
• Turn the frame on its side with the exposed end of the
straight axle up.
• Place the cap nut assembly tool under the assembled rear
wheel and onto the cap nut.
• Slide a rear wheel (indented side up) onto the end of the
straight axle.
• Slide a hubcap (peg side down) onto the straight axle.
• Place a cap nut on the end of the straight axle. Tap the
cap nut with a hammer. Gently pull the rear wheel up
to be sure the cap nut is securely attached to the
straight axle.
• Insert one of the tabs on a cover into a slot in the hubcap.
Push to snap the cover into place. Repeat this procedure to
attach the other cover to the other hubcap.
Cap Nut
Rear Wheel
(Indented Side Up)
Cap Nut
Assembly Tool
Assembled
Rear Wheel
Straight Axle
Hole Hole
Frame
Straight Axle
BOTTOM VIEW
BOTTOM VIEW
Hubcap
(Peg Side Up)
Hubcap
(Peg Side Down)
Frame
Straight Axle
2
3
1Scrap Block
of Wood
Cover
Hubcap
• Fit two pedal hubs onto the pedal axle tabs. Make sure the
tabs fit into the slot in each pedal hub.
Pedal Hub
Pedal Hub
Pedal Axle
Ta b
Ta b
Slot
4

4
Assembly
• While holding the pedal hubs
on the pedal axle, insert the
pedal axle through the hole in
the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
Hole
Pedal Axle
Pedal Hubs
Front Wheel
• Fit a pedal on the pedal axle. Tap the pedal with a hammer
until it is secure.
• Pull the pedal up to be sure it is secure. If you can remove
it, you have not secured it properly. Tap it with the
hammer again.
Pedal Axle
Scrap Block of Wood
Pedal
Pedal Hub
Pedal Hub
• Turn the front wheel
assembly over.
• Insert the remaining pedal
hubs on top of and below the pedal axle and into the hole
in the center of the front wheel.
• Push the pedal hubs into the center of the front wheel until
they are flush with the surface of the front wheel.
5
6
7
• Place the front wheel assembly between the fork arms.
Make sure the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• Insert two #8 x 3/4" screws into the fork cover and tighten.
• Repeat this procedure to attach the other fork cover to the
other fork arm.
Fork Arms
Pedal Axle
Groove
Fork Cover
8

5
Assembly
• Insert the fork post up through the hole in the neck of the
frame. Make sure the fork is positioned so that the fork
covers face the rear wheels.
• Place the handlebar onto the fork post and push it down
onto the frame. Make sure the handlebar is positioned so
that the screw hole faces the rear wheels and aligns with
the screw hole in the fork post.
Hint: You may need to rotate the handlebar to align the holes.
• Insert the #8 x 3" screw through the hole in the handlebar
and into the fork post so that part of the screw (about 3/4") is
still visible. Tighten the screw.
Handlebar
Frame
Neck
Fork
Post
Fork Cover
Rear of Trike
• Position the seat upside down.
• Fit the small pegs on the seat retainer into the holes in
the seat.
• Insert and “snap” the cap into the hole in the frame.
Cap
Seat Retainer
Seat
Peg
Holes
9
10
12
FIRST, Insert the
screw so that 3/4" is
visible. THEN,
tighten the screw.
3/4"
11
• Fit the tab on the headlight cover to the slot in the top of
the handlebar.
• Insert two #8 x 3/4" screws into the headlight cover. Tighten
the screws. Do not over-tighten.
Headlight Cover
Slot