Fisher-Price BUBBLE MOWER H8910 User manual

H8910
Please keep this instruction sheet
for future reference, as it contains
important information.
Adult assembly is required.
No tools needed for assembly.
www.fisher-price.com

• Please make sure your child does not
follow you using this toy while you are
operating a real lawn mower. Your
child should play in a separate area
away from the area where
you mow.
• Use only bubble solution in this toy.
• Make sure your child understands
that bubble solution is not for drinking
and that it should be kept away from
the eyes.
• While filling or cleaning this toy, try
to avoid spilling bubble solution on
the floor. It may create slippery
floor conditions.
• Bubble solution used in this product
may stain or stick to some surfaces.
Water toys sometimes get messy.•
Protect play surfaces before use.
Overfilling of resevoir may cause•
leakage.
• Insert and "snap" the handle into the
mower, as shown.
2
IMPORTANT! Assembly

Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO H8910a-0920
3
Locate the filler cap on the front of•
the mower.
Attach the filler cap to the top of the•
bubble solution bottle.
Then, twist the bubble solution bottle•
to secure the cap.
• Insert the bottle, cap side down,
into the opening near the front of
the mower.
• Press down on the bottle for about
15 seconds to fill the mower.
1
1
1
2
1
3
Bubblin ' Fun
P
R
E
S
S
Note: Before use, remove the cap and
seal from the bubble solution and
throw it away.
Filler Cap
Bubble
Solution
Bottle

• Push the bubble mower so all four
wheels contact the ground.
• Bubbles begin flowing after the
mower has been pushed about
15-20 walking steps. As long as the
mower is being pushed, bubbles
continue to flow.
• When bubbles stop, press down
on the bubble bottle again for 15
seconds to refill.
4
Bubblin ' Fun
Note: We do not recommend the use
of silicones or oily lubricants on this
toy. As with any bubble producing toy,
when even a very small amount of
silicone or oily lubricants are put into
or used near the bubble chambers,
bubbles will not form.

5
• Replace the filler cap on the bubble
solution bottle and place the bottle
in the filler opening cap end up.
Note: Keep the bubble solution bottle
with your toy and refill as needed. Do
not discard the bubble solution bottle.
• Thoroughly rinse the bubble chamber
on the side of the mower and the filler
opening near the front of the mower
with clean water from a garden hose
or faucet.
• Lift to remove the bubble solution
bottle from the mower.
Turn the bubble solution bottle upright
and twist to remove the filler cap.
• Tip the mower forward to empty all
the water.
Cap End Up
For Storage
1
1
1
2
1
3
1
4
Let ' s Clean Up
Rinse Here
Rinse Here

6
Problem Cause Solution
No bubbles Not enough bubble solution in
bubble chamber
Press down on bubble solution
bottle for 15 seconds to refill.
Bubble chamber is clogged
and dirty
Follow instructions in “Let’s
Clean Up” section to clean bubble
chamber thoroughly.
You have not walked far enough
to produce bubbles
The bubble mower needs to be
pushed a minimum of 15-20
walking steps before bubbles
begin to flow.
You are walking too quickly Walk at a slow, steady pace.
The rear wheels do not contact
the ground
Push the mower so that the
rear wheels always contact
the ground.
Silicone or oily lubricants
got into the bubble chamber
Never use silicone or oily
lubricants on this product (the
wheels). Bubbles will not form
if even a very small amount of
these substances get into the
bubble chamber.
Bubble solution is leaking from
the mower
Bubble chamber over-filled Fill only by using the filler cap
which will dispense the correct
amount of solution.
The mower is used on an
inclined surface
Use the mower only on flat,
level ground.
Bubble solution is foaming Bubble chamber is clogged Follow instructions in "Let's
Clean Up" section to clean bubble
chamber thoroughly.
Problems and Solutions
CO
N
S
UMER
ASS
I
S
T
A
N
CE
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.