Fisher-Price Discovery Airport 77831 User manual

Model Number 77831
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tool required for battery installation:
Phillips screwdriver (not included).
Requires four “AA” (LR6) alkaline batteries (not included).
Discovery
Airport
Discovery
Airport
Discovery
Airport™
D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m

2
Parts
For Best Results
•Roll vehicle in a straight line, within 3 feet of the airport terminal.
• Roll the vehicle at least 6 inches.
• Be sure your child plays with the toy in a quiet room (free from
background noise).
•Press firmly when rolling, so you can hear the “clicking” sound. (The click-
ing sound activates the sound effects).
• Roll the vehicle at a constant speed (not too slow or too fast).
• Turn the helicopter propeller at a constant speed (not too slow or too fast),
within three feet of the terminal.
Press
Firmly
Terminal
3 Feet 3 Feet
3 Feet
3 Feet
Roll at least 6
inches

Parts
2
Parts
3
Luggage Trailer
Parts not shown: 3 Figures.
Terminal Base
Terminal
Ramp with
Fuel Pump
Ramp
Bridge
Bridge Base
Straight Track
Radar Dish
Binocular
Viewer
Windsock
Umbrella
Luggage
Helicopter
Luggage Car
Airplane
Taxi
Helicopter Lift

4
Parts
Battery Installation
Battery Tips:
• Do not mix old and new batteries.
• Do not mix different types of batter-
ies: alkaline, standard (carbon-zinc)
or rechargeable (nickel-cadmium).
• Remove the batteries during long
periods of non-use. Always remove
exhausted batteries from the toy.
Battery leakage and corrosion can
damage this toy. Dispose of batter-
ies safely.
• Do not dispose of batteries in a fire.
The batteries may explode or leak.
• Never short circuit the battery
terminals.
• Non-rechargeable batteries are not
to be recharged.
• Only batteries of the same or equiv-
alent type as recommended in the
"Battery Replacement" instructions
are to be used.
• If removable rechargeable batteries
are used, they are only to be
charged under adult supervision.
• Rechargeable batteries are to be
removed from the toy before they
are charged.
• If you use a battery charger, it
should be examined regularly for
damage to the cord, plug, enclosure
and other parts. Do not use a dam-
aged battery charger until it has
been properly repaired.
Shown Actual Size
1.5V x 4
“AA” (LR6)
• Locate the battery compartment
door on the bottom of the
airport base.
• Loosen the screw in the battery
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
• Insert four, "AA" (LR6) alkaline
batteries, as indicated inside the
battery compartment.
• Replace the battery compart-
ment door and tighten the screw
with a Phillips screwdriver.
Do not over-tighten.
• When sounds or lights from
this toy become faint or stop, it’s
time for an adult to change the
batteries!
Hint: We recommend using alkaline
batteries for longer battery life.
Battery
Compartment
Door
Terminal
Base

Assembly
5
1
2
Terminal Base
Terminal
• Position the terminal base on a flat surface. Insert and "snap" the
tabs on the bottom of the terminal into the slots in the terminal
base as shown. Press firmly on the building to make sure all five
tabs have snapped in place.
• Pull up on the terminal to be sure it is secure.
• Place the bridge base on a flat surface. Insert and "snap" the tabs
on the ramp into the slots in the bridge base as shown.
• Insert and "snap" the tabs on the ramp with fuel pump into the
slots in the bridge base as shown.
Bridge Base
Ramp with
fuel pump
Ramp

Assembly
6
3
4
Bridge
• Insert and "snap" the tabs on the ends of the bridge into the
slots in the ramps, as shown.
• Insert and "snap" the tabs on the end of each ramp into the slots
in the straight track as shown.
Ramp Assembly
Straight Track
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2002 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in China 77831a-0920

Assembly
7
5
• Insert and "snap" the peg on the bottom of the radar dish into
one of the two large holes on the roof of the terminal.
• Insert and "snap" the peg on the bottom of the binocular viewer
into the other large hole on the roof of the terminal.
• The windsock can be inserted and removed from any of the
smaller holes on the roof of the terminal.
• The umbrella can be inserted and removed from the hole in the
table on the terminal base.
6
Terminal Base
Groove
• To attach the terminal to the track, place the ridge on the bottom of
terminal base into the groove in the track.
Hint: Lift the terminal base to separate from the track for easier storage.
Table
Binocular
Viewer
Radar Dish
Windsock
Umbrella
Track
Terminal

Label Application
8
Proper label application will help to keep the labels looking their best!
• Wash your hands before applying the labels.
• Make sure the areas where the labels will be applied are clean and dry.
Wipe this product with a clean, soft, dry cloth to remove any dust or oils.
• For best results, do not attempt to apply a label more than once.
• Apply the labels as shown in the illustrations.
Terminal Back View
19
8
14
618
3417
16
17
17
18
2
18
10
11
13
9
15
17
7
12
1
5
18

Airport Fun with Lights and Sound Effects!
Luggage Storage
9
• Locate the power switch on the bottom of the toy.
• Slide the switch to the on position. The lights flash and you’ll
hear a musical "fanfare". The indicator light shows the toy is ready
to recognize the vehicles when rolled.
• If your child does not actively play with this toy for a few minutes,
the toy will play the same fanfare and go to sleep. The indicator
light goes out. Sound effects and lights will not work.
• To "wake up" the toy, press the "X" button on the top of the
airport building.
• When your child is finished playing with the toy, slide the on/off
switch to the off position.
X Button Indicator
Light
Power
Switch
• Place luggage in the groove on the back bumper of the taxi or under
the jet plane.

Roll ‘n Recognize
If Vehicle Sound Effects Are Not Playing
10
Turn the baggage
carousel to hear
a tune.
Hint: Teach your child
how to roll the vehicles at
a consistent speed and in
a straight line to activate
the sound effects.
Rotate the
helicopter
propeller
for lights
and sound
effects.
Raise and lower the
toll gate for flashing
lights and phrases.
Check to see if:
• Vehicles are being rolled or helicopter propeller is being rotated
outside the zone of about three feet from the airport terminal.
• Vehicle is not being rolled at least six inches.
• Your child is playing with the toy in a noisy room with clicking noises
in the background. This toy recognizes the clicking sounds made by
each vehicle. If there is another clicking or tapping noise in the back-
ground, the toy will not be able to identify the vehicle because of the
interference. Make sure your child plays with this toy in a quiet room.
• Your child has rolled more than one vehicle at a time.
• The vehicle is not being rolled smoothly.
• The vehicle is being rolled back and forth (reversing direction).
• Vehicle is not being pressed when rolled, to make it click.
• Your child is rolling a vehicle while the toy is playing a sound effect.
Wait until the sound effect is finished.
Roll any vehicle within 3 feet of the airport. The airport recognizes the
vehicle and responds with a sound effect and lights.