Fisher-Price L3938 User manual

1
Please keep this instruction sheet for future reference,
as it contains important information.
Requires six “AA” (LR6) alkaline batteries (not included).
Adult assembly is required.
Tool required for assembly:
Phillips screwdriver (not included).
www.fisher-price.com
L3938
This product is not recommended for use
on loose dirt or wet surfaces.
TM

2
Parts
This product contains small part,
for assembly by an adult. Take extra
care during unpacking and assembly.
4 Center Tracks
7 Tracks
4 Inside Tracks
2 Ramp Rails (Long) 2 Ramp Rails (Short)
2 Ramps
2 Ramp Bars
2 Ramp Connectors
2 Ramp Spinners
Crash Gate Halves 8 Track Supports
#4 x 3/8" Screw – 12
Shown Actual Size
Note: Tighten and loosen all screws with a Phillips
screwdriver. Do not over-tighten screws.
Parts Not Shown: 2 Cars, Label Sheet
CAUTION
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2007 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA L3938pr-0920

3
• Fit an inside track marked “A” to track marked “A”.
• Insert three screws into the assembly and tighten.
• Repeat this procedure to join two additional “A”
track assemblies.
• Fit an inside track marked “B” to track marked “B”.
• Insert three screws into the assembly and tighten.
• Fit the pegs on the sides of a ramp into the holes in the
long ramp assembly, as shown.
Note: If the ramp does not fit, try the other ramp.
• Repeat this procedure to build the short ramp assembly.
• Set the ramp assemblies aside.
• “Snap” a ramp bar and ramp connector into one side
of a long ramp rail.
• “Snap” the other long ramp rail to the assembly.
• “Snap” the ramp spinner onto the support bar.
1
2
Assembly
• Fit the four center tracks together, as shown.
5
Ramp Bar Ramp
Spinner
Ramp
Connector Long
Ramp Rail
3
A
A
4
B
B

4
6
• Each track piece has a number on the bottom. Simply match the
numbers and fit the pieces together.
Hint: For best performance, we suggest assembling the track on
a hard, flat surface.
Assembly
1
8
9
7
65
4
3
2
Assembly Tip: If you cannot join all the track
pieces together, try fitting together in three
large sections, as shown here.

5
• “Snap” the ramp assemblies to the track.
• “Snap” the crash gate halves to the track.
• Fit the eight track supports on to the matching posts around the track, as shown.
Assembly is now complete.
Assembly
8
Proper label application will help to keep the labels looking their best!
• Make sure the areas where the labels will be applied are clean and dry. Wipe this product with a clean, soft, dry cloth to
remove any dust or oils.
• For best results, do not attempt to apply a label more than once.
• Apply the labels as shown in the illustration above.
7
116
1
1113 4
13
11116
12
5
10
2
2
3
14
11 15
67
8
9
15
11
14

6
• Locate the battery compartment on the bottom of
each car.
• Loosen the screw in the battery compartment door
with a Phillips screwdriver. Remove the battery
compartment door.
• Insert three, new “AA” (LR6) alkaline batteries.
Hint: We recommend using alkaline batteries for longer
battery life.
• Replace the battery compartment door and tighten
the screw.
• When sounds or motions become faint or stop,
it’s time for an adult to change the batteries!
1.5V x 3
"AA" (LR6)
• Protect the environment by not disposing of this
product with household waste (2002/96/EC).
Check your local authority for recycling advice
and facilities.
In exceptional circumstances, batteries may leak fluids
that can cause a chemical burn injury or ruin your toy.
To avoid battery leakage:
• Do not mix old and new batteries or batteries of
different types: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the
battery compartment.
• Remove batteries during long periods of non-use.
Always remove exhausted batteries from the toy.
Dispose of batteries safely. Do not dispose of the
product in a fire. The batteries inside may explode
or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy
before charging.
• If removable, rechargeable batteries are used, they are
only to be charged under adult supervision.
Battery Installation Battery Safety Information

7
Race! Smash! Crash!
• Slide the On/Off switch on the bottom of the car to on.
• Lift the car and shake it to start the "engine" and the
sound effects.
Hint: For maximum distance, shake the car 7 or 8 times.
Shaking more than this does not increase the distance it
will travel.
2
• Set the cars on the starting arrow and press the pedal to start.
• When your car stops, pick it up and shake it. Set it down
again to resume the race.
• Pull the handle down to reset the pedal.
3
• When two cars collide, the doors and hood pop open.
• To reset the car, press down on the hood area.
• Press the button to lower the guardrail and send a car
crashing through the gate!
• When you're finished, slide the On/Off switch to off.
1 4
5

8
United States Only
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference
in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Consult the dealer or an experienced radio/TV
technician for help.
Note: Changes or modifications not expressly approved by
the manufacturer responsible for compliance could void
the user's authority to operate the equipment.
• Wipe with a clean cloth dampened with a mild soap and
water solution. Do not immerse.
FCC Statement
Care
Consumer Information