Fisher-Price Power Wheels B7659 User manual

Please read this manual and save it with your original sales receipt.
Tools needed for assembly: Phillips Screwdriver, Hammer, Pliers
and Safety Scissors (tools not included).
Use only with a Power Wheels®12 Volt Lead-Acid Rechargeable Battery and Power Wheels®
12 Volt Charger with Type “12V” Connector (included).
JEEP and the Jeep grille design are registered trademarks of DaimlerChrysler
Corporation and are used under license. ©DaimlerChrysler Corporation 2003.
Goodyear (and winged foot design) and Wrangler (for tires) are trademarks of
The Goodyear Tire & Rubber Company, used with permission.
Owner's Manual
with Assembly Instructions
For Model B7659
www.powerwheels.com
Product features may vary from the picture above.

2
Table of Contents
Important Information
AImportant Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BWarnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
CParts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
DParts Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
EBattery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
FAssembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
GLabel Decoration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
HBattery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
IBattery Care and Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
JRules for Safe Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
KHow to Operate Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
LCaring for Your Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
MProblems and Solutions Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
NLimited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
•Your new vehicle requires adult assembly. Please set
aside at least 60 minutes for assembly.
•You must charge your battery for 18 - 30 hours
before you use your vehicle for the first time. We
recommend that you start charging your battery before
beginning assembly. Please see Battery Charging
beginning on page 7 for detailed instructions.
•Read this manual carefully for important safety
information and operating instructions before using
your vehicle. Keep these instructions for future
reference as they contain important information.
•This vehicle is designed for use on: grass, asphalt or
other hard surfaces; on generally level terrain; by children
3 years of age and up.
•Make sure children know and follow these rules for safe
driving and riding:
-always sit in the seat.
-always wear shoes.
-only two (2) riders at a time.
•Use this vehicle ONLY outdoors. Most interior floor-
ing can be damaged by riding this vehicle indoors.
Fisher-Price®will not be responsible for damage to
the floor if the vehicle is used indoors.
•This vehicle has adjustable play seat belts. Please
note that the adjustable seat belts are designed to be
a play feature only and do not function as protective
safety restraints.
A
•To prevent damaging the motors and gears, teach your
child to stop the vehicle before switching between forward
and reverse. Do not tow anything behind the vehicle or
overload it. Do not exceed the maximum weight capacity
of 130 lb. (59 kg).
•For safety reasons, your vehicle has been pre-set so
that it will only operate at low speed. You must remove
the high speed lock-out screw to allow operation of
the vehicle at high speed. Please see page 22 for
detailed instructions.
•If you have any questions about your Power Wheels®
vehicle, please call our toll-free service lines at
1-800-348-0751 from 8 AM to 6 PM (EST) Monday
through Friday. Trained customer service representatives
are available to take your call in English or French.
Habla Español? Si usted tiene alguna pregunta ó
necesita asistencia llame gratis 1-800-348-0755 para
los Estados Unidos. Tenemos representantes que
hablan español para atender su llamada.
•For your convenience, Power Wheels®maintains an
independently owned and operated Authorized Service
Center Network with more than 400 authorized service
centers nationwide. The authorized service centers will
repair or replace parts under warranty at no extra charge,
and can perform non-warranty repairs for a minimal
charge. To find the authorized service center nearest to
you, visit us on-line at www.powerwheels.com or call
1-800-348-0751.
•If you would like to register your vehicle, please visit us
on-line at www.powerwheels.com.

CAUTION
WARNING
WARNING
•Battery can fall out and injure a child if vehicle tips over. Always use battery clamp.
•PREVENT FIRE
- Never modify the electrical system. Alterations could cause a fire resulting in serious
injury and could also ruin the electrical system.
- Use of the wrong type battery or charger could cause a fire or explosion resulting in
serious injury.
- Use of Power Wheels®components in products other than Power Wheels®vehicles
could cause overheating, fire or explosion.
•The battery must be handled by adults only. The battery is heavy and contains sulfuric
acid (electrolyte). Dropping the battery could result in serious injury.
•Never allow children to charge the battery. Battery charging must be done by adults only.
A child could be injured by the electricity involved in charging the battery.
•Never lift or carry the battery by the wires or connector. This can damage the battery and
possibly cause a fire resulting in serious injury. Lift and carry the battery by the case only.
•Read the safety instructions on the battery.
•Examine the battery, charger and their connectors for excessive wear or damage each time
you charge the battery. If damage or excessive wear is detected, do not use the charger or
the battery until you have replaced the worn or damaged part.
•HOT motors. Handle carefully.
3
•In the unassembled state, this package contains small parts. Adult assembly is required.
•Use the charger in dry locations only.
•Prevent Injuries and Deaths
• Direct Adult Supervision Required
• Keep Children Within Safe Riding Areas.
These areas must be:
- away from swimming pools and other bodies of water to prevent drownings
- generally level to prevent tipovers
- away from steps, driveways, cars, roads and alleys.
RIDING HAZARD
Warnings and Cautions
B
ELECTRICAL HAZARD

4
Parts
C
•If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than
return this product to the store.
•Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no
parts are discarded.
•Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel
to remove any excess lubricant.
Steering
Wheel Cap
Short Seat Belt Strap - 2
Brushguard
Taillight Housing Set
Taillight Lens Set
12 Volt Charger
Long Seat Belt Strap
Lens Guard - 2
Headlight Lens - 2
Battery Clamp Unit
12 Volt Battery
Light Cover – 2
Spacer - 2
Cap

5
Parts
Hood Latch – 2
Key Assembly
#8 x 1" Screw – 7 #10 x 1" Screw – 7
Windshield
Sport Bar
Not Shown: Label Sheet
Steering Column
All Shown Actual Size
Vehicle Body
Dash
Hood
Seat
*For your convenience, an extra .354 cap nut, #8 x 1", #10 x 1/2"and #10 x 1" fasteners are included.
Steering Wheel
#8-32 x 1.625" Screw – 2
Sport Bar
Support - 2
#10 x 1/2" Screw – 8
#8 Lock Nut – 2
.354 Cap Nut – 2
#8 x 4" Screw – 2

6
1Vehicle Body 1
2Steering Column 1
3.354 Cap Nut 2
4Hood Latch 2
512 Volt Battery 1
6Battery Clamp Unit 1
7Key Assembly 1
8Taillight Lens 2
9 Taillight Housing 2
10 #8 x 1" Screw 7
11 Cap 1
12 Dash 1
No. Part Quantity No. Part Quantity No. Part Quantity
Parts Diagram
D
Note: Some parts shown are assembled on both sides of the vehicle.
13 #10 x 1" Screw 7
14 #10 x 1/2" Screw 8
15 #8 x 4" Screw 2
16 Windshield 1
17 Brushguard 1
18 Steering Wheel 1
19 Steering Wheel Cap 1
20 Seat 1
21 Long Seat Belt Strap 1
22 Short Seat Belt Strap 2
23 Headlight Lens 2
24 Lens Guard 2
25 Hood 1
26 Spacer 2
27 Sport Bar 1
28 Sport Bar Support 2
29 Light Cover 2
30 Lock Nut 2
31 #8-32 x 1.625" Screw 2
1
24
3
11
13
13
13
14
13
13
9
28
5
14
31
30
25
17
6
7
29
2
18
16
12
14
3
27
15
15
23
21
26
19
22
20
22
8
4
10
10
10
10

CAUTION
Use the charger in dry locations only.
WARNING
7
About Thermal Fuses
Your Power Wheels®12 volt battery is equipped with a
built-in thermal fuse. The thermal fuse is a self-resetting
safety device which automatically “trips” and shuts down
operation of the vehicle if the vehicle is overloaded or the
driving conditions too severe. Once a fuse has “tripped”,
it will automatically reset itself after approximately
25 seconds and allow the vehicle to resume normal
operations. To avoid repeated automatic shutdowns, do
not overload the vehicle by exceeding the 130 lb. (59 kg).
maximum weight capacity or by towing anything behind
the vehicle. Avoid severe driving conditions, such as
driving up very steep slopes or running into fixed objects,
which can cause the wheels to stop spinning while power
is still being supplied to the motors. Make sure your child
stops the vehicle before switching speeds or direction.
If a thermal fuse in a battery continually trips under
normal driving conditions, please contact your local
Power Wheels®Authorized Service Center. For the
location of the Authorized Service Center nearest to
you, please visit us on-line at www.powerwheels.com
or call 1-800-348-0751.
Important Notes
•Your new battery must be charged for at least 18 hours
before you use it in your vehicle for the first time.
•You do not need to remove the battery from your
vehicle to recharge it.
•The battery must be upright while charging.
•The charger is not a toy.
•Do not short circuit the battery.
•We recommend that you start charging your battery
before beginning assembly of your new vehicle.
•Before charging the battery, examine the battery case
for cracks and other damage which may cause sulfuric
acid (electrolyte) to leak during the charging process.
If damage is detected, do not charge the battery or
use it in your vehicle. Battery acid is very corrosive and
can cause severe damage to surfaces it contacts.
•Do not charge the battery on a surface which could be
damaged by the acid contained inside the battery. Take
precautions to protect the surface on which you charge
your battery.
•Use only a Power Wheels®12 volt charger with type
“12V” connector (120 VAC 60 Hz 28W with an output of
12 VDC 1200mA) to charge your Power Wheels®
rechargeable 12 volt battery.
•If your battery is old and will not accept a charge, do not
leave it in the vehicle. Always remove a dead battery
from the vehicle.
Battery Charging
E
•Battery can fall out and injure a
child if vehicle tips over. Always use
battery clamp.
•PREVENT FIRE
- Never modify the electrical system.
Alterations could cause a fire resulting
in serious injury and could also ruin the
electrical system.
- Use of the wrong type battery or
charger could cause a fire or explosion
resulting in serious injury.
- Use of Power Wheels®components in
products other than Power Wheels®
vehicles could cause overheating,
fire or explosion.
•The battery must be handled by adults
only. The battery is heavy and contains
sulfuric acid (electrolyte). Dropping the
battery could result in serious injury.
•Never allow children to charge the battery.
Battery charging must be done by adults
only. A child could be injured by the
electricity involved in charging the battery.
•Never lift or carry the battery by the wires
or connector. This can damage the battery
and possibly cause a fire resulting in
serious injury. Lift and carry the battery
by the case only.
•Read the safety instructions on
the battery.
•Examine the battery, charger and their
connectors for excessive wear or damage
each time you charge the battery. If
damage or excessive wear is detected, do
not use the charger or the battery until you
have replaced the worn or damaged part.
ELECTRICAL HAZARD

WARNING
8
Children can be harmed by small parts,
sharp edges and sharp points in the
vehicle’s unassembled state, or by electrical
items. Care should be taken in unpacking
and assembly of the vehicle. Children
should not handle parts, including the
battery, or help in assembly of the vehicle.
Battery Charging
•Plug the charger connector into the battery .
•Plug the charger into a standard wall outlet .
Note: If power flow to the wall outlet is controlled by a
switch, make sure the switch is “ON”.
•Before first-time use, charge the battery for at least 18
hours. Never charge the battery longer than 30 hours.
•Recharge the battery for at least 14 hours after each
use of your vehicle. Do not charge the battery longer
than 30 hours.
•Once the battery is charged, pull firmly on the charger
connector to disconnect it from the battery. Unplug the
charger from the wall outlet. The battery is now ready to
be installed in your vehicle. Please see the Battery
Installation section on page 18 for detailed instructions on
installing your battery. If your battery is already installed in
your vehicle, simply re-connect the motor harness
connector to the battery and lower and fasten the hood.
Battery
Charger
Connector
Assembly
F
IMPORTANT! The battery clamp unit must be
assembled to the dash before assembling the dash
to the vehicle body.
Battery
Clamp
Unit
Dash
•Position the dash face down.
•Fit the battery clamp unit into the underside of the
dash so that the clamp fits into the grooves in the dash.
Make sure the battery clamp unit is flush against the
surface of the dash.
Clamp
Grooves
1

9
21
Battery
Compartment
Dash
•Position the dash on the vehicle body.
•Make sure the motor harness connector wire is through
the groove in the dash.
•Insert a #10 x 1/2" screw through each of the two corner
dash tabs nearest to the passenger compartment .
•Insert a #10 x 1" screw through the two dash tabs
nearest to the battery compartment .
•Insert a #10 x 1" screw into the hole in the center of the
dash, near the battery retainer clip .
•Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
Battery Clamp
Assembly
Battery
Clamp Unit
•Insert two #10 x 1" screws through the holes in the
battery clamp unit and into the pegs in the dash.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Motor
Harness
Connector
Wire
2
3
•Before applying the labels, wipe the surface of the
vehicle with a clean, dry cloth to remove any dust or oils.
•Place the labels exactly as shown in the illustrations.
•For best results, avoid repositioning a label once it has
been applied to the vehicle.
13 14 15
4
HI LO KC
21 23
16 Labels - Dash
17
12

10
Dash Key Assembly
•Insert and “snap” the key assembly into the opening in
the dash, as shown.
Dash View
Steering
Column
Hole
Bottom View
•Wipe the steering column with a paper towel to remove
any excess lubricant.
•Turn the vehicle on its side.
•Insert the straight end of the steering column up
through the hole in the vehicle body wall and out
through the hole in the dash.
Assembly
5
6
•Insert the end of the steering column through the hole
in the steering rod.
•Fit a cap nut onto the end of the steering column.
•While supporting the steering column, tap the cap nut
with a hammer to secure it on the steering column.
Hint: You may want the help of another person to
support the steering column while you tap the cap nut
with the hammer.
Steering
Rod
Cap Nut
End of
Steering
Column
Bottom View
7
.354"
.354 Cap Nut

11
•Fit the wide notch in the side of a headlight lens under
the wide tab on a lens guard.
•Press firmly on the inside of the headlight lens to snap it
into the lens guard.
•Repeat this procedure to assemble the other headlight
lens to the remaining lens guard.
Lens
Wide
Notch
Wide Tab
Lens Guard
Assembly
•Fit the lens tabs on the back of a lens assembly into the
headlight slots in the grille.
•Press firmly to snap the lens assembly into the grille.
•Repeat this procedure to snap the other lens assembly
into the grille.
Grille
Ta b
Ta b
Slot
Slot
10
11
Steering Wheel
•Fit the steering wheel cap into the center of the
steering wheel.
•Insert two #8 x 1" screws, as shown.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Steering
Wheel Cap
9
•Turn the vehicle upright.
•Position the steering wheel so that the spokes form a
“Y” as shown. The tab on the steering wheel stem
should face up.
•Fit the steering wheel onto the steering column.
•Fit a cap nut onto the end of the steering column.
•Tap the cap nut with a hammer to secure it on the
steering column.
Hint: You may want the help of another person to
support the steering column while you tap the cap nut
with the hammer.
Steering Wheel
Cap
Nut
Steering
Column
“UP”
Ta b
8
.354"
.354 Cap Nut

12
Assembly
•Position the windshield so that the wipers face the front
end of the vehicle.
•Insert and “snap” the two large tabs on the windshield
into the large slots in the dash.
•Pull up on the windshield to be sure it is secure.
Windshield
Wipers
Large
Ta b Large
Ta b
Large Slots
Hood Tabs
•Position the hood over the front of the vehicle body
as shown.
•Insert the tabs on the hood into the slots in the
vehicle body.
•Close the hood.
Slot Slot
•Insert a hood latch into one of the slots in the vehicle
body, near the hood area.
•Twist the base of the hood latch 1/4turn to secure it in
the vehicle body.
•Repeat this procedure on the other side of the hood
area to attach the other hood latch to the vehicle body.
Hood
Latch
Slot
Hood
Latch
Slot
12
13
14
Brush Guard
Front Bumper
15
•Fit and hold the brush guard against the front bumper.
•Insert two #10 x 1" screws through the front of the brush
guard and into the front bumper.
•Tighten the screws with a Phillips screwdriver. Do not
over-tighten.

13
•Turn the seat upside down.
•Insert the fastener end of a short seat belt strap through
the slot near the outer edge of the seat. Make sure the
side of the seat belt with the fastener faces the outer
edge of the seat.
•Pull the short seat belt strap completely through the slot
until the last T-loop at the opposite end of the belt catches
against the slot. You will pull one T-loop through the slot.
•Repeat this procedure to assemble the other short seat
belt strap.
Short Seat
Belt Strap
Fastener End
Seat
Slot
End
T-Loops
Slot
T-Loop (Pull through slot)
Assembly
•Insert each fastener end of the long seat belt strap
through a slot in the center of the seat. Make sure the
fasteners face the outer edge of the seat.
•Pull each side of the long seat belt strap evenly through
the slots. Make sure to pull each T-loop through a slot.
•Turn the seat upright.
T-Loop
Fastener End
Long Seat Belt Strap
•With the seat at an angle, insert the tabs on the front
edge of the seat into the slots in the foot-well wall .
•Push down firmly on the edge of the seat above each
tab to snap the tabs into the slots .
•Rotate the back of the seat down to snap the seat
back tabs into the slots in the vehicle body. Push down
firmly on the seat back.
Seat
Tabs
Seat Back
Tabs
Slot
1
2PUSH
HERE
17
18
19
Spacers
Brush Guard
Grille
16
•Fit two spacers between the grille and the
back of the brush guard, as shown.
•Insert two #8 x 4" screws through the brush
guard, the spacers and into the holes in
the grille.
•Tighten the screws with a Phillips screwdriver. Do not
over-tighten.

14
•Fit a support to one side of the sport bar.
•Insert a #8- 32 x 1.625"screw through the support, the
sport bar and out through the support.
•Fit a lock nut to the end of the screw.
•While holding the lock nut with the pliers, tighten the
screw with a Phillips screwdriver. Do not over-tighten.
Sport Bar
Supports
Assembly
•Insert a #8 x 1" screw into the rear of seat, as shown.
•Tighten the screw with a Phillips screwdriver. Do not
over-tighten.
20
21
•Fit the light covers to the lights on the sport bar, as shown.
•Insert a #10 x 1/2"screw through the light cover and into
the light. Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Light
Covers
Lights
22
Dash View

•Fit the sport bar into the holes in the vehicle body.
•Push down firmly on a sport bar support while pulling
up on the side fender to fit the sport bar into the
vehicle body.
•Repeat this procedure on the other side of the
vehicle body.
Sport Bar Support
Side
Fender
PULL
HERE
PUSH
HERE
23
15
Assembly
Taillight
Housing
Taillight
Lens
#8 x 1" Screws
•Turn the vehicle upright.
•Using safety scissors, remove the taillight lenses and the
taillight housings from the plastic connectors. Dispose of
the plastic connectors.
•Face the rear of the vehicle.
•Fit a taillight lens inside a taillight housing.
•Position the taillight housing with lens against the vehicle
body with the screw holes aligned, as shown.
•Insert two #8 x 1" screws through the taillight lens and
housing and into the vehicle body as shown.
•Tighten the screws with a Phillips screwdriver. Do not
over-tighten.
•Repeat this procedure to attach the other taillight.
•Position the cap so that its tether points down.
•Snap the cap into the hole under the right taillight.
Cap
Tether
•Turn the vehicle on its side.
•Insert two #10 x 1/2"screws into the holes in the
underside of each rear wheel well, through the vehicle
body and into the ends of the sport bar.
•Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Rear of
Vehicle
24
25
26
Bottom View

16
Label Decoration
G
Proper label application will help to keep the labels looking their best! When applying labels, keep the following
guidelines in mind:
•Wash your hands before applying the labels.
•Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils.
•Place the labels exactly as shown in the illustrations.
•For best results, avoid repositioning a label once it has been applied to the vehicle.
•After applying a label, rub the label firmly with a clean, dry cloth to make sure the label is adhered to your
vehicle. Start at the center of a label, and smooth towards the outer edges to remove air bubbles.
1
Inside Dash View
2
®
Back View
8
9
22
18 20
28
26
19
10

17
Label Decoration
Left Side View
25
2
6
5
1
3
4
3
10
11
11
24
7
29
29
29
29
30
30
30
30
Right Side View 4
27
27

18
Battery Installation
H
IMPORTANT! Use only a Power Wheels®12 volt battery.
Use of any other battery will damage your vehicle. Make
sure that you charge the battery for at least 18 hours using
the enclosed Power Wheels®12 volt charger before
operating your vehicle for the first time. Charge the battery
for at least 14 hours after each use of the vehicle. Never
charge the battery longer than 30 hours. Failure to follow
these instructions may damage your battery and will void
your warranty. It is easier to install the battery before
assembling the hood to your vehicle. If you have already
assembled the hood to your vehicle, you may want to
remove it to install the battery.
Pb
Hood
Battery
Compartment
•Lift the hood to access the battery compartment.
Pb
Battery
Compartment
Battery
Compartment
Battery
Battery
Clamp
Locator
Ribs
•Press the battery clamp to slide it into the dash .
•While holding the battery clamp against the dash, place
the battery in the battery compartment . Make sure the
battery is upright and postioned between the locator ribs
at the bottom of the battery compartment.
Battery
Clamp
•Release the battery clamp. Make sure the battery clamp
slides over the top of the battery. If the battery clamp
does not slide over the top of the battery, reposition the
battery in the battery compartment. (See step 2.)
Pb
Battery
Motor
Harness
Connector
•Plug the motor harness connector into the battery. Push
firmly to make sure the connectors are completely joined.
Hint: To remove a battery from the battery compartment,
disconnect the motor harness connector from the battery.
Press and hold the battery clamp against the dash and lift
the battery from the battery compartment.
Hood
Hood Latches
•Lower the hood and secure the hood latches.
1
2
3
4
5

19
Battery Care and Disposal
I
If a battery leak develops, avoid contact with the leaking
acid and place the damaged battery in a plastic bag. Please
refer to the information on this page for proper disposal.
If acid comes in contact with skin or eyes, flush with cool
water for at least 15 minutes and call a physician.
If acid is internally ingested, give water, milk of magnesia
or egg whites immediately. Never give emetics or induce
vomiting. Call a physician.
•Charge a new battery for at least 18 hours before first
use. Never charge the battery longer than 30 hours.
Overcharging or undercharging the battery may shorten
battery life and decrease vehicle running time.
•After the first charge, recharge the battery for at least
14 hours after each use. Never charge the battery longer
than 30 hours. Charge the battery after each use,
regardless of how long the vehicle was used.
•The battery must be upright while charging.
•Do not allow the battery to run down completely
before charging.
•Charge the battery before storing the vehicle.
•Charge the battery at least once per month, even if the
vehicle has not been used.
•Leaving the battery in a discharged condition will
ruin it.
•Do not store the battery in temperatures above 75° F
or below -10° F.
•Use only a Power Wheels®12 volt battery. Remember
to charge the new battery at least 18 hours before first
time use.
•Prevent the battery from moving freely inside the battery
compartment. Always use the battery clamp to secure the
battery in the battery compartment.
•Examine the battery, charger and its connector for
excessive wear or damage each time you charge the
battery. If damage is detected, do not use the charger
or the battery until you have replaced the worn or
damaged part.
•Always remove an exhausted battery from the vehicle.
Battery leakage and corrosion can damage the vehicle.
•Your Power Wheels®battery is a sealed lead-acid
battery. It must be recycled or disposed of in an
environmentally sound manner.
•Do not dispose of a lead-acid battery in your regular,
household trash. The incineration, landfilling or mixing of
sealed lead-acid batteries with household trash is
prohibited by law in most areas.
•Do not dispose of a lead-acid battery in a fire. The battery
may explode or leak.
•Return exhausted batteries to a federal or state
approved lead-acid battery recycler, such as a Power
Wheels®authorized service center, or a local seller of
automotive batteries. For the service center location
nearest you, please call 1-800-348-0751. Contact your
local waste management officials for other information
regarding the environmentally sound collection,
recycling and disposal of lead-acid batteries. If you live
in the State of Florida or Minnesota, it is prohibited by
law for anyone to throw away lead-acid batteries in the
municipal waste stream.
Care Disposal

Use vehicle on generally level ground ONLY!
Rules for Safe Driving
J
Teach Safety Rules to Children
While children can quickly develop the skill necessary to
drive this vehicle, it is important to remember that their
judgment skills are still very immature. Unsupervised
driving by children can lead to serious injury. Before
children use this vehicle, an adult should carefully
evaluate the driving area as well as the children’s skill
level and ability to drive this vehicle safely. Children are
not always able to recognize or anticipate hazards, even
when they have been taught about them. THERE IS NO
ACCEPTABLE SUBSTITUTE FOR DIRECT ADULT
SUPERVISION.
Teach appropriate safety rules to your child before
allowing operation of this vehicle. These rules should also
be reviewed with neighborhood children or other playmates
who want to drive this vehicle.
Riding Rules
Make sure children know and follow these rules for
safe driving:
1. Always sit on the seat.
2. Always wear shoes.
3. Only 2 (two) riders at a time. A child who is not sitting
on the seat or who is standing on the vehicle could fall
off, cause a tip-over or block the driver’s view. A child
could be seriously injured.
4. Do not allow any child to drive the vehicle in the street
or near moving (motorized) vehicles.
5. Do not allow any child to drive near bodies of water
(such as pools or creeks), obstructions (such as
furniture, low tree limbs or play equipment), or drop-offs
(such as stairs or decks).
6. Do not allow any child to drive the vehicle in the dark.
A child could encounter unexpected obstacles and have
an accident. Operate the vehicle only in the daytime or
a well-lit area.
7. Do not allow your child to drive on sloped or inclined
surfaces. Restrict your child’s driving to generally level
ground ONLY!
8. Do not allow your child to drive down or across a
steep slope.
-The vehicle may gain unsafe speed, even if the pedal
is released to stop.
-The vehicle may tilt and tip over.
-The wheels could lose traction, causing the vehicle
to slip.
9. Do not allow your child to drive up steep inclines. The
motor may stop and the vehicle could roll backwards at
an unsafe speed.
10. Never put anything near any moving parts. Rotating
parts such as motors, gear boxes and wheels can snag
fingers, hair, etc., causing serious injury. Do not allow
operation of the vehicle when it is on its side or in an
upside-down position.
11. Do not operate the vehicle near flammable vapors
(gasoline, paint thinner, acetone, liquid wax, etc.).
The vehicle’s electrical switches, like most electrical
switches, emit an internal spark when first turned on or
turned off. The presence of flammable liquids or vapors
could cause an explosion or a fire. Keep all flammable
products in tightly sealed containers and away from
the vehicle.
12. Do not allow a child to operate the vehicle without
direct adult supervision. To prevent unsupervised use of
the vehicle, disconnect the motor harness from the
battery when the vehicle is not in use.
To disconnect the motor harness connector
and battery:
•Unfasten the hood latches and raise the hood.
•Unplug the motor harness connector from the battery.
•Lower the hood and fasten the hood latches.
WARNING
Prevent Injuries and Deaths
•Direct Adult Supervision Required.
•Keep Children Within Safe Riding Areas
These areas must be:
- away from swimming pools and other
bodies of water to prevent drownings.
- generally level to prevent tipovers.
- away from steps, driveways, cars,
roads and alleys.
RIDING HAZARD
20