Fisher-Price V6910 User manual

www.fisher-price.com
V6910
Please keep this instruction sheet for future reference,
as it contains important information.
Requires four “AA” (LR6) alkaline batteries (not included).
Adult assembly is required for battery installation.
Tool required for battery installation: Phillips screwdriver (not included).
Wipe this toy with a clean, damp cloth.
This toy has no consumer serviceable parts. Do not take this toy apart.
Do not apply heavy pressure or force to the drawing screen.

Battery
Installation
Protect the environment by not•
disposing of this product with
household waste (2002/96/EC).
Check your local authority for
recycling advice and facilities
(Europe only).
Locate the battery compartment on the•
back of the toy.
Loosen the screws in the battery•
compartment door with a Phillips
screwdriver. Remove the battery
compartment door.
Insert four “AA” (LR6)• alkaline
batteries, as indicated inside the
battery compartment.
Hint: We recommend using alkaline
batteries for longer battery life.
Replace the battery compartment door•
and tighten the screws with a Phillips
screwdriver. Do not over-tighten.
If this product begins to operate erratically,•
you may need to reset the electronics.
Slide the power/mode switch off and then
back on.
When lights become faint or stop, it’s time•
for an adult to change the batteries!
In exceptional circumstances, batteries may
leak fluids that can cause a chemical burn
injury or ruin your product. To avoid
battery leakage:
Do not mix old and new batteries or•
batteries of different types: alkaline,
standard (carbon-zinc) or rechargeable
(nickel-cadmium).
Insert batteries as indicated inside the•
battery compartment.
Remove batteries during long periods•
of non-use. Always remove exhausted
batteries from the product. Dispose of
batteries safely. Do not dispose of this
product in a fire. The batteries inside may
explode or leak.
Never short-circuit the battery terminals.•
Use only batteries of the same or•
equivalent type, as recommended.
Do not charge non-rechargeable batteries.•
Remove rechargeable batteries from the•
product before charging.
If removable, rechargeable batteries are•
used, they are only to be charged under
adult supervision
Battery Safety
Information
1,5V x 4
“AA” (LR6)
Battery Compartment Door

BACK VIEW
Let’s Draw!
Erasing
Light it Up!
Slide a tracing template or your own•
personal image into the slot in the back of
the toy.
Use one of the included glow markers to•
trace the design or create a design of your
own without the template!
Hints:
Draw thin lines to create a "neon" effect. •
Be sure to let markings dry at least •
15 seconds before touching.
Stand up the extra markers in the drawer •
for easy access while you work!
Slide the power/mode switch to blink•
or glow mode.
Glow Mode - lights up your creation!
Blink Mode - makes your creation
"magically" appear and disappear.
When you are finished playing with this•
toy, slide the power/mode switch OFF .
Mode Switch
1
2
Wipe the drawing surface with a damp•
cloth after each use to completely remove
the glow marker.
Use only the glow markers provided on•
the drawing screen. Markers may stain
fabrics and other surfaces. Avoid contact
with carpet, clothing, walls and furniture.
Do not use permanent markers on the
drawing surface. Adult supervision is
recommended.
To remove marker from the skin, simply•
use soap and water.

Consumer Information
FCC Statement (United States Only)
This equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy
and, if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the
user is encouraged to try to correct the
interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.•
Increase the separation between the•
equipment and receiver.
Consult the dealer or an experienced radio/•
TV technician for help.
Note: Changes or modifications not
expressly approved by the manufacturer
responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
CO
N
SU
MER
ASS
I
S
T
A
N
C
E
1-800-432-5437 (US & Canada)
1300 135 312 (Australia)
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, NY 14052.
Hearing-impaired consumers: 1-800-382-7470.
Outside the United States:
Canada: Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2; www.service.mattel.com.
Great Britain: Mattel UK Ltd, Vanwall Business Park,
Maidenhead SL6 4UB. Helpline: 01628 500303.
www.service.mattel.com/uk
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
New Zealand: 16-18 William Pickering Drive,
Albany 1331, Auckland.
NMB-003
Cet appareil numérique de la classe B•
est conforme à la norme NMB-003 du
Canada. L’utilisation de ce dispositif
est autorisée seulement aux conditions
suivantes: (1) il ne doit pas produire de
brouillage et (2) l’utilisateur du dispositif
doit être prêt à accepter tout brouillage
radioélectrique reçu, meme si ce brouillage
est susceptible de compromettre le
fonctionnement du dispositif.
ICES-003
This Class B digital apparatus complies•
with Canadian ICES-003. Operation is
subject to the following two conditions:
(1) this device may not cause harmful
interference and (2) this device must
accept any interference received,
including interference that may cause
undesired operation.
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2010 Mattel, Inc. All Rights Reserved. ®
and
™designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA V6910pr-0920
Snap the markers into the storage slots•
and insert the tracing templates into the
slot on the back of the toy.
Hint: Replace the caps tightly on the
markers to prevent them from drying out.