Fisher Scientific Isotemp User manual

User's Manual
Manual P/N U01318
Rev. 11/05/2015
Isotemp®
Shaking and General
Purpose Water Baths

Table of Contents
Quick Start Guides
Preface ........................................................................................................................................... P-1
Compliance ......................................................................................................................... P-1
Unpacking ........................................................................................................................... P-1
After-Sale Support ............................................................................................................... P-1
Warranty.............................................................................................................................. P-2
Chapter 1 Safety ................................................................................................................................ 1-1
Safety Factors...................................................................................................................... 1-1
Chapter 2 General Information.......................................................................................................... 2-1
Description .......................................................................................................................... 2-1
Intended Use ....................................................................................................................... 2-1
Specifications ...................................................................................................................... 2-2
Chapter 3 Installation ........................................................................................................................ 3-1
Bath Installation ................................................................................................................... 3-1
Ventilation............................................................................................................................ 3-1
Cover Installation ................................................................................................................. 3-1
Electrical Requirements........................................................................................................ 3-2
Approved Fluids................................................................................................................... 3-3
Filling Requirements............................................................................................................. 3-6
Filling with Thermal Lab Beads ............................................................................................. 3-6
Draining .............................................................................................................................. 3-7
Accessories......................................................................................................................... 3-7
Drain Kit Accessory.............................................................................................................. 3-7
Chapter 4 Operation........................................................................................................................... 4-1
Controller............................................................................................................................. 4-1
Start Up............................................................................................................................... 4-2
Changing the Set Point......................................................................................................... 4-3
Viewing/Changing the Shaker Speed..................................................................................... 4-3
Changing a Setting .............................................................................................................. 4-4
Selecting a Preset................................................................................................................ 4-6
Changing a Preset ............................................................................................................... 4-6
Temperature Display ............................................................................................................ 4-7
Shut Down........................................................................................................................... 4-7
Chapter 5 Preventive Maintenance................................................................................................... 5-1
Cleaning.............................................................................................................................. 5-1
Electrical Power Cord........................................................................................................... 5-2
Optical Disc......................................................................................................................... 5-2
Shaker Assembly ................................................................................................................. 5-2
Chapter 6 Troubleshooting ................................................................................................................ 6-1
Error Displays ...................................................................................................................... 6-1
Checklist ............................................................................................................................. 6-2

Isotemp Fisher Scientific

Isotemp Water Bath Quick Start Guide
This quick start guide is intended for initial start up only. For all other procedures you must refer to the manual. Also, if any
of these steps are not clear refer to the manual before proceeding.
Filling (Only approved fluids are Filtered/Single Distilled Water and De-ionized Water)
Ensure the reservoir drain port is closed and that all plumbing connections are securely plumbed or capped. Also ensure any residue is
thoroughly removed from the reservoir before filling.
To avoid spilling, place your samples/trays into the bath before filling.
Slowly fill the reservoir. When adding, point the opening of a container away from yourself.
For Shaking Water Baths, fill the reservoir with a minimum of one inch of water and the maximum level lower than the tray shaft fitting.
Make allowance for water splashing from tray oscillations.
For GPD Baths, fill the reservoir with a minimum of one inch of water and a maximum level one inch lower than the tank upper surface.
Starting
Do not run the bath until fluid is added to the reservoir. Have extra fluid on hand. If the bath does not start refer to the manual.
•Place the circuit protector located on the rear of the bath to the Iposition.
•The screen will momentarily display and then the home screen appears displaying the set point and the audible alarm status.
The set point is the desired reservoir fluid temperature.
30.0°C
appears on Shaking
Water Baths only.
Page 1 of 2
20.1°C
30.0°C
Press to start the bath and display the fluid temperature. If the reservoir fluid
temperature is below the set point the heater will start.

Changing the Set Point
When operating without a lid, limit the maximum set point to 60°C.
You can change the set point with the bath running or not. From the home screen press either arrow key to display:
29.9°C
50.0°C
x
Press, and hold, the arrow keys to bring up the desired set point value. The range is 5°C
to 100°C. Once the desired value is displayed, in this case 50.0°C, press the soft key
below to save the change or press the soft key below
x
to not save the
change. The display returns to the home screen. Note After a 30 second delay if neither
key is pressed the display returns to the home screen, any change is
not saved.
Viewing/Changing the Shaker Speed (SWB only)
You can view/change the speed value with the bath running or not. From the home screen press the soft key below to display:
Press, and hold, the arrow keys to bring up the desired value. The values are 0 and 30 to
200. Once the desired value is displayed press or to save the change
and return to the home screen.
2 RPM0
Selecting a Preset
You can select a preset with the bath running or not.
From the home screen press :
Use the arrow keys to select the desired preset. Once the desired preset is highlighted
press the soft key below to save the change and return to the home screen.
Note After a 30 second delay if neither key is pressed the display returns to the home
screen, any change is
not saved.
Page 2 of 2
T1 37.0°C 30 RPM
T2 50.0°C 50 RPM
T3 55.0°C 70 RPM
产品中有害物质的名称及含量
China EEP Hazardous Substances Information
http://www.thermofisher.com/us/en/home/technical-resources/rohs-certificates.html

Kurzanleitung
Diese Kurzanleitung ist nur für die erste Inbetriebnahme vorgesehen. Für alle anderen Verfahren müssen Sie im Handbuch
nachsehen. Auch wenn irgendwelche Schritte unklar sind, schaue Sie im Handbuch nach, bevor Sie fortfahren.
Befüllung
Stellen Sie sicher, dass der Ablauf des Behälters geschlossen ist und dass alle Anschlüsse sicher angeschlossen oder verschlossen sind.
Achten Sie außerdem darauf, dass vor dem Befüllen des Behälters alle Rückstände gründlich entfernt wurden.
Um ein Überlaufen zu vermeiden, stellen Sie die zu temperierenden Proben/Tabletts vor dem Befüllen in das Bad.
Füllen Sie den Behälter langsam. Halten Sie den Behälter beim Einfüllen so, dass seine Öffnung von Ihnen weg zeigt.
Füllen Sie bei Rüttel-Wasserbädern den Behälter mindestens bis zu einer Füllhöhe von 2,5 cm mit Wasser, und höchstens bis unterhalb der
Halterung für den Tablettschaft. Lassen Sie etwas Platz für Spritzwasser durch die Schwingungen des Tabletts.
Für GPD-Bäder füllen Sie den Behälter mindestens bis zu einer Füllhöhe von 2,5 cm mit Wasser, und bis maximal 2,5 cm unterhalb des
Flüssigkeitsstandes im oberen Tank.
Starten
Lassen Sie das Gerät erst laufen, nachdem Sie die Badflüssigkeit hinzugegeben haben. Halten Sie zusätzliche Flüssigkeit griffbereit. Wenn
das Gerät nicht startet, sehen Sie im Handbuch nach.
• Stellen Sie den Schalter an der Rückseite des Bades auf die Position I.
• Der Bildschirm geht sofort an , dann erscheint der Einstiegsbildschirm mit dem Sollwert und einem akustischen Statusalarm.
Der Sollwert ist die gewünschte Temperatur der Behälterflüssigkeit.
30.0°C
Seite 1 von 2
20.1°C
30.0°C
Drücken Sie zum Starten des Bades und zur Anzeige der Flüssigkeitstemperatur.
Liegt die Temperatur der Flüssigkeit im Behälter unterhalb der Sollwerttemperatur, so wird
die Heizung eingeschaltet.
erscheint nur an Rüttel-
Wasserbädern.

Ändern des Sollwertes
Beim Betrieb ohne Abdeckung ist der Sollwert auf maximal 60 °C zu begrenzen.
Sie können den Sollwert ändern, gleichgültig, ob das Bad läuft oder nicht. Vom Einstiegsbildschirm aus drücken Sie eine der beiden
Pfeiltasten zur Anzeige von:
29.9°C
50.0°C
x
Drücken Sie die Pfeiltasten und halten Sie diese gedrückt , bis der gewünschte Sollwert
erscheint. Der Temperaturbereich reicht von 5 °C bis 100 °C. Wird der gewünschte Wert
angezeigt, in diesem Fall 50,0 °C, so drücken Sie die Schaltfläche unten , um
die Änderung zu speichern, oder drücken Sie die Schaltfläche unten
x
, um die
Änderung nicht abzuspeichern.
Die Anzeige kehrt zum Einstiegsbildschirm zurück. Beachten Sie bitte, dass nach einer
Verzögerung von 30 Sekunden, wenn keine der beiden Tasten gedrückt wird, die Anzeige
zum Einstiegsbildschirm zurückkehrt. Änderungen werden dann nicht gespeichert.
Anzeigen/ändern der Rüttelgeschwindigkeit (nur SWB)
Die Geschwindigkeitseinstellung lässt sich sowohl bei eingeschaltetem als auch bei ausgeschaltetem Bad anzeigen/ändern. Vom
Einstiegsbildschirm aus drücken Sie die Schaltfläche unten zur Anzeige von:
Drücken Sie die Pfeiltasten, und halten Sie diese gedrückt, bis der gewünschte Wert
erscheint. Die Werte sind 0 und 30 bis 200. Wird der gewünschte Wert angezeigt, drücken
Sie oder , um die Änderung zu speichern und zum Einstiegsbildschirm
zurückzukehren.
2 RPM0
Auswahl eines voreingestellten Sollwertes
Sie können den voreingestellten Sollwert auswählen, gleichgültig, ob das Bad läuft oder
nicht.
Vom Einstiegsbildschirm aus drücken Sie :
Verwenden Sie bitte die Pfeiltasten zur Auswahl des gewünschten Sollwertes.
Sobald der gewünschte Sollwert erscheint, drücken Sie bitte die Schaltfläche unten
, um die Änderung zu speichern und zum Einstiegsbildschirm zurückzukehren.
Beachten Sie bitte dass nach einer Verzögerung von 30 Sekunden, wenn keine der beiden Tasten gedrückt wird, die Anzeige zum
Einstiegsbildschirm zurückkehrt. Änderungen werden dann nicht gespeichert.
Seite 2 von 2
T1 37.0°C 30 RPM
T2 50.0°C 50 RPM
T3 55.0°C 70 RPM

Guide de démarrage rapide
Ce guide de démarrage rapide est destiné à la mise en marche initiale uniquement. Pour toute autre procédure, merci
de vous référer au manuel. De plus, si l’une de ses étapes ne vous paraît pas claire, téléchargez le manuel avant de
commencer.
Remplissage
Assurez-vous que le port de vidange du réservoir est fermé et que tous les tuyaux sont soit branchés, soit rebouchés. Vérifiez également
qu’il ne reste plus aucun résidu dans le réservoir avant de le remplir.
Pour éviter les éclaboussures, placez les échantillons/plateaux dans le bain avant de remplir ce dernier.
Remplissez lentement le réservoir en maintenant l’ouverture du conteneur à distance.
Pour les bains à agitation, remplissez le réservoir d’au moins 2,5 centimètres (1 pouce) d’eau et assurez-vous que le niveau maximum est
inférieur à celui de la pièce d’entraînement du plateau. Prenez en compte les éclaboussures dues aux oscillations du plateau.
Pour les bains GPD, remplissez le réservoir d’au moins 2,5 centimètres (1 pouce) d’eau et assurez-vous que le niveau maximum se trouve
2,5 centimètres (1 pouce) en dessous de la surface du réservoir supérieur.
30.0°C
s’affiche pour les bains à
agitation uniquement.
Page 1 sur 2
20.1°C
30.0°C
Démarrage
Ne faites pas fonctionner le bain tant que le réservoir ne contient pas de liquide. Conservez une quantité de liquide supplémentaire à
proximité. Si le bain ne démarre pas, reportez-vous au manuel.
• Placez le dispositif de protection des circuits situé à l’arrière du bain sur la position I.
• s’affichera momentanément à l’écran, puis l’écran d’accueil s’affiche et indique la température définie et le statut de
l’alarme sonore. La température définie correspond à la température souhaitée pour le liquide contenu dans le réservoir.
Appuyez sur pour démarrer le bain et afficher la température du liquide.
Si la température du liquide se trouvant dans le réservoir est inférieure à la température
définie, le réchauffeur se met en marche.

Modification de la température définie
Si vous utilisez le bain sans couvercle, définissez la température maximum à 60 °C.
Vous pouvez modifier la température définie que le bain soit ou non en cours d’utilisation. À l’écran d’accueil, appuyez sur une touche
flèche pour afficher :
29.9°C
50.0°C
x
Appuyez sur les touches flèche et maintenez-les enfoncées jusqu’à atteindre la valeur de
température définie désirée. La plage de valeurs va de 5 °C à 100 °C. Une fois que la
valeur désirée est affichée, dans ce cas 50 °C, appuyez sur la touche se trouvant sous
pour enregistrer la modification ou sur la touche sous
x
pour ne pas
enregistrer la modification. L’affichage retourne à l’écran d’accueil.
Affichage/modification de la vitesse d’agitation (SWB uniquement)
Vous avez la possibilité d’afficher/de modifier la vitesse, que le bain soit en cours d’utilisation ou non. À l’écran d’accueil, appuyez sur la
touche se trouvant sous pour afficher :
Appuyez sur les touches flèche et maintenez-les enfoncées jusqu’à atteindre la valeur
désirée. Les valeurs sont 0 et de 30 à 200.
Une fois que la valeur désirée est affichée, appuyez sur ou pour
enregistrer la modification et revenir à l’écran d’accueil.
2 RPM0
Sélection d’une température prédéfinie
Vous pouvez sélectionner une température prédéfinie, que le bain soit ou non en cours
d’utilisation.
À l’écran d’accueil, appuyez sur :
Utilisez les touches flèche pour sélectionner la valeur de température définie désirée. Une fois la valeur désirée en surbrillance, appuyez
sur la touche se trouvant sous pour enregistrer la modification et retourner à l’écran d’accueil.
Remarque Au bout de 30 secondes, si vous n’avez appuyé sur aucune de ces deux touches, l’affichage retourne à l’écran d’accueil et les
modifications effectuées, le cas échéant, ne sont pas sauvegardées.
Page 2 de 2
Remarque Au bout de 30 secondes, si vous n’avez appuyé sur aucune de ces deux touches, l’affichage retourne à l’écran d’accueil et les
modifications effectuées, le cas échéant, ne sont pas sauvegardées.
T1 37.0°C 30 RPM
T2 50.0°C 50 RPM
T3 55.0°C 70 RPM

Guía de inicio rápido
Esta guía de inicio rápido se ha creado únicamente para el arranque inicial. Para obtener información sobre el resto de
procedimientos, debe consultar el manual. Asimismo, en caso de que tuviera dudas sobre alguno de estos pasos, consulte
el manual antes de continuar.
Llenado
Asegúrese de que el puerto de drenaje del depósito está cerrado y de que todas las conexiones de tuberías se han conectado y tapado
correctamente. Asimismo, asegúrese de que se han eliminado todos los residuos del depósito antes de proceder al llenado.
Para evitar salpicaduras, introduzca las muestras/bandejas en la bañera antes de llenarla.
Llene el depósito lentamente. Al añadir agua, coloque la apertura de un contenedor lejos de usted.
En el caso de bañeras de agua con agitación, llene el depósito con una cantidad mínima equivalente a dos centímetros y medio de agua y
un nivel máximo que sea inferior al ajuste del eje de la bandeja. Tenga en cuenta las salpicaduras de agua procedentes de las oscilaciones
de la bandeja.
En el caso de bañeras GPD, llene el depósito con un mínimo de dos centímetros y medio de agua y un nivel máximo de dos centímetros y
medio pro debajo de la superficie superior del tanque.
Puesta en marcha
30.0°C
20.1°C
30.0°C
No ponga en marcha la bañera hasta que se haya añadido líquido al depósito. Tenga a mano algo de líquido adicional. Si la unidad no
llegara a ponerse en marcha, consulte el manual.
• Coloque el protector de circuitos, situado en la parte posterior de la bañera, en la posición I.
• La pantalla aparecerá momentáneamente y, a continuación, aparecerá la pantalla de inicio mostrando el punto de ajuste y el
estado de la alarma audible. El punto de ajuste es la temperatura deseada del fluido del depósito.
solo aparece en bañeras de
agua con agitación.
Pulse para poner en marcha la bañera y mostrar la temperatura del fluido.
Si la temperatura del fluido del depósito está por debajo del punto de ajuste, se pondrá en
marcha el calentador .
Página 1 de 2

Modificación del punto de ajuste
Cuando se opere sin tapa, limite el punto de ajuste máximo a 60 °C.
Puede cambiar el punto de ajuste con la bañera en marcha o parada.
29.9°C
50.0°C
x
Visualización/modificación de la velocidad del agitador (solo SWB)
Puede ver/modificar el valor de la velocidad con la bañera en marcha o parada. En la pantalla de inicio, pulse la siguiente tecla
multifunción para mostrar:
Pulse y mantenga pulsadas las teclas de flecha para que aparezca el valor deseado. Los
valores pueden ser 0 y de 30 a 200.
Una vez que aparezca el valor deseado, pulse o para guardar los
cambios y volver a la pantalla de inicio.
2 RPM0
Selección de un punto de ajuste predeterminado
Puede seleccionar un punto de ajuste predeterminado con la bañera en marcha o parada.
En la pantalla de inicio, pulse :
Utilice las teclas de flecha para seleccionar el valor del punto de ajuste deseado. Una vez
que aparezca resaltado el punto de ajuste, pulse la siguiente tecla multifunción
para guardar los cambios y volver a la pantalla de inicio.
En la pantalla de inicio, pulse cualquier tecla de flecha para mostrar:
Pulse y mantenga pulsadas las teclas de flecha para que aparezca el valor del punto
de ajuste deseado. El rango se encuentra comprendido entre 5 °C y 100 °C. Una vez
que aparezca el valor deseado, en este caso 50 °C, pulse la siguiente tecla multifunción
para guardar los cambios, o pulse la siguiente tecla multifunción
x
para
no guardarlos. El visualizador vuelve a la pantalla de inicio.
Nota Una vez transcurridos 30 segundos, y si el visualizador vuelve a la pantalla de inicio
si no se pulsa ninguna tecla, no[se guarda ningún cambio.
Nota Una vez transcurridos 30 segundos, y si el visualizador vuelve a la pantalla de inicio si no se pulsa ninguna tecla, [3]no[4] se guarda
ningún cambio.
Página 2 de 2
T1 37.0°C 30 RPM
T2 50.0°C 50 RPM
T3 55.0°C 70 RPM

Guia de início rápido
Este guia de início rápido destina-se apenas ao arranque inicial. Para todos os outros procedimentos, consulte o manual.
Além disso, se qualquer uma dessas etapas não estiver clara, consulte o manual antes de prosseguir.
Preenchimento
Certifique-se de que a porta de drenagem do reservatório esteja fechada e que todas as conexões do encanamento estejam firmemente
sondadas ou tampadas. Também garanta que qualquer resíduo seja cuidadosamente removido do reservatório antes do preenchimento.
Para evitar o derramamento, coloque as amostras/bandejas no banho antes do enchimento.
Encha lentamente o reservatório.
Enquanto adiciona, aponte a abertura do recipiente para longe de você. Para banhos de água agitados, encha o reservatório com, no
mínimo, uma polegada de água e o nível máximo mais baixo que a conexão do eixo da bandeja. Deixe uma folga para respingos de água
durante as oscilações da bandeja.
Para Banhos GPD, encha o reservatório com, no mínimo, uma polegada de água e um máximo nível de uma polegada por baixo da
superfície superior do tanque.
30.0°C
Página 1 de 2
20.1°C
30.0°C
Iniciando
Não execute o banho até que o fluido seja adicionado ao reservatório. Tenha fluido adicional em mãos. Se o banho não começar, consulte
o manual.
• Mova o protetor de circuito, localizado na parte traseira do banho, para a posição I.
• A tela irá exibir momentaneamente e, em seguida, a tela inicial aparecerá exibindo o ponto de ajuste e o status do alarme
sonoro. O ponto de ajuste é a temperatura desejada do fluido do reservatório.
aparece somente em Banhos de
água agitados.
Pressione para iniciar o banho e exibir a temperatura do fluido. Se a temperatura
do fluido do reservatório estiver abaixo do ponto de ajuste, o aquecedor será
iniciado.

29.9°C
50.0°C
x
2 RPM0
Página 2 de 2
Seleção de um ponto de ajuste pré-definido
Visualizar/alterar a velocidade do agitador (apenas SWB)
Você pode visualizar/alterar a velocidade com o banho funcionando ou parado. Na tela inicial, pressione a tecla de função abaixo
para exibir:
Pressione e segure as teclas de seta para exibir o valor desejado. Os valores são 0 e 30 a
200. Quando o valor desejado for exibido, pressione ou para salvar a
alteração e voltar à tela inicial.
Alterar o Ponto de ajuste
Ao operar sem tampa, limite o ponto máximo definido para 60 °C.
Você pode alterar o ponto de ajuste com o banho funcionando ou parado. A partir da tela inicial, pressione qualquer tecla de seta para
exibir:
Pressione e segure as teclas de seta para mostrar o valor de ajuste desejado. A variação
é de 5 °C a 100 °C. Quando o valor desejado for exibido, neste caso, 50 °C, pressione
a tecla programável abaixo para salvar a alteração ou pressione a tecla
programável abaixo
x
para não salvar a alteração. A tela retorna à tela inicial.
Nota Depois de um intervalo de 30 segundos, se nenhuma tecla for pressionada, a tela
retornará para a tela inicial, e as alterações não serão salvas.
Você pode selecionar um ponto de ajuste pré-definido com o banho funcionando ou
parado.
A partir da tela inicial, pressione :
Use as setas de seta para selecionar o valor de ponto de ajuste desejado.
Quando o ponto de ajuste desejado estiver realçado, pressione a tecla programável abaixo para salvar a alteração e voltar à tela
inicial.
Nota Depois de um intervalo de 30 segundos, se nenhuma tecla for pressionada, a tela retornará para a tela inicial, e as alterações não
serão salvas.
T1 37.0°C 30 RPM
T2 50.0°C 50 RPM
T3 55.0°C 70 RPM

Isotemp |P-1Fisher Scientific
| Preface
Preface
Compliance
The Declaration of Conformity is available upon request.
Unpacking
The bath is supplied with an electrical power cord. Do not discard the packaging until the cord is
located and the bath is operating.
If the bath shows external or internal damage contact the transportation company and file a
damage claim. Under ICC regulations, this is your responsibility.
The bath does not have handles. Take into account its weight when unpacking and
transporting. We recommend two people lift heavier baths from the bottom.
After-sale Support
Fisher Scientific is committed to customer service both during and after the sale. If you have
questions concerning the bath operation, or questions concerning spare parts or Service
Contracts, call our Sales, Service and Customer Support.
Before calling, please obtain the following information:
•bath model number
•bath serial number
•power source voltage
The bath’s model number and serial number are located on the nameplate label on the rear of the
bath.
CAUTION

P-2 |Isotemp Fisher Scientific
Preface |
Warranty
The Isotemp®products distributed by Fisher Scientific ("Fisher"), Fisher warrants to the direct
purchaser that the product will be free from defects in material or workmanship for a period of
one year from the date of delivery. Fisher will repair or replace the product or provide credit, as its
sole option, upon prompt notification and compliance with its instructions.
The Distributor warrants to Customer that upon prompt notification and compliance with
Distributor's instructions, that the Distributor will repair or replace, at Distributor's sole option, any
Product which is defective in material or workmanship.
Distributor expressly disclaims all other warranties, whether expressed, implied or statutory,
including the warranties of merchantability, and fitness for a particular purpose. Distributor's sole
responsibility and the Customer's exclusive remedy for any claim arising out of the purchase of
any Product is repair or replacement, as described above. In no event shall Distributor's liability
exceed the purchase price paid therefore; nor shall Distributor be liable for any claims, losses or
damage of any third party or for lost profits or any special, indirect, incidental, consequential, or
exemplary damages, howsoever arising, even if Distributor has been advised of the possibility of
such damages.

Isotemp |1-1Fisher Scientific
Safety | Chapter 1
1
DANGER
WARNING
CAUTION
Chapter 1 Safety
Safety Factors
Make sure you read and understand all instructions and safety precautions listed in this manual
before installing or operating your bath. If you have any questions concerning the operation of
your bath or the information in this manual, please contact us.
The are no special personal protective equipment requirements needed to perform normal
operation. We do recommend always wearing eye protection and gloves.
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death
or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or
moderate injury. It is also be used to alert against unsafe practices.
The lightning flash with arrow symbol, within an equilateral triangle, is intended to alert the user
to the presence of non-insulated "dangerous voltage" within the bath's enclosure. The voltage
magnitude is significant enough to constitute a risk of electrical shock.
This label indicates the presence of hot surfaces.
This label indicates read the manual.
This label indicates a hand crushing hazard. (Shaking Water Bath only)
Observe all warning labels.
Never remove warning labels.

1-2 |Isotemp Fisher Scientific
Chapter 1 |Safety
The bath's construction provides protection against the risk of electrical shock by grounding appropriate
metal parts. The protection will not function unless the power cord is connected to a properly grounded
outlet. It is the user's responsibility to assure a proper ground connection is provided.
Do not use the bath as a sterile or patient connected device. In addition, the bath is not designed for use
in Class I, II or III locations as defined by the National Electrical Code.
The circuit protector located on the rear of the bath is not intended to act as a disconnecting means. The
bath's power cord is used as the disconnecting device, it must be easily accessible at all times.
Never operate the bath with a damaged line cord.
Never place the bath in a location or atmosphere where excessive heat, moisture, or corrosive materials
are present.
Never operate the bath without fluid in the reservoir. The only approved fluid is water. General Purpose
Baths may also use lab armor beads.
Never operate the bath or add fluid to the reservoir with panels removed.
Operating the baths at high temperature will cause condensation on the underside of the cover. Remove
the cover with care so the water falls back into the reservoir and not on the bath surface.
When operating at high temperatures do not touch the cover surface, always use the cover's knob/handle.
The user is responsible for any hazard rising from heated material.
Do not clean the bath with solvents, only use a soft cloth and water.
Drain the bath before it is moved. Drain the bath before it is transported and/or stored. Store the bath in
the temperature range -25°C to 60°C (with packaging), and <80% relative humidity.
Always turn the bath off and disconnect the supply voltage from its power source before moving the bath
or before performing any service or maintenance procedures.
Transport the bath with care. Sudden jolts or drops can damage its components.
An operating shaking water bath has moving components. Do not insert appendages between the
reservoir wall and rack. We recommend stopping the shaker table when loading/removing samples or
vessels.
Refer service and repairs to a qualified technician.
Performance of installation, operation, or maintenance procedures other than the ones described in this
manual may result in a hazardous situation and will void the manufacturer's warranty.

Isotemp |2-1Fisher Scientific
Operation | Chapter 2
2
Chapter 2 General Information
Description
All Fisher ScientificTM Isotemp Water Baths provide constant temperature to applications placed
in the reservoir. All have digital displays, four programmable set point temperatures, acoustic and
optical alarms, and offer adjustable high temperature protection.
The interior of the bath is constructed of stainless steel and is designed for operation with water.
The body is made from galvanized steel and is painted for added protection. A drain is located
at the far left hand end of the bath. A stainless steel gable cover, required to maintain optimal
temperature sensitivity, is also provided with the bath.
The nameplate label on the bath identifies its electrical requirements.
Intended Use
The baths are intended for use in research and quality control.
They are intended for use by a qualified lab technician trained in basic laboratory procedures and
safety protocols. Also, for indoor use in a laboratory environment on a bench top only.

2-2 |Isotemp Fisher Scientific
Chapter 2 |Operation
Shaking Water Bath Specifications
Low-end temperatures require supplemental cooling.
Specifications obtained at sea level using water.
Bath depth includes bezel, height does not include lid.
Fisher Scientific takes no responsibility for damages caused by the selection of an unapproved fluids.
Fisher Scientific reserves the right to change specifications without notice.
SWB 15 SWB 27
Reservoir Fluid Control
Temperature °C
°F
Ambient +5 to 100
Ambient +9 to 212
Set Point Temperature
Range°C
°F
+5 to 100
+9 to 212
Ambient Temperature °C
Range °F
+15 to 45
+59 to 113
Stability/Uniformity
@37°C ±0.1/±0.05
Heating Output watts 1200 1500
Bath Volume liters 15 27
Overall Bath Dimensions
(L x W x H) cm
inches
39.4 x 63.2 x 24.9
15.5 x 24.9 x 9.8
39.4 x 93.8 x 24.9
15.5 x 36.9 x 9.8
Bath Work Area
Dimensions
(L x W x H) cm
inches
29.2 x 30.5 x 16.5
11.5 x 12.0 x 6.5
29.2 x 61.0 x 16.5
11.5 x 24.0 x 6.5
Tray Dimensions
(L x W x D) cm
inches
28.9 x 30.8 x 14.8
11.3 x 12.1 x 5.8
28.9 x 61.5 x 14.8
11.3 x 24.2 x 5.8
Tray Depth cm
inches
8.9
3.5
Shaking Speed rpm 0 and 30 - 200
Stroke Length mm 26
Max Tray Load kg
lb
9
20
14
30
Bath Weight kg
lb
22.2
48.0
27.2
62.0
Electrical
Requirements (VAC/Hz)
(Voltage ±10%)
100-115/50-60
or
200-230/50-60
Compliance CE RoHS
UL WEEE
Maximum Relative
Humidity
(Non Condensing)
80% (up to 31°C)
80% (up to 88°F)
Operating Altitude meters
feet
Sea Level to 2000
Sea Level to 6560
Overvoltage Category II
Pollution Degree 2
Storage Temperature °C
Range °F
-25 to +60
-13 to +140

Isotemp |2-3Fisher Scientific
Operation | Chapter 2
General Purpose Water Bath Specifications
Low-end temperatures require supplemental cooling.
Specifications obtained at sea level using water.
Thermal beads may be used instead of water but they will degrade the bath's uniformity and stability.
Bath depth includes bezel, height does not include lid.
Fisher Scientific takes no responsibility for damages caused by the selection of an unapproved fluids.
Fisher Scientific reserves the right to change specifications without notice.
GPD 02 GPD 2S GPD 05 GPD 10
Reservoir Fluid Control
Temperature °C
°F
Ambient to 90
Ambient to 194
Ambient to 100
Ambient to 212
Set Point Temperature
Range°C
°F
+5 to 100
+9 to 212
Ambient Temperature °C
Range °F
+15 to 45
+59 to 113
Stability @37°C ±0.1
Uniformity @37°C ±0.2
Heating Output watts 200 300 300 800
Bath Volume liters 22510
Overall Bath Dimensions
(L x W x H) cm
inches
23.0 x 19.9 x 23.3
9.1 x 7.8 x 9.2
24.6 x 35.5 x 23.2
9.7 x 14.0 x 9.1
24.6 x 35.5 x 23.2
9.7 x 14.0 x 9.1
39.3 x 38.3 x 23.3
15.5 x 15.1 x 9.2
Bath Work Area
Dimensions
(L x W x H) cm
inches
13.8 x 15.5 x 15.0
5.4 x 6.1 x 5.9
15.3 x 30.0 x 6.5
6.0 x 11.8 x 2.6
15.4 x 30.0 x 15.0
6.1 x 11.8 x 5.9
30.1 x 33.0 x 15.0
11.9 x 13.0 x 5.9
Approximate Weight kg
lb
3.5
7
4
9
4.5
10
7.5
16
Electrical
Requirements (VAC/Hz)
(Voltage ±10%)
100-115/50-60
or
200-230/50-60
Compliance CE RoHS
UL WEEE
Maximum Relative
Humidity
(Non Condensing)
80% (up to 31°C)
80% (up to 88°F)
Operating Altitude meters
feet
Sea Level to 2000
Sea Level to 6560
Overvoltage Category II
Pollution Degree 2
Storage Temperature °C
Range °F
-25 to +60
-13 to +140