Fluke CableIQ CIQ-100 User manual

CableIQTM
Qualification Tester
PN 2113427
January 2005, Rev. 3 9/2018
© 2005, 2007, 2015, 2018 Fluke Corporation
All product names are trademarks of their respective companies.
Getting Started Guide
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

LIMITED WARRANTY
AND LIMITATION OF LIABILITY
Fluke Networks mainframe products will be free
from defects in material and workmanship for one
year from the date of purchase, unless stated
otherwise herein. The CableIQ wiremap adapter
is also warranted for one year. Parts, accessories,
product repairs and services are warranted for 90
days, unless otherwise stated. Ni-Cad, Ni-MH and
Li-Ion batteries, cables or other peripherals are
all considered parts or accessories. This warranty
does not cover damage from accident, neglect,
misuse, alteration, contamination, or abnormal
conditions ofoperation orhandling. Resellers
are not authorized to extend any other warranty
on Fluke Networks’ behalf. To obtain service
during the warranty period, contact your nearest
Fluke Networks authorized service center to
obtain return authorization information, then
send your defective product to that Service
Center with a description of the problem.
For a list of authorized resellers, visit
THIS WARRANTY IS YOUR ONLY REMEDY. NO
OTHER WARRANTIES, SUCH AS FITNESS FOR A
PARTICULAR PURPOSE, ARE EXPRESSED OR
IMPLIED. FLUKE NETWORKS IS NOT LIABLE FOR
ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING
FROM ANY CAUSE OR THEORY. Since some
states or countries do not allow the exclusion or
limitation of an implied warranty or ofincidental
or consequential damages, this limitation of
liability may not apply to you.
4/15-CIQ
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

1
CableIQ™Qualification Tester
Accessing the Users Manual
This guide provides basic information to help you
quickly get started using the tester. The CableIQ
Qualification Tester Users Manual on the Fluke
Networks website provides additional information.
WSafety
WWarningX
To avoid possible fire, electric shock, or personal
injury:
• The tester is not intended to be connected to
active telephone inputs, systems, or equipment,
including ISDN devices. Exposure to the
voltages applied by these interfaces may
damage the tester and create a potential shock
hazard. Disconnect the tester if the voltage alert
symbol () appears.
• Read the safety information given in the Safety
Information booklet before using the tester.
Controls
AXY01
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

CableIQ Getting Started Guide
2
Setting User Preferences
Turn the rotary switch to SETUP; then use  and
to select a setting.
•User Information: Three lines of text are stored
with saved Autotests.
•Language / ftm: Select a language for the
display. Select feet or meters for length
measurements.
•Time / Date: Timestamp saved Autotests.
•Auto Shutoff: The tester stays on indefinitely or
turns off after 15 minutes of inactivity.
Editing Text
Use the keys to edit text on the User Information and
Enter ID screens.
: Selects the highlighted field for editing.
: Moves the cursor. Moving the cursor beyond the
last character inserts the first character from the last
character’s set.
: Changes the highlighted character.
Ins: Inserts the first character from the set that
includes the highlighted character.
Del: Deletes the highlighted character.
SHIFT and or SHIFT and : Changes the
character set.
Character Sets Available
A B C D E F G H I J K L M N O P Q RS T U V W X Y Z
a b c d e f g h i j k l m n o p q r s t u v w x y z
0 1 2 3 4 5 6 7 8 9
#"!$%&'( )*+,-./:;<=>?@[ \ ]^_ `{ | } space
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

Connecting for Cabling Tests
3
Connecting for Cabling Tests
Notes
A wiremap adapter or remote ID locator
must be connected to the end of the cabling
for the wiremap to be completely verified.
If you use patch cords at the near or far end
during an Autotest, Fluke Networks
recommends patch cords at least 2 m long.
Connecting to a Data Link
AXY10
Connecting to a Bus Topology
AXY13
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

CableIQ Getting Started Guide
4
Connecting to a Star Topology
AXY12
Connecting to Coaxial Cabling
AXY34
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

Results Icons
5
Results Icons
The icons below appear on Autotest and Discover
screens.
The cabling qualifies for the application.
The cabling does not qualify for the
application.
Results are for informational purposes
only, not for qualification. The cabling
cannot be completely qualified for the
application because the wiremap results
are incomplete (wiremap adapter not
used).
Pair is open.
Pair is shorted.


Wiremap adapter or remote ID locator at
far end, with its number.
Bridge tap detected.
Hub, switch, or PC NIC card detected. Port
speeds are 10, 100, 1000 Mb/s.
Voltage detected. This may indicate an
active telephone circuit, ISDN line, or
Power over Ethernet (PoE) device.
The tester is connected to an active
telephone circuit.
A signal is present on the pair.
The tester cannot identify the termination.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

CableIQ Getting Started Guide
6
Discovering Cabling Characteristics
Discover mode lets you quickly check wiremaps,
measure length, and determine if cabling is connected
to a network port, video device, or telephone.
Turn the rotary switch to DISCOVER, then connect to
twisted pair or 75 coaxial cabling with or without a
wiremap adapter at the far end. Results from Discover
mode cannot be saved.
Discover Mode on Twisted Pair Cabling
AXY46
Discover Mode on a Bridge Tap
AXY49
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

Discovering Cabling Characteristics
7
Discover Mode on a Port
AXY48
Discover Mode on Coaxial Cabling with Adapter
AXY50
Discover Mode on Coaxial Cabling Connected to a
Device
AXY35
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

CableIQ Getting Started Guide
8
Discover Mode with MultiMap
Verifies wiremaps of multiple telephone outlets
connected in a star or bus topology.
AXY07
Qualifying Cabling with the Autotest
The Autotest tells you if cabling will support a selected
application. You can save Autotest results to
document an installation.
Connect to the cabling as shown on pages 3 and 4.
Turn the rotary switch to AUTOTEST. To select tests
and pairs to test, press Setup. To start the test,
press .
Note
The Autotest does not support use of
multiple remote ID locators (the MultiMap
function).
To save the test, press . You can enter a Site
name, Location, and Outlet to identify the results. The
last character of the Outlet string increments each
time you save an Autotest.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

Using the Toner
9
Autotest Results for Twisted Pair Cabling
AXY14
Using the Toner
Turn the rotary switch to TONE; then select a tone
function. The two IntelliTone™functions work with a
Fluke Networks IntelliTone probe. The other four
analog tones can be detected by most tone probes.
AXY06
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

CableIQ Getting Started Guide
10
Blinking a Port Light
The Blink Port Light function helps you determine
which cable is connected to which port on a network
hub or switch.
The tester’s analog toner is also active when the port
light function is active.
Turn the rotary switch to DIAG; then select Blink Port
Light. Look for the blinking activity LED on the hub or
switch.
AXY05
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

Testing for Continuity
11
Testing for Continuity
The continuity function lets you test for opens and
shorts on the 8-pin modular jack or the coaxial
connector.
Turn the rotary switch to DIAG. Use to highlight
Continuity; then press , , or .
The tester’s beeper is silent for resistances above about
5000 . The beeper’s tone and rhythm increase as
resistance decreases.
AXY37
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

CableIQ Getting Started Guide
12
Using the Continuity Toner
Turn the rotary switch to DIAG; then select Continuity.
The beeper’s tone and rhythm increase as resistance
decrease.
AXY38
Locating Crosstalk and Impedance
Faults
The Find Crosstalk Fault and Find Impedance Fault
functions let you quickly check cable pairs for crosstalk
and impedance faults on twisted pair cabling.
Turn the rotary switch to DIAG, select Find Crosstalk
Fault or Find Impedance Fault; then press or .
Select a transmission standard and pair or pairs to test;
then press . A wiremap adapter or ID locator is not
required.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

Testing Speaker Cabling
13
Testing Speaker Cabling
The Speaker Test generates audible tones for testing
the wiring and phase of installed twisted pair speaker
cabling.
Turn the rotary switch to Diag; then select Speaker
Test.
AXY39
4-clip test lead wiring:
+Pair 12: green +Pair 45: blue
-Pair 36: orange -Pair 78: brown
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

CableIQ Getting Started Guide
14
Replacing the Batteries
Contacting Fluke Networks
Fluke Networks operates in more than 50 countries
worldwide. For more contact information, visit our
website.
AXY53
Remove the yellow
boot to access battery
door.
4 AA batteries
(alkaline
recommended)
20 hours typical
battery life.
w

www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30