FOR-A HVS-3800HS Quick setup guide

HVS-3800HS
HVS-3800S
Digital Video Switcher
(3rd Edition - Rev.2 - 2008/03/06)
CONNECTO
R
INFORMATION

2
 ALARM Connector
Pin Assignment Table (9-pin D-sub female)
Pin No. Signal Name Description
1 FAN ALARM OUT Fan failure alarm. Normally open.
2 POWER ALARM OUT Power supply failure alarm. Normally open.
3 EXTALARM COMMON Not used
4 EXTALARM OUT Not used
5 RESET IN External reset input. Active low initiate.
6 FAN ALARM COMMON Fan alarm common.
7 POWER ALARM
COMMON Power supply alarm common.
8 GND Common ground
9 GND Common ground
*Max. contact load of 0.8A DC.
Cable Connectors
9-pin D-sub connector (male) with inch security lock screws needed for user cable
fabrication.
Fan alarm
Pins 1, 6 remain OPEN during normal operation. If fan failure occurs at HVS-3800HS/S side,
pins 1, 6 will short and fan alarm signal output occurs.
Power supply alarm
Pins 2, 7 remain OPEN during normal operation. If a power supply failure occurs, pins 2, 7
will short and power supply alarm signal output occurs.
External reset
External reset signal input to pin 5, shorts pin 8 to pin 9. MUreset occurs when short initiated.

3
 EDITOR Connector
Pin Assignment Table (9-pin D-sub, female)
Pin No. Signal Name Description
1 FG Frame ground
2 T- Transmit data (-)
3 R+ Receive data (+)
4 SG Signal ground
5 - Not used
6 SG Signal ground
7 T+ Transmit data (+)
8 R- Receive data (-)
9 FG Frame ground
Cable Connectors
9-pin D-sub connector (male) with inch security lock screws needed for user cable
fabrication.
 RS-422 Connector
Pin Assignment Table (9-pin D-sub, female)
Pin No. Signal Name Description
1 FG Frame ground
2 R- Receive data (-)
3 T+ Transmit data (+)
4 SG Signal ground
5 - Not used
6 SG Signal ground
7 R+ Receive data (+)
8 T- Transmit data (-)
9 FG Frame ground
Cable Connectors
9-pin D-sub connector (male) with inch security lock screws needed for user cable
fabrication.

4
 GPI IN Connector
Pin Assignment Table (15-pin D-sub, female)
Pin No. Description
1 TRANS-TYPE M/E1-BKGD-AUTO (default setting)
2 TRANS-TYPE M/E1-KEY1-AUTO (default setting)
3 TRANS-TYPE M/E1-KEY2-AUTO (default setting)
4 TRANS-TYPE M/E1-KEY3-AUTO (default setting)
5 TRANS-TYPE M/E2-BKGD-AUTO (default setting)
6 TRANS-TYPE M/E2-KEY1-AUTO (default setting)
7 TRANS-TYPE M/E2-KEY2-AUTO (default setting)
8 TRANS-TYPE M/E2-KEY3-AUTO (default setting)
9 No assignment (default setting)
10 No assignment (default setting)
11 N/C
12 N/C
13 Signal ground
14 Signal ground
15 Signal ground
*Where “default” in table above denotes factory set default pin assignments.
Cabling
15-pin D-sub connector (male) with inch security lock screws needed for user cable
fabrication.
Pin Free Assign
Pin1 to 10 signal assignments shown above are factory default settings. These can be
changed in operational menus. See section 16-1-1. “GPI IN Free Assignments” for more
details.
Circuit
HVS-3800HS/S
VccVcc
External Device
Open corrector
HVS-3800HS/S
VccVcc
External Device
Switch or Relay

5
 GPI/TALLY OUT Connector
Pin Assignment Table (25-pin D-sub female)
Pin No. Description
1 M/E1-BKGD TRANSITION (default setting)
2 M/E1-KEY1 TRANSITION (default setting)
3 M/E1-KEY2 TRANSITION (default setting)
4 M/E1-KEY3 TRANSITION (default setting)
5 M/E2-BKGD TRANSITION (default setting)
6 M/E2-KEY1 TRANSITION (default setting)
7 M/E2-KEY2 TRANSITION (default setting)
8 M/E2-KEY3 TRANSITION (default setting)
9 Not assigned (default setting)
10 Not assigned (default setting)
11 Not assigned (default setting)
12 Not assigned (default setting)
13 Not assigned (default setting)
14 Not assigned (default setting)
15 Not assigned (default setting)
16 Not assigned (default setting)
17 Not assigned (default setting)
18 Not assigned (default setting)
19 Not assigned (default setting)
20 Not assigned (default setting)
21 Frame ground
22 Frame ground
23 Frame ground
24 Frame ground
25 +5V output (MAX 0.5A) (*1)
*Where “default” in table above denotes factory set default pin assignments.
Cabling
25-pin D-sub connector (male) with inch security lock screws needed for user cable
fabrication.
(*1) Max. contact load of 0.5ADC.
Pin Free Assign
Pin1 to 20 signal assignments shown above are factory default settings. These can be
changed in operational menus. See section 16-1-2. “GPI OUT Free Assignments” for more
details.

6
Circuit
Max voltage: 40V
External DeviceHVS-3800HS/S
Max load current:
100mA