FRAME IT ALL 300001228 User manual

300001228/300001232
300001510/300001511
300001369 (Sandbox Canopy/Cover)
300001370 (Sandbox Canopy/Cover)
SANDBOX
HEXAGON
Customer Service: 1800-914-9835 | [e-mail]
© Frame It All. All Rights Reserved.
ASSEMBLY INSTRUCTIONS
STEP 1:
Assemble the timbers by sliding one end of timber into channel end
of one of the brackets. Use plugs to cover the holes on both sides to
lock the bracket in place.
Repeat this process on the opposite end of the timber flipping the bracket in the opposite
direction (see image below). Repeat for all timbers.
How the Joints Work
Use plugs to
cover the holes
–two plugs are
required per
bracket (1 on
each side)
Use a Capto
complete the
top level.
Use Stacking
stakes for
ground level
framesor
borders.
ONLYuse
Stacking Stakes
when creating
additional levels.
Use stacking
stake when
creating a
multi-level
Stacking stake fit
into the tops of
other Stacking
stakes
STEP 2:
Layout the base level of your raised garden in a hexagon (6-sided) shape, using 6 x 2’
timbers. Insert stake through the hole of the bracket and into each of the corners to lock
all sides in place. Adjust accordingly to your desired shape.
Use plugs (included)
to cover the holes on
both side of timbers
ASSEMBLY INSTRUCTIONS –For Product with Second Levels
STEP 3:
For the second level, use 6 timbers and the stacking stakes. Insert one stake through the
brackets into the hole on top of the stake beneath it to lock the second level in place.
Lastly, add the caps to each of the top corner joints to finish off the raised garden.
STEP 2a: For one level, add caps to each of the top
corner joints to finish off the raised garden.
HAPPY GARDENING!
FOR INDOOR &
HARD SURFACE:
If you plan to assemble sandbox on a hard surface, use
hacksaw to remove the spike of each stake. Use these
cut down stakes for the base level only of your
sandbox.
Trim stake spike
with hacksawfor
use indoor or on
hard surfaces
**NOTE
Stacking stakes can be used on all levels
and when creating additional levels.
ONLY Stacking Stakes can stack!
SKU# 300001369 COMBO KIT CONTAINS:
•Composite timbers 4’ x 6
•Brackets x 12
•**Stakes x 6
•Plugs x 24
•Caps x 6
•Sandbox Canopy/Cover x 1
•Telescoping Poles x 6
SKU# 300001228 | 300001232 KIT CONTAINS:
•Composite timbers 4’ x 12
•Brackets x 24
•**Stakes x 12
•Plugs x 48
•Caps x 6
SKU# 300001370 COMBO KIT CONTAINS:
•Composite timbers 4’ x 12
•Brackets x 24
•**Stakes x 12
•Plugs x 48
•Caps x 6
•Sandbox Canopy/Cover x 1
•Telescoping Poles x 6
SKU# 300001510 | 300001511 KIT CONTAINS:
•Composite timbers 4’ x 12
•Brackets x 24
•**Stakes x 12
•Plugs x 48
•Caps x 6
•Sandbox Canopy/Cover x 1
Layout your timbers along the borderline
and connect each timber together by
inserting the top of the stake through the
bracket loops with the stake pointing to
the sky. This enables you to freely position
your border to get your desired location.

Customer Service: 1800-914-9835 | [e-mail]
© Frame It All. All Rights Reserved.
ASSEMBLY INSTRUCTIONS –Telescoping Canopy/Cover
FORMING THE CANOPY DOME
STEP 1: In an open area, position the canopy so that the inside of the canopy (with canopy
supports showing) is facing up.
STEP 2: Manually expands the canopy spokes evenly in each direction as much as
possible.
STEP 3: Using your foot, step on the center hub of the canopy to invert and lock the
supports in place. The canopy will ‘flip’ into its proper convex shape and become stable –
refer to image below.
ASSEMBLY INSTRUCTIONS –Telescoping Canopy/Cover
ATTACHING THE CANOPY (NOTE: 2-person job to make it much easier)
STEP 1: Position canopy top so that canopy connectors are aligned with support poles.
STEP 2: Insert support pole into canopy connector cap
(refer to image on left).
Repeat with remaining poles.
STEP 3: Extend the top telescoping to its full length.
STEP 4: Pull canopy flaps together at each corner and
affix with Velcro straps.
TO CONVERT TO SANDBOX COVER
Release the highest clamp on each pole.
Canopy will now slide down to the next
set of levels. Lock 1st lever, then repeat
with each additional level of clamps until
the poles have fully telescoped into each
other.
STORING THE CANOPY
STEP 1: Remove canopy from telescoping poles. Place on ground right side up (as it came
off the support poles.
STEP 2: Using your foot, step on the central
hub to invert and unlock the canopy supports.
TO CONVERT BACK TO CANOPY
Release each bottom set of levers, then
extend and lock 1st level of telescoping
poles.
Repeat with each additional level.
STEP 3: Compress
canopy sides
together to close.
INSTALLING THE TELESCOPING SUPPORT POLES
STEP 1: Unlock the clamps on the bottom two of the telescoping pole and extend it to its
full length. Lock the clamps to hold it in place.
STEP 2: Remove existing caps from stakes and replace it with caps
that have holes to receive the poles.
STEP 3: Insert widest end of the pole into recess of staking joint stakes
–repeat with remaining poles.
extend