Galvin Engineering Ezy-Drink Lead Safe SS316 Instruction sheet

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 4, 25th October 2022, Page 1of 5
Ezy-Drink®Lead Safe™SS316 Remote
Push Button Drinking Bubbler
PRODUCT CODE:
- TD15XP
SPECIFICATIONS
−The innovative design and 316 Stainless Steel construction ensures there is no risk of lead leaching
into the water from the tapware.
−Drinking taps are designed to operate at full mains pressure.
−The rubber mouthguard is resistant to fungal and bacterial attack and has a high resistance to sunlight.
−Vandal resistant handle.
−Adjustable built-in flow restrictor.
IMPORTANT: All Ezy-Drink®remote bubbler taps are tested in accordance with AS/NZS 3718 and leave
our premises in good working order.
TECHNICAL DATA
Inlet
½”BSP - Female
Outlet
Rubber mouthguard
Headwork
Push button
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
60
Nominal Flow Rate (LPM)
2
Construction
316 Stainless Steel
Finish
Satin
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without
notice.
TOOLS REQUIRED
−Power drill
−Wrench
−2mm Hex Key (provided)
−Screwdriver

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 4, 25th October 2022, Page 2of 5
PRE-INSTALLATION - MOUNTING DETAILS
−If the mounting holes do not already exist, mark out and drill the holes in the bench/trough, as shown in
rough-in dimensions.
Note: Supplied flexi hose length is 225mm long. Maximum distance between outlet and handle is 180mm.
Note: Before installation, all lines must be flushed.
We recommend that a line strainer be installed prior to drinking taps to eliminate any foreign material
INSTALLATION
IMPORTANT: Galvin Engineering products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with
these provisions shall void the product warranty and may affect the performance of the product.
1. Disassembly
−Remove the push button handle using the
provided 2mm hex key to loosen the grub
screw.
−Remove the stainless steel lock nut using
an appropriate sized wrench. Do not
remove the top assembly.
−Remove back nut and cup washer from the
outlet assembly.
2. Fit body & mouthguard outlet
−Fit the valve body and mouthguard outlet into the
trough ensuring the rubber washers are placed
between.
−Secure outlet underneath with the supplied cup
washer and back nut.
−Secure valve body using the stainless steel locknut.
−Take care not to over-tighten.
Rough-In Dimensions
*Only drill Ø2.5mm hole if anti-
rotation pin (not supplied) is
required.

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 4, 25th October 2022, Page 3of 5
3. Tighten locknut and fit handle
−To resist theft/vandalism, ensure the
stainless steel locknut is tightened firmly
using an appropriate wrench.
4. Secure push button handle
−Lock push button handle in place by fitting grub
screw and tightening using 2mm hex key. Take
care not to overtighten.
5. Fit flexi-hose
−Fit flexi hose to outlet and body as shown.
6. Testing
−Once the drinking tap has been installed and tested
for leaks, the water height must be adjusted to suit
the available pressure.
−To adjust water flow
1. Remove the blanking screw .
2. Adjust the water height by turning the regulator
screw .
3. Replace blanking screw.
Note: The full range from minimum flow to maximum
flow is only ¼ turn.

Version 217 November 2022, Page 4
of 4
Product Installation Guidelines
Version 4,11th October 2022, Page 5 of 5
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Inconsistent flow
Blocked top assembly
Remove top assembly and clean
Water is not flowing from
tap
Water is turned off
Turn on water
Blocked flow restrictor
Remove restrictor and clean
Continuous flow
Top assembly loose or
internally obstructed or
damaged
Remove top assembly, clean with water
and re-grease spindle if required
Rate of flow inadequate
The flow regulator screw may
not be adjusted correctly
Remove blanking screw and adjust flow
regulating screw as described above
Button hard to press
The mains pressure may be
too great
Reduce to below 500kPa (70PSI).
Regrease spindle if required
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering
Pty Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or
implied. Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied,
including but not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy
for breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.