Galvin Engineering CliniLever TM-SNKGX Instruction sheet

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 2.1, 2 December 2021, Page 1of 6
CliniLever®Stainless Steel Lead Safe™
Gooseneck Sink Mixer
PRODUCT CODES:
−TM-SNKGX
SPECIFICATIONS
−Lead Safe™stainless steel construction
−Clean hygienic design
−Low maintenance and easy to operate
−Smooth round designs to facilitate easy cleaning and help reduce dirt and bacteria growth.
IMPORTANT: All CliniLever®Taps are tested in accordance with AS/NZS 3718 and leave our premises in
good working order.
TECHNICAL DATA
Inlet
½” BSP – Female (Flexi-hoses)
Outlet
Aerator
Headwork
Ceramic Cartridge
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature Range (°C)
Min
5
Max
80
Nominal Flow Rate (LPM)
5.92
Construction
Stainless Steel
Finish
Stainless Steel
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without
notice.

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 2.1, 2 December 2021, Page 2of 6
DIMENSIONS
- If the mounting hole does not already exist,
mark out and drill the hole in the sink, as
shown in the rough-in dimensions.
Note: Before installation, all lines must be flushed. We
recommend that a line strainer be installed prior to the
CliniLever® Sink Mixer to eliminate any foreign
material.
INSTALLATION
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product.
1. Fit Mounting Hardware and Hoses
−Screw in and tighten flexi-hoses. Insert the
flexi-hoses as how the indications on the
handle are shown. (Left hole for Hot and
Right hole for Cold)
−Fully screw threaded rod as shown.
2. Fit Tap
−Ensure the sink mounting hole for the tap is as
per the rough-in dimensions.
−Ensure the Bottom ring is present underneath
the tap.
−Carefully fit the flexible hoses and threaded rod
through the sink hole as shown.
Version 1, 2 December 2021, Page 2 of 9
Ø30 MIN
Ø38 MAX
Rough-In Dimensions
Bottom Ring
Hot Inlet
Cold Inlet
Threaded rod

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 2.1, 2 December 2021, Page 3of 6
3. Secure Tap
−Fit the mounting gasket and bracket as
shown.
−Screw hex nut on threaded rod finger tight.
4. Tighten Installation
−Tighten the hex nut using the provided tool as
shown.
−Ensure the tap body doesn’t move on the sink
once tightened.
5. Connect Water and Test
−We recommend the use of wall mounted isolating valves (not included).
−Ensure water supply lines are flushed before connecting.
−Connect the flexible hoses to the mains water as shown ensuring the hot and cold hoses are correct.
−Test the tap for leaks and correct operation.
Red-labelled hose
Wall Valves
(Not Included)
Blue-labelled hose
Mounting
gasket
Bracket
Hex nut
Hex nut
Spanner

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 2.1, 2 December 2021, Page 4of 6
REMOVE & INSPECT FLOW REGULATING AERATOR
1. Remove Flow Regulating Aerator Housing
-Remove the flow regulating aerator housing as
shown.
2. Remove & Inspect
−Remove the flow regulating aerator.
−Inspect for debris and clean. Replace if
necessary.
3. Reassemble
−Reverse steps 2 & 1 to reassemble ensuring the orientation is correct.
−Test for leaks and correct operation.
Flow
Regulating
Aerator

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 2.1, 2 December 2021, Page 5of 6
REMOVE & INSPECT CARTRIDGE
1. Remove Handle
−Ensure the water supply is closed.
−Unscrew the handle and remove the grub
screw.
−Remove the handle body
2. Remove Cap and Retaining Nut
−Unscrew the cap and retaining nut from
the body
3. Remove and Inspect Cartridge
−Remove Cartridge
−Inspect for debris and clean. Replace if
necessary.
Note: For cartridge replacement, use WaterMarked
Standard/Universal 35mm Flat Cartridge. For more
information, please contact Galvin Engineering
4. Reassemble
−Reverse steps 1 to 3 to reassemble
ensuring the orientation is correct.
−Test for leaks and correct operation.
Handle
Grub screw
Handle body
Retaining nut
Cap
Cartridge

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 2.1, 2 December 2021, Page 6of 6
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty
Ltd. With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied.
Galvin Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but
not limited to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download
from www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free
from operational defects in workmanship and materials for the warranty period as shown on the schedule in
the manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any
defective products manufactured by Galvin Engineering without charge, so long as the terms of the
Manufacturer’s warranty are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other
property which is damaged if this product does not work properly, other costs resulting from labour charges,
delays, vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions,
chemical, electrical or any other circumstances over which Galvin Engineering has no control. This warranty
shall be invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or
alteration of the product.
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Tap is leaking
Cartridge damaged
Remove and inspect the cartridge,
remove debris and/or replace if
damaged
Tap incorrectly installed
Follow the installation steps above
when fitting the tap.
Tap has inconsistent flow
Blocked flow regulator
Follow the instructions above to
remove flow regulator from the body
and check for debris. Install an inline
strainer to stop further blockages.
Tap moves on basin
Insufficiently tightened
Follow the steps above in relation to
tightening the installation.
Water temperature is opposite to the
handle markings
Inlet hoses connected
incorrectly
Switch the hoses connection on the
inlets
Inlet hoses connected to wrong
isolating valves
Switch the hoses connection on the
isolating valves