Galvin Engineering BS Capstan SBA Instruction sheet

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Document No.: 001.00.30.14
Version 1, 4 October 2022, Page 1of 4
CP-BS Wall/Pillar/Bib/Basin SBA
PRODUCT CODES:
- 32728 (BS Capstan SBA)
- 48751 (BS Stirling SBA)
- 50015 (Vandal Resistant CP-BS SBA)
- 35793 (Ezy-Twist CP-BS SBA)
SPECIFICATIONS
−The main body is made of solid dezincification resistant (DR) brass rod, with a DR brass fixed outlet.
IMPORTANT: All taps are tested in accordance with AS/NZS 3718 and leave our premises in good working
order.
TECHNICAL DATA
Inlet
G 5/8”BSP
Outlet
N/A
Headwork
32728
Ceramic Disc
48751, 50015
Jumper Valve
35793
Cam Action
Working Pressure Range (kPa)
Min
50
Max
500
Working Temperature (°C)
Min
5
Max
80
Nominal Flow Rate (LPM)
N/A
Finish
Brass
NOTE: Galvin Engineering continually strive to improve their products. Specifications may change without notice.
TOOLS REQUIRED
−Spanner and hex key
−Thread tape

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 4 October 2022, Page 2of 4
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions and in
accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical supply
conditions must also comply to the applicable national and/or state standards. Failing to comply with these provisions
shall void the product warranty and may affect the performance of the product.
Note: (Illustrations are for representation of installation only and is not limited for use to these components)
1. Remove Handle
−Prior to installation turn off the water supply.
−Remove the handle assembly. To prevent
damage, carefully pry off plastic indicator from
the handle. (Use a small flat bladed screwdriver
if necessary).
2. Replace spindle assembly
−Unscrew the head part from the threaded sleeve
using a 17mm spanner.
−Check seat inside tap body for pitting or damage.
Re-seat if necessary
3. Refit new head part
-Refit new head part into tap body.
Note: do not tighten cartridge using the handle
as this will result in damage to the cartridge
4. Reassemble Handle
-Refit adaptor and reassemble handle by reversing
step 1.
-When installation is complete, slowly open water
supply and inspect for leaks.
New ceramic head
New head part

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 4 October 2022, Page 3of 4
TROUBLESHOOTING
PROBLEM
CAUSE
RECTIFICATION
Taps are dripping water
Ceramic discs are worn or damaged
Remove and inspect SBA. Remove
debris and/or replace SBA if
damaged.
Tap seat is damaged
Refurbish tap seat using a reseating
tool.
Water is not flowing from tap
Water is turned off
Turn on water
Ceramic discs are worn or damaged
Remove and inspect SBA. Remove
debris and/or replace SBA if
damaged.
Spindle is difficult to turn
Ceramic discs are worn or damaged
Remove and inspect SBA. Remove
debris and/or replace SBA if
damaged.
Handle is loose
Screw has come loose
Tighten handle screw

© Galvin Engineering Pty Ltd
Product Installation Guidelines
Version 1, 29 August 2022, Page 4of 4
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd.
With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin
Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but not limited
to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective products
manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s warranty are
complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property
which is damaged if this product does not work properly, other costs resulting from labour charges, delays,
vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical,
electrical or any other circumstances over which Galvin Engineering has no control. This warranty shall be
invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the
product.