Galvin Engineering CliniMix WM-PMSKIT Instruction sheet

Version 1, 22 October 2019, Page 1of 6
CliniMix®Inwall Shower Disinfection kit
PRODUCT CODE:
- WM-PMSKIT
SPECIFICATIONS
The Inwall Shower Disinfection Plug Kit allows a technician to safely perform the disinfection procedure on
Galvin Engineering in-wall thermostatic mixers.
This kit is effective in killing bacteria formed by stagnant water.
Includes a shower head adaptor and hose to safely pass the hot water from the shower to the floor drain.
IMPORTANT SAFTEY NOTE: Care should be taken when carrying out the disinfection procedure to avoid contact
with hot water and hot surfaces. We recommend the use of protective hand wear.
TECHNICAL DATA
To Suit Shower Body’s
WM-TMVPMS, WM-
TMVPMSCS, WM-
TMVPMSCSUS, WM-
TMVPMSCS1
To Suit Shower Outlet
Vandal Resistant Shower
Rose (40691)
Working Pressure Range (kPa)
Min
20
Max
500
Working Temperature Range (°C)
Min
60
Max
90
NOTE: Galvin Specialised continually strive to improve their products. Specifications may change without notice.
COMPONENT DIMENSIONS

Version 1, 22 October 2019, Page 2of 6
PRE-INSTALLATION
IMPORTANT:
INSTALLATION COMPLIANCE: Galvin Engineering products must be installed in accordance with these
installation instructions and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements.
Water and/or electrical supply conditions must also comply to the applicable national and/or state standards.
Failing to comply with these provisions shall void the product warranty and may affect the performance of the
product (Refer to supplied installation compliance sheet with the product).
SAFETY NOTE: Care should be taken when carrying out the disinfection procedure to avoid contact with hot water
and hot surfaces. We recommend the use of protective hand wear.
INSTALLATION
IMPORTANT: Galvin Specialised products must be installed in accordance with these installation instructions
and in accordance with AS/NZS 3500, the PCA and your local regulatory requirements. Water and/or electrical
supply conditions must also comply to the applicable national and/or state standards. Failing to comply with these
provisions shall void the product warranty and may affect the performance of the product.
1. Fit Flange/Outlet End
Remove the M4 screws from shower rose.
Place the shower rose in the flange locating over
the thumb screws (supplied).
Ensure o-ring on flange is fitted.
Secure flange to shower body using thumb
screws ensuring they are hand tight to form an
adequate seal.
The supplied drainage hose is to suit Galvin
Engineering Vandal Resistant Shower (40691).
The use of a drainage hose is important to
minimise the risk of scalding during the
disinfection process. Please contact Galvin
Engineering for more information.
2. Direct Outlet to Drain
Place hose end on the floor in the direction of the drain
to ensure hot water exits in a controlled manner.
Failure to do so may result in the user being
scalded by hot water.

Version 1, 22 October 2019, Page 3of 6
3. Remove handle assembly
Unscrew the tamper proof screw from the handle.
Pull out handle assembly from the body.
4. Remove faceplate and flange
Unscrew the three screws and pull out the flange and
faceplate from the unit.
5. Isolate shower
To isolate the shower:
Remove wire clips.
Using a hex key, turn the isolators in an anti-
clockwise direction until fully removed.
6. Turn on Cold water
Temporarily fit the handle to the cartridge.
Turn handle clockwise until it stops.
Turn handle anti-clockwise 45⁰ (1/8th turn) to open
the cold side of the mixing valve allowing hot water to
flow through it.
Remove the handle without rotating.

Version 1, 22 October 2019, Page 4of 6
7. Fit disinfection unit
Ensure both handles on the disinfection unit are
fully turned anti-clockwise and the centre nut is
tight.
Fit the disinfection unit by screwing the hot and
cold extensions in even increments into the
shower body as shown.
Do not screw in one side fully at a time as this
will damage the disinfection unit.
Evenly tighten the knurled pieces until the
extensions are fully locked in place.
The unit will not seal if not fully tightened.
This will put the user at risk of exposure to
scalding water.
8. Activate hot handle
Turn hot handle clockwise (until handle stops) to allow
water to flow from the hot side of the shower through
the cold side.
Do not over tighten as this will damage the
disinfection unit.
9. Disinfection
Although the drainage hose will facilitate the safe drainage of the hot water, it is recommended that you
do not stand under the shower during the disinfection process.
Upon activating the hot handle, hot water will pass from the hot inlet to the cold inlet and into the thermostatic
mixing chamber then out the shower outlet (exiting through the drainage hose).
Run water for the correct disinfection time as shown in table.
Disinfection Temperature vs. Time:
Temperature
Disinfection Time
60°C
30 Minutes
65°C
15 Minutes
70°C
10 Minutes
Note: The temperature of the exiting water should be checked regulary to ensure the correct timing
and the desired level of disinfection takes place.

Version 1, 22 October 2019, Page 5of 6
10. Cool down unit
1. Turn off hot water by rotating hot handle anti-
clockwise.
2. Turn cold handle clockwise (until handle stops) to
introduce cold water to the system. The cold water
will flush out the hot water, hence cooling the unit.
The handles may heat up during the disinfection
process. The use of protective hand wear is
recommended.
This unit becomes very hot during operation.
Cooling the unit is essential before removing
11. Re-assemble
Ensure enough time is given for the cold water
cooling process of the disinfection unit. Once cool
to the touch the unit can be removed.
First, turn off cold water by rotating disinfection unit
cold handle anti-clockwise.
Remove disinfection unit, by reversing step 7.
Re-assemble shower unit, by reversing steps 5 to 3.
Re-assemble shower outlet by reversing steps 2 & 1.
Turn on the water and check for correct operation.
2
1

Version 1, 22 October 2019, Page 6of 6
TROUBLE SHOOTING
PROBLEM
CAUSE
RECTIFICATION
Cold instead of hot
water flowing
Cold water handle is turned on
instead of hot.
The disinfection unit has been
installed incorrectly.
Ensure the hot handle has been fully turned
clockwise and the cold is fully turned off.
Follow installation steps 3 –9 and ensure the
unit has been installed correctly.
Water not flowing
The disinfection unit has been
installed incorrectly.
Follow installation steps 3 –9 and ensure the unit
has been installed correctly.
Cold or hot handle not turned on
fully.
Ensure the relevant handle is turned fully
clockwise.
No mains water.
Contact your maintenance manager.
WARRANTY
The warranty set forth herein is given expressly and is the only warranty given by the Galvin Engineering Pty Ltd.
With respect to the product, Galvin Engineering Pty Ltd makes no other warranties, express or implied. Galvin
Engineering Pty. Ltd. hereby specifically disclaims all other warranties, express or implied, including but not limited
to the implied warranties of merchantability and fitness for a particular purpose.
Galvin Engineering Pty Ltd products are covered under our manufacturer’s warranty available for download from
www.galvinengineering.com.au Galvin Engineering Pty Ltd expressly warrants that the product is free from
operational defects in workmanship and materials for the warranty period as shown on the schedule in the
manufacturer’s warranty. During the warranty period, Galvin Engineering will replace or repair any defective
products manufactured by Galvin Engineering without charge, so long as the terms of the Manufacturer’s warranty
are complied with.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for
breach of warranty, and Galvin Engineering Pty Ltd shall not be responsible for any incidental, special or
consequential damages, including without limitation, lost profits or the cost of repairing or replacing other property
which is damaged if this product does not work properly, other costs resulting from labour charges, delays,
vandalism, negligence, fouling caused by foreign material, damage from adverse water conditions, chemical,
electrical or any other circumstances over which Galvin Engineering has no control. This warranty shall be
invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of
the product.